EN 4373:2007

Aerospace series - Heat resisting alloy NI-PD9001 (NiCu31) - Annealed, seamless tube D ≤ 75 mm, a ≤ 3 mm

This standard specifies the requirements relating to:
Heat resisting alloy NI-PD9001 (NiCu31) — Annealed, seamless tube D ≤ 75 mm, a ≤ 3 mm
for aerospace applications.

Luft- und Raumfahrt - Hochwarmfeste Legierung NI-PD9001 (NiCu31) - Geglüht, nahtlose Rohre D ≤ 75 mm, a ≤ 3 mm

Diese Norm legt die Anforderungen an
Hochwarmfeste Legierung NI-PD9001 (NiCu31)
geglüht
nahtlose Rohre
D ≤ 75 mm, a ≤ 3 mm
für die Anwendung in der Luft- und Raumfahrt fest.

Série aérospatiale - Alliage résistant à chaud NI-PD9001 (NiCu31) - Recuit, tubes sans soudure D ≤ 75 mm, a ≤ 3 mm

Aeronavtika - Zlitina NI-PD9001 (NiCu31), odporna proti vročini - Žarjena, nevarjena cev D <= 75 mm, a <= 3 mm

General Information

• Status: Published
• Publication Date: 28-Aug-2007
• Withdrawal Date: 28-Feb-2008
• ICS: 49.025.15 - Non-ferrous alloys in general
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 4 - Metallic
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 30-Jun-2017
• Ref Project: SIST EN 4373:2007 - Aerospace series - Heat resisting alloy NI-PD9001 (NiCu31) - Annealed, seamless tube D <= 75 mm, a <= 3 mm

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Heat resisting alloy NI-PD9001 (NiCu31) - Annealed, seamless tube D <= 75 mm, a <= 3 mmSérie aérospatiale - Alliage résistant a chaud
NI-PD9001 (NiCu31) - Recuit, tubes sans soudure D <= 75 mm, a <= 3 mmLuft- und Raumfahrt - Hochwarmfeste Legierung NI-PD9001 (NiCu31) - Geglüht, nahtlose Rohre D <= 75 mm, a <= 3 mmTa slovenski standard je istoveten z:EN 4373:2007SIST EN 4373:2007en49.025.15Neželezove zlitine na splošnoNon-ferrous alloys in generalICS:SLOVENSKI
STANDARDSIST EN 4373:200701-november-2007







EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4373
August 2007 ICS 49.025.15 English Version
Aerospace series - Heat resisting alloy NI-PD9001 (NiCu31) - Annealed, seamless tube D ≤ 75 mm, a ≤ 3 mm
Série aérospatiale - Alliage résistant à chaud
NI-PD9001 (NiCu31) - Recuit, tubes sans soudure D ≤ 75 mm, a ≤ 3 mm
Luft- und Raumfahrt - Hochwarmfeste Legierung NI-PD9001 (NiCu31) - Geglüht, nahtlose Rohre D ≤ 75 mm, a ≤ 3 mm This European Standard was approved by CEN on 15 March 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4373:2007: E



EN 4373:2007 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.4 2 Normative references.4



EN 4373:2007 (E) 3 Foreword This document (EN 4373:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2008, and conflicting national sta
...