EN ISO 22557:2020
(Main)Paints and varnishes - Scratch test using a spring-loaded pen (ISO 22557:2019)
Paints and varnishes - Scratch test using a spring-loaded pen (ISO 22557:2019)
This document specifies a method for determining the resistance of a coating to scratches introduced by a usually hand-held loaded stylus.
The test can be carried out using a point stylus (method A) or using a disc stylus (method B).
Both methods are generally applicable and can be used in the field as well as on curved surfaces. Method A can also be applied on small test specimens (minimum dimensions 30 mm × 50 mm).
The test can be carried out as a "pass/fail" test (test requirement I) or as a classification test (test requirement II).
Beschichtungsstoffe - Kratzprüfung mit einem Härteprüfstab (ISO 22557:2019)
Peintures et vernis - Essai de rayage manuel avec un stylo d’essai de dureté (ISO 22557:2019)
Le présent document spécifie une méthode pour déterminer la résistance d'un revêtement aux rayures provoquées par un stylet, généralement portatif, sur lequel une charge est appliquée.
L'essai peut être réalisé avec un stylet à pointe (méthode A) ou un stylet à disque (méthode B).
Les deux méthodes sont généralement applicables, et il est possible de les utiliser sur le terrain ainsi que sur des surfaces courbes. La méthode A peut également être utilisée sur de petites éprouvettes (dimensions minimales: 30 mm × 50 mm).
L'essai peut être mis en œuvre sous la forme d'un essai de conformité/non-conformité (exigence d'essai I) ou d'un essai de classification (exigence d'essai II).
Barve in laki - Preskus razenja z uporabo vzmetnega svinčnika (ISO 22557:2019)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2021
Barve in laki - Preskus razenja z uporabo vzmetnega svinčnika (ISO 22557:2019)
Paints and varnishes - Scratch test using a spring-loaded pen (ISO 22557:2019)
Beschichtungsstoffe - Kratzprüfung mit einem Härteprüfstab (ISO 22557:2019)
Peintures et vernis - Essai de rayage manuel utilisant un barreau d'essai de dureté (ISO
22557:2019)
Ta slovenski standard je istoveten z: EN ISO 22557:2020
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 22557
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2020
EUROPÄISCHE NORM
ICS 87.040
English Version
Paints and varnishes - Scratch test using a spring-loaded
pen (ISO 22557:2019)
Peintures et vernis - Essai de rayage manuel utilisant Beschichtungsstoffe - Kratzprüfung mit einem
un barreau d'essai de dureté (ISO 22557:2019) Härteprüfstab (ISO 22557:2019)
This European Standard was approved by CEN on 30 November 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22557:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 22557:2019 has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes” of the International Organization for Standardization (ISO) and has been taken over as
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2021, and conflicting national standards shall be
withdrawn at the latest by June 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 22557:2019 has been approved by CEN as EN ISO 22557:2020 without any modification.
INTERNATIONAL ISO
STANDARD 22557
First edition
2019-07
Paints and varnishes — Scratch test
using a spring-loaded pen
Peintures et vernis — Essai de rayage manuel utilisant un barreau
d'essai de dureté
Reference number
ISO 22557:2019(E)
©
ISO 2019
ISO 22557:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
ISO 22557:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Test specimens. 6
6.1 General requirements . 6
6.2 Film thickness . 6
6.3 Conditioning . 6
7 Procedure. 7
7.1 Agreements . 7
7.2 Test conditions . 7
7.3 General test procedure . 7
7.4 Constant test load method (test requirement I – “pass/fail” test) . 7
7.5 Varied test load method (test requirement II – classification test) . 7
7.6 Assessment of the damage . 8
8 Precision . 9
8.1 General . 9
8.2 Repeatability limit, r . 9
8.3 Reproducibility limit, R . 9
9 Test report . 9
9.1 Detailed form . 9
9.2 Short form .10
Annex A (informative) Details on the interlaboratory comparison for the estimation precision.11
Bibliography .15
ISO 22557:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
INTERNATIONAL STANDARD ISO 22557:2019(E)
Paints and varnishes — Scratch test using a spring-
loaded pen
1 Scope
This document specifies a method for determining the resistance of a coating to scratches introduced
by a usually hand-held loaded stylus.
The test can be carried out using a point stylus (method A) or using a disc stylus (method B).
Both methods are generally applicable and can be used in the field as well as on curved surfaces. Method
A can also be applied on small test specimens (minimum dimensions 30 mm × 50 mm).
The test can be carried out as a “pass/fail” test (test requirement I) or as a classification test (test
requirement II).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 868, Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore
hardness)
ISO 2808, Paints and varnishes — Determination of film thickness
ISO 4618, Paints and varnishes — Terms and definitions
ISO 13076, Paints and varnishes — Lighting and procedure for visual assessments of coatings
ISO 14526-1, Plastics — Phenolic powder moulding compounds (PF-PMCs) — Part 1: Designation sys
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.