EN 1852-1:2018+A1:2022
(Main)Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
This part of EN 1852 specifies the requirements for solid wall pipes with smooth internal and external surfaces extruded from the same compound/formulation throughout the wall, fittings and the system of polypropylene (PP) piping systems intended for use for:
- non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and
- non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
This standard covers PP materials without mineral modifiers.
It also specifies the test parameters for the test methods referred to in this standard.
NOTE 1 Solid wall multilayer pipes with different formulation throughout the wall and foamed core pipes are covered by EN 13476-2 [1] (see also CEN ISO/TR 27165 [2]).
This standard covers a range of nominal sizes, and pipe series and gives recommendations concerning colours.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with CEN/TS 1852-2, it is applicable to PP pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 3 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be connected to pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 14.
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Polypropylen (PP) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem
Dieser Teil der EN 1852 legt Anforderungen an Vollwand-Rohre mit glatter Innen und Außenoberfläche, die über die gesamte Wanddicke aus der gleichen Formmasse/Zusammensetzung extrudiert wurden, Form¬stücke und das Rohrleitungssystem aus Polypropylen (PP) fest, zur Verwendung in erdverlegten drucklosen Abwasserkanälen und leitungen
— außerhalb der Gebäudestruktur (Anwendungs¬kennzeichen U) sowie
— sowohl innerhalb der Gebäudestruktur (Anwendungs¬kennzeichen D) als auch außerhalb der Gebäudestruktur.
Die Erzeugnisse werden entsprechend mit „U“ bzw. „UD“ gekennzeichnet.
Diese Norm ist anwendbar für Werkstoffe aus Polypropylen (PP) ohne mineralische Additive.
Es werden auch die Prüfparameter für die Prüfverfahren festgelegt, auf die in dieser Norm verwiesen wird.
ANMERKUNG 1 Vollwand-Mehrschichtrohre mit unterschiedlicher Zusammensetzung über die Wanddicke und geschäumte Kernrohre fallen in den Anwendungsbereich von EN 13476 2 [1] (siehe auch CEN ISO/TR 27165 [2]).
Diese Norm ist anwendbar für eine Reihe von Nennweiten und Rohrreihen und gibt Empfehlungen für die Farbgebung.
ANMERKUNG 2 Der Kunde bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Vorschriften und Verlegepraktiken bzw. -bestimmungen für die entsprechende Auswahl dieser Kriterien verantwortlich.
Zusammen mit CEN/TS 1852 2 ist dieses Dokument anwendbar für Rohre und Formstücke aus PP, ihre Verbindungen untereinander sowie Verbindungen mit Rohrleitungsteilen aus anderen Kunststoffen oder sonstigen Werkstoffen, die für erdverlegte Abwasserkanäle und -leitungen vorgesehen sind.
Die Formstücke können im Spritzguss hergestellt oder aus Rohren und/oder Spritzgussteilen handfertigt werden.
ANMERKUNG 3 Rohre, Formstücke oder andere Rohrleitungsteile, die einer der in Anhang C aufgeführten Kunststoff-Produktnormen entsprechen, können mit Rohren und Formstücken nach dieser Norm verbunden werden, sofern sie die Anforderungen an die Maße der Verbindungen nach Abschnitt 6 sowie die Anforderungen nach Tabelle 14 erfüllen.
Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène (PP) - Partie 1: Spécifications pour tubes, raccords et le système
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 1. del: Specifikacije za cevi, fitinge in sistem (vključno z dopolnilom A1)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2022
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 1. del:
Specifikacije za cevi, fitinge in sistem (vključno z dopolnilom A1)
Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Polypropylen (PP) - Teil 1: Anforderungen an Rohre, Formstücke und das
Rohrleitungssystem
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement enterrés sans pression - Polypropylène (PP) - Partie 1: Spécifications
pour tubes, raccords et le système
Ta slovenski standard je istoveten z: EN 1852-1:2018+A1:2022
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 1852-1:2018+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2022
EUROPÄISCHE NORM
ICS 23.040.05 Supersedes EN 1852-1:2018
English Version
Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene (PP) - Part 1:
Specifications for pipes, fittings and the system
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -
enterrés sans pression - Polypropylène (PP) - Partie 1: Polypropylen (PP) - Teil 1: Anforderungen an Rohre,
Spécifications pour tubes, raccords et le système Formstücke und das Rohrleitungssystem
This European Standard was approved by CEN on 20 November 2017 and includes Amendment 1 approved by CEN on 28 June
2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1852-1:2018+A1:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Symbols and abbreviations . 9
4.1 Symbols . 9
4.2 Abbreviations . 10
5 Material . 10
5.1 PP final compound . 10
5.2 Utilization of non-virgin material . 10
5.3 Melt mass-flow rate . 10
5.4 Resistance to internal pressure . 11
5.5 Thermal stability (OIT) . 11
5.6 Sealing ring retaining means . 11
6 General characteristics . 12
6.1 Appearance . 12
6.2 Colour . 12
7 Geometrical characteristics . 12
7.1 General . 12
7.2 Dimensions of pipes . 12
7.2.1 Outside diameters . 12
7.2.2 Outside diameters with close tolerances (CT) . 13
7.2.3 Length of pipes . 14
7.2.4 Chamfering . 15
7.2.5 Wall thicknesses . 15
7.3 Dimensions of fittings . 16
7.3.1 Outside diameters . 16
7.3.2 Design lengths . 16
7.3.3 Wall thicknesses . 17
7.4 Dimensions of sockets and spigots . 18
7.4.1 Diameters and lengths of elastomeric ring seal sockets and spigots . 18
7.4.2 Wall thicknesses of sockets . 21
7.5 Types of fittings . 22
8 Mechanical characteristics . 25
8.1 Mechanical characteristics of pipes. 25
8.1.1 General requirements . 25
8.1.2 Additional mechanical requirements . 26
8.2 Mechanical characteristics of fittings . 27
9 Physical characteristics . 28
9.1 Physical characteristics of pipes. 28
9.2 Physical characteristics of fittings . 29
10 Performance requirements . 30
11 Sealing rings . 31
12 Marking . 31
12.1 General . 31
12.2 Minimum required marking of pipes . 31
12.3 Minimum required marking of fittings . 32
12.4 Additional marking . 33
Annex A (normative) Utilization of non-virgin PP material . 34
A.1 Own reprocessed material from pipes and fittings . 34
A.2 External reprocessed and recycled materials with an agreed specification . 34
A.2.1 Material from PP pipes and fittings . 34
A.2.2 Material from PP products other than pipes and fittings . 35
Annex B (informative) General characteristics of PP pipes and fittings . 36
B.1 General . 36
B.2 Material characteristics . 36
B.3 Ring stiffness . 36
B.4 Chemical resistance . 37
B.5 Abrasion resistance . 37
B.6 Hydraulic roughness . 37
B.7 Diametric deflection . 37
Annex C (informative) Product standards of components that can be connected to
components conforming to this standard . 38
Bibliography . 39
European foreword
This document (EN 1852-1:2018+A1:2022) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2023, and conflicting national standards shall be
withdrawn at the latest by April 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1 approved by CEN on 28 June 2022.
The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ".
!This document supersedes EN 1852-1:2018."
The System Standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes,
fittings and valves for the transport
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.