EN ISO 8503-4:1995
(Main)Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile - Stylus instrument procedure (ISO 8503-4:1988)
Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile - Stylus instrument procedure (ISO 8503-4:1988)
Based on the measurement of the peaks and valleys by vertical displacement of a stylus traversing the test surface in the direction of travel over the specified traversing length. Determination of the mean maximum peak-to-valley height. Repetition of the procedure to obtain values on not less than ten different locations, followed by the calculation of the grand mean value. The procedure is also applicable to the determination of the surface profile of essentially planar blast-cleaned steel.
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen - Rauheitskenngrößen von gestrahlten Stahloberflächen - Teil 4: Verfahren zur Kalibrierung von ISO-Rauheitsvergleichsmustern und zur Bestimmung der Rauheit - Tastschnittverfahren (ISO 8503-4:1988)
Dieser Teil von ISO 8503 beschreibt das Tastschnittgerät und das Verfahren zur Kalibrierung von ISO-Rauheitsvergleichsmustern, welche den Anforderungen nach ISO 8503-1 entsprechen.
Préparation des subjectiles d'acier avant application de peintures et de produits assimilés - Caractéristiques de rugosité des subjectiles d'acier décapés - Partie 4: Méthode pour étalonner les échantillons de comparaison viso-tactile ISO et pour caractériser un profil de surface - Utilisation d'un appareil à palpeur (ISO 8503-4:1988)
1.1 La présente partie de l'ISO 8503 décrit l'appareil à palpeur et la méthode pour étalonner les échantillons de comparaison viso-tactile ISO répondant aux exigences de l'ISO 8503-1. 1.2 La présente partie de l'ISO 8503 est également applicable à la détermination d'un profil de surface Ry5, dans la gamme de 20 à 200 µm, d'une surface essentiellement plane décapée par projection d'abrasif. La détermination peut être effectuée sur une partie représentative de la surface préparée ou, si l'observation directe n'est pas possible, sur une réplique (voir annexe C).
NOTE -- Dans certains cas, ce mode opératoire peut convenir pour évaluer le profil de rugosité d'autres subjectiles décapés par projection d'abrasif. Une autre méthode est décrite dans l'ISO 8503-3.
Priprava jeklenih podlag pred nanašanjem barvnih in sorodnih premazov - Površinske hrapave karakteristike peskanih jeklenih podlag - 4. del: Metoda za kalibracijo lestvice standardov površinske hrapavosti ISO in za določanje hrapavosti površine - Postopek z instrumentom Stylus (ISO 8503-4:1988)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8503-4:1997
01-december-1997
3ULSUDYDMHNOHQLKSRGODJSUHGQDQDãDQMHPEDUYQLKLQVRURGQLKSUHPD]RY
3RYUãLQVNHKUDSDYHNDUDNWHULVWLNHSHVNDQLKMHNOHQLKSRGODJGHO 0HWRGD]D
NDOLEUDFLMROHVWYLFHVWDQGDUGRYSRYUãLQVNHKUDSDYRVWL,62LQ]DGRORþDQMH
KUDSDYRVWLSRYUãLQH3RVWRSHN]LQVWUXPHQWRP6W\OXV ,62
Preparation of steel substrates before application of paints and related products -
Surface roughness characteristics of blast-cleaned steel substrates - Part 4: Method for
the calibration of ISO surface profile comparators and for the determination of surface
profile - Stylus instrument procedure (ISO 8503-4:1988)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Rauheitskenngrößen von gestrahlten Stahloberflächen - Teil 4: Verfahren zur
Kalibrierung von ISO-Rauheitsvergleichsmustern und zur Bestimmung der Rauheit -
Tastschnittverfahren (ISO 8503-4:1988)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Caractéristiques de rugosité des subjectiles d'acier décapés - Partie 4:
Méthode pour étalonner les échantillons de comparaison viso-tactile ISO et pour
caractériser un profil de surface - Utilisation d'un appareil a palpeur (ISO 8503-4:1988)
Ta slovenski standard je istoveten z: EN ISO 8503-4:1995
ICS:
25.220.10 Priprava površine Surface preparation
87.020 Postopki za nanašanje Paint coating processes
barvnih premazov
SIST EN ISO 8503-4:1997 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8503-4:1997
---------------------- Page: 2 ----------------------
SIST EN ISO 8503-4:1997
---------------------- Page: 3 ----------------------
SIST EN ISO 8503-4:1997
---------------------- Page: 4 ----------------------
SIST EN ISO 8503-4:1997
---------------------- Page: 5 ----------------------
SIST EN ISO 8503-4:1997
---------------------- Page: 6 ----------------------
SIST EN ISO 8503-4:1997
IS0
INTERNATIONAL STANDARD
8503-4
First edition
1988-02-01
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION
ORGANISATION INTERNATIONALE DE NORMALISATION
MEXP,YHAPOAHAfl OPTAHM3A~MR IlO CTAHflAPTM3A~MM
Preparation of steel substrates before application of
paints and related products - Surface roughness
characteristics of blast-cleaned steel substrates -
Part 4 :
Method for the calibration of IS0 surface profile
comparators and for the determination of surface profile -
Stylus instrument procedure
Preparation des subjectiles d’acier avant application de peintures et de produits assimif& -
Caractkistiques de rugosit6 des subjectiles d’acier d&cap& -
Partie 4 : M&hode pour &alonner les e’chantillons de comparaison viso-tactile /SO et pour
caractkriser un profil de surface - Utilisation d’un appareil ;i palpeur
Reference number
IS0 8503-4: 1988 (E)
---------------------- Page: 7 ----------------------
SIST EN ISO 8503-4:1997
Foreword
IS0 (the International Organization for Standardization) is a worldwide federation of
national standards bodies (IS0 member bodies). The work of preparing International
Standards is normally carried out through IS0 technical committees. Each member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the IS0 Council. They are approved in accordance with IS0 procedures requiring at
least 75 % approval by the member bodies voting.
International Standard IS0 8503-4 was prepared by Technical Committee ISO/TC 35,
Paints and varnishes.
Users should note that all International Standards undergo revision from time to time
and that any reference made herein to any other International Standard implies its
latest edition, unless otherwise stated.
0 International Organization for Standardization, 1988
Printed in Switzerland
---------------------- Page: 8 ----------------------
SIST EN ISO 8503-4:1997
IS0 8503-4 : 1988 (E)
INTERNATIONAL STANDARD
Preparation of steel substrates before application of
paints and related products - Surface roughness
characteristics of blast-cleaned steel substrates -
Part 4 I
Method for the calibration of IS0 surface profile
comparators and for the determination of surface profile -
Stylus instrument procedure
IS0 8502 - Tests for the assessment of surface clean-
0 Introduction
liness;
The performance of protective coatings of paint and related
- Surface roughness characteristics of blast-
IS0 8503
products applied to steel is significantly affected by the state of
cleaned st
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.