Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections

This Part 3 in addition to Part 1 of this European Standard specifies the delivery requirements for surface condition of sections to which the European Standards mentioned in clause 2 apply and applies to all surfaces excluding edges.
NOTE   In this European Standard section toes (see EN 10055) are considered as part of the surfaces of a section.

Lieferbedingungen für die Oberflächenbeschaffenheit von warmgewalzten Stahlerzeugnissen (Blech, Breitflachstahl und Profile) - Teil 3: Profile

Zusätzlich zu EN 10163-1 enthält dieses Dokument die Lieferbedingungen für die Oberflächenbeschaffenheit
von Profilen nach den in den Literaturhinweisen genannten Europäischen Normen und gilt für alle
Oberflächen mit Ausnahme der Profilkanten.
ANMERKUNG In diesem Dokument werden Profilübergänge (siehe EN 10055) als Teil der Oberfläche eines Profiles
betrachtet.

Conditions de livraison relatives à l'état de surface des tôles, larges plats et profilés en acier laminés à chaud - Partie 3: Profilés

En complément de l'EN 10163-1, le présent document fixe les prescriptions de qualité de surface des profilés
auxquels s'appliquent les Normes européennes mentionnées à l'Article 2. Il est applicable à toutes les surfaces, à
l'exclusion des rives.
NOTE Dans cette Norme européenne, les coins des profilés (voir EN 10055) sont considérés comme faisant partie des
surfaces des profilés.

Zahteve za kakovost površine pri dobavi vroče valjane jeklene pločevine, širokih ploščatih izdelkov in profilov – 3. del: Profili

General Information

Status
Published
Publication Date
07-Dec-2004
Withdrawal Date
29-Jun-2005
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
03-Sep-2019

Relations

Buy Standard

Standard
EN 10163-3:2005
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: SectionsConditions de livraison relatives a l'état de surface des tôles, larges plats et profilés en acier laminés a chaud - Partie 3: ProfilésLieferbedingungen für die Oberflächenbeschaffenheit von warmgewalzten Stahlerzeugnissen (Blech, Breitflachstahl und Profile) - Teil 3: Profile77.140.70Jekleni profiliSteel profiles77.140.50SROL]GHONLFlat steel products and semi-productsICS:SIST EN 10163-3:2005enTa slovenski standard je istoveten z:EN 10163-3:200401-februar-2005SIST EN 10163-3:2005SLOVENSKI
STANDARDSIST EN 10163-3:19971DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10163-3
December 2004 ICS 77.140.60; 77.140.70 Supersedes EN 10163-3:1991 English version
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections
Conditions de livraison relatives à l'état de surface des tôles, larges plats et profilés en acier laminés à chaud - Partie 3: Profilés
Lieferbedingungen für die Oberflächenbeschaffenheit von warmgewalzten Stahlerzeugnissen (Blech, Breitflachstahl und Profile) - Teil 3: Profile This European Standard was approved by CEN on 4 November 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10163-3:2004: E
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.