EN 10365:2017

Hot rolled steel channels, I and H sections - Dimensions and masses

This European standard specifies the nominal dimensions and masses of the hot rolled steel channels, I and H sections.
The following shapes are covered by this standard:
Sections:
-   Parallel flange I sections IPE;
-   Wide flange beams HE;
-   Extra wide flange beams HL and HLZ;
-   Wide flange columns HD;
-   Wide flange bearing piles HP and UBP;
-   Universal beams UB;
-   Universal columns UC;
-   Taper flange I sections IPN and J.
Channels:
-   Parallel flange channels UPE and PFC;
-   Taper flange channels UPN, U and CH.
These requirements do not apply to hot rolled steel channels, I and H sections from stainless steel.

Warmgewalzter U-Profilstahl, I- und H-Träger - Maße und Masse

Diese Europäische Norm legt die Maße und Masse für warmgewalzte U-Profile, I und H Träger aus Stahl fest.
Diese Norm gilt für folgende Produkte:
Träger:
-   I-Träger mit parallelen Flanschflächen, IPE-Reihe
-   Breite I-Träger mit parallelen Flanschflächen, HE-Reihe
-   Breite I-Träger mit besonders breiten Flanschen, HL und HLZ-Reihe
-   Breite I-Träger, Breitflansch und Stützenprofile, HD-Reihe
-   Breite I-Träger mit gleicher Dicke für Flansche und Steg, HP und UBP-Reihe
-   Universal I-Träger, UB-Reihe
-   Universal I-Träger, UC-Reihe
-   I-Träger mit geneigten inneren Flanschflächen, IPN und J-Reihe
U-Profile:
-   U-Profile mit parallelen Flanschflächen, UPE und PFC-Reihe
-   U-Profile mit geneigten inneren Flanschflächen, UPN, U und CH-Reihe.
Die Festlegungen dieser Norm gelten nicht für warmgewalzte U-Profile, I und H Träger aus nicht rostendem Stahl.

Profilés en U en aciers laminés à chaud, poutrelles I et H - Dimensions et masses

Cette norme européenne spécifie les dimensions et masses nominales des profilés en U en aciers laminés à chaud, et des poutrelles I et H.
Les formes suivantes sont couvertes par cette norme :
Poutrelles :
-   Poutrelles en I à ailes parallèles IPE
-   Poutrelles à larges ailes HE
-   Poutrelles à très larges ailes HL et HLZ
-   Poutrelles-poteaux à large ailes HD
-   Poutrelles-pieux à larges ailes HP and UBP
-   Poutrelles universelles UB
-   Poutrelles-poteaux universelles UC
-   Poutrelles en I à ailes inclinées IPN and J
Profilés :
-   Profils en U à ailes parallèles UPE et PFC
-   Profils en U à ailes inclinées UPN, U and CH
Ces exigences ne s'appliquent ni aux profilés en U en acier laminés à chaud ni aux poutrelles I et H en acier inoxydable.

Vroče valjani jekleni profili I in H - Mere in mase

Ta evropski standard določa nazivne mere in mase vroče valjanih jeklenih profilov, prerezov I in H.
Ta evropski standard zajema naslednje oblike:
Prerezi:
– vzporedna prirobnica I IPE
– široki nosilci prirobnice HE
– izjemno široki nosilci prirobnice HL
– široki stebri prirobnice HD
– široki nosilni piloti prirobnice HP in UBP
– univerzalni nosilci UB
– univerzalni stebri UC
– konična prirobnica IPN in J
Profili:
– vzporedni profili prirobnice UPE in PFC
– konični profili prirobnice UPN, U in CH
Te zahteve ne veljajo za vroče valjane jeklene profile, prereza I in H iz nerjavnega jekla.

General Information

• Status: Published
• Publication Date: 17-Jan-2017
• Withdrawal Date: 30-Jul-2017
• ICS: 77.140.70 - Steel profiles
• Technical Committee: ECISS/TC 103 - Structural steels other than reinforcements
• Drafting Committee: ECISS/TC 103/WG 5 - Hot rolled steel channels, I and H sections
• Current Stage: 9092 - Decision on results of review/2YR ENQ - revise - Review Enquiry
• Completion Date: 03-Sep-2022
• Ref Project: SIST EN 10365:2017 - Hot rolled steel channels, I and H sections - Dimensions and masses

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgewalzter U-Profilstahl, I und H Träger - Maße und MasseProfilés en U en aciers laminés à chaud, poutrelles I et H - Dimensions, masses et propriétés des profilésHot rolled steel channels, I and H sections - Dimensions and masses77.140.70Jekleni profiliSteel profilesICS:Ta slovenski standard je istoveten z:EN 10365:2017SIST EN 10365:2017en,fr,de01-marec-2017SIST EN 10365:2017SLOVENSKI
STANDARD



SIST EN 10365:2017



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10365
January
t r s y ICS
y yä s v rä y r English Version
Hot rolled steel channelsá I and H sections æ Dimensions and masses Profilßs en U en aciers laminßs à chaudá poutrelles I et H æ Dimensions et masses
Warmgewalzter UæProfilstahlá Iæ und HæTräger æ Maße und Masse This European Standard was approved by CEN on
s v November
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r u x wã t r s y ESIST EN 10365:2017



EN 10365:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 5 4 Designation. 5 5 Dimensions and masses . 5 6 Tolerances on dimensions, shape and mass . 7 7 Material . 7 Annex A (informative)
Comparison of symbols used in this document with those in EN 1993-1-1 . 32 Bibliography . 33
SIST EN 10365:2017



EN 10365:2017 (E) 3 European foreword This document (EN 10365:2017) has been prepared by Technical Committee ECISS/TC 103 “Structural steels other than reinforcements”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be withdrawn at the latest by July 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This project was submitted to the Enquiry under reference prEN 16828. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
...