CEN/TS 13598-3:2021

Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Assessment of conformity

This document gives guidance for requirements for the assessment of conformity of materials (compounds/formulations), products, joints and assemblies in accordance with the applicable part(s) of EN 13598-1 and EN 13598-2 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1   The quality management system is expected to conform to or be no less stringent than the relevant requirements of EN ISO 9001 [1].
NOTE 2   If certification is involved, the certification body is expected to be compliant with EN ISO/IEC 17065 [5].
NOTE 3   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 13598-1 and EN 13598-2 (see Foreword) this document is applicable to ancillary fittings including shallow chambers and manholes and inspection chambers.

Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 3: Beurteilung der Konformität

Dieses Dokument enthält einen Leitfaden für Anforderungen für die Beurteilung der Konformität von Werkstoffen (Formmassen/Zusammensetzungen), Erzeugnissen, Verbindungen und Bauteilkombinationen nach dem/den jeweils anwendbaren Teil(en) von EN 13598 1 und EN 13598 2, die als Bestandteil des Qualitätsmanagementsystems im Qualitätssicherungsplan des Herstellers und für die Ein¬führung von Zertifizierungsverfahren vorgesehen sind.
ANMERKUNG 1   Es wird davon ausgegangen, dass das Qualitätsmanagementsystem EN ISO 9001 [1] oder mindestens ebenso strengen Anforderungen entspricht.
ANMERKUNG 2   Wenn eine Zertifizierung enthalten ist, wird davon ausgegangen, dass die Zertifizierungsstelle nach EN ISO/IEC 17065 [5] zugelassen ist.
ANMERKUNG 3   Anhang A enthält in Form einer Matrix der grundlegenden Prüfungen einen Überblick über das Prüfschema.
In Verbindung mit EN 13598 1 und EN 13598 2 (siehe Vorwort) ist dieses Dokument anwendbar für Zubehörteile einschließlich Schächte mit geringer Einbautiefe, Einsteigschächte und Kontrollschächte.

Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVCU), polypropylène (PP) et polyéthylène (PE) - Partie 3: Évalution de la conformité

Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Nemehčan polivinilklorid (PVC-U), polipropilen (PP) in polietilen (PE) - 3. del: Ugotavljanje skladnosti

Ta tehnična specifikacija vsebuje navodila za ugotavljanje skladnosti spojin/formulacij, izdelkov in sestavov s 1. in 2. delom standarda EN 13598, pri čemer naj bi se te informacije vključile v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti in za vzpostavitev postopka certificiranja, ki ga izvajajo tretje osebe.
OPOMBA:   V pomoč bralcem dodatka A in B vsebujeta osnovno preskusno matriko.
Ta tehnična specifikacija se v povezavi s standardoma EN 13598-1 in EN 13598-2 uporablja za pomožne fitinge za odvodnjavanje, ki so položeni v zemljo, vključno z jaški in revizijskimi komorami:
–   za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo zunaj stavbne konstrukcije (koda območja uporabe »U«), kar je na izdelkih označeno z »U«; in
–   za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo znotraj stavbne konstrukcije (koda območja uporabe »D«) ali zunaj nje (koda območja uporabe »U«), kar je na izdelkih označeno z »UD«.

General Information

• Status: Published
• Publication Date: 23-Nov-2021
• ICS: 23.040.05 - Pipeline and its parts for external sewage systems
• ICS: 93.030 - External sewage systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 20 - Thermoplastics ancillaries for soil and waste discharge and gravity buried drainage and sewerage systems
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 24-Nov-2021
• Due Date: 07-Nov-2022
• Completion Date: 24-Nov-2021
• Ref Project: SIST-TS CEN/TS 13598-3:2022 - Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Assessment of conformity

Relations

• Replaces: CEN/TS 13598-3:2012 - Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride)(PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Guidance for assessment of conformity
• Effective Date: 01-Dec-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2022
Nadomešča:
SIST-TS CEN/TS 13598-3:2012
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Nemehčan polivinilklorid (PVC-
U), polipropilen (PP) in polietilen (PE) - 3. del: Ugotavljanje skladnosti
Plastics piping systems for non-pressure underground drainage and sewerage -
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) -
Part 3: Assessment of conformity
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und
Polyethylen (PE) - Teil 3: Empfehlungen für die Beurteilung der Konformität
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVCU),
polypropylène (PP) et polyéthylène (PE) - Partie 3: Évalution de la conformité
Ta slovenski standard je istoveten z: CEN/TS 13598-3:2021
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

CEN/TS 13598-3
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
November 2021
TECHNISCHE SPEZIFIKATION
ICS 93.030; 23.040.05 Supersedes CEN/TS 13598-3:2012
English Version
Plastics piping systems for non-pressure underground
drainage and sewerage - Unplasticized poly(vinyl chloride)
(PVC-U), polypropylene (PP) and polyethylene (PE) - Part
3: Assessment of conformity
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -
enterrés sans pression - Poly(chlorure de vinyle) non Weichmacherfreies Polyvinylchlorid (PVC-U),
plastifié (PVCU), polypropylène (PP) et polyéthylène Polypropylen (PP) und Polyethylen (PE) - Teil 3:
(PE) - Partie 3: Évalution de la conformité Empfehlungen für die Beurteilung der Konformität
This Technical Specification (CEN/TS) was approved by CEN on 17 October 2021 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 13598-3:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Abbreviated terms and symbols . 9
5 General . 9
6 Testing (EN 13598-1) . 9
6.1 Group . 9
6.1.1 General . 9
6.1.2 Size groups . 9
6.1.3 Fitting groups . 10
6.2 Type testing . 10
6.2.1 General . 10
6.2.2 Change of material – PVC-U . 11
6.2.3 Change of material - Polypropylene . 12
6.2.4 Change of material - Polyethylene . 13
6.3 Batch release testing . 17
6.4 Process verification testing . 19
6.5 Audit testing . 21
6.6 Test records . 23
7 Testing (EN 13598-2) . 23
7.1 Group . 23
7.1.1 General . 23
7.1.2 Size groups . 23
7.1.3 Fitting groups . 24
7.2 Type testing . 24
7.2.1 General . 24
7.2.2 Change of material – PVC-U . 25
7.2.3 Change of material - Polypropylene . 26
7.2.4 Change of material - Polyethylene . 27
7.3 Batch release testing . 32
7.4 Process verification testing . 34
7.5 Audit testing . 36
7.6 Test records . 38
Annex A (informative)  Basic test matrix . 39
Bibliography . 43
European foreword
This document (CEN/TS 13598-3:2021) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN/TS 13598-3:2012.
Compared with CEN/TS 13598-3:2012, the following changes have been made:
— this document has been updated to comply with the latest CEN/TC 155 internal guide – Plastics
piping systems – Template for documents for the assessment of conformity;
— type testing clauses have been updated to clarify what constitutes a change of material. Examples of
a change of design, production processing method, extension of product range and system are also
given;
— the applicable characteristics for assessment of conformity testing are now listed under separate
Clauses 6 and 7 for EN 13598 parts 1 and 2 respectively;
— the tables in Clauses 6 and 7 have been updated to align the content and references with
EN 13598-1:2020 and EN 13598-2:2020.
EN 13598 consists of the following Parts under the general title Plastics piping systems for non-pressure
underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and
polyethylene (PE):
— Part 1: Specifications for ancillary fittings and shallow chambers;
— Part 2: Specifications for manholes and inspection chambers;
— Part 3: Guidance for assessment of conformity (the present document).
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
This document details the applicable characteristics to be assessed for type testing (TT), batch release
test (BRT), process verification test (PVT), and audit test (AT), as well as the frequency and sampling for
testing.
This document has been prepared using the latest CEN/TC155/WG21 assessment of conformity template
N1089.
The concept of testing and organization of those tests used for the assessment of conformity is shown,
without or with certification, in Figures 1 and 2.

Figure 1 — Typical scheme for the assessment of conformity by a manufacturer, without
certification
Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including
certification
1 Scope
This document gives guidance for requirements for the assessment of conformity of materials
(compounds/formulations), products, joints and assemblies in accordance with the applicable part(s) of
EN 13598-1 and EN 13598-2 intended to be included in the manufacturer’s quality plan as part of the
quality management system and for the establishment of certification procedures.
NOTE 1 The quality management system is expected to conform to or be no less stringent than the relevant
requirements of EN ISO 9001 [1].
NOTE 2 If certification is involved, the certification body is expected to be compliant with EN ISO/IEC 17065 [5].
NOTE 3 A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 13598-1 and EN 13598-2 (see Foreword) this document is applicable to ancillary
fittings including shallow chambers and manholes and inspection chambers.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 13598-1:2020, Plastics piping systems for non-pressure underground drainage and sewerage -
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications
for ancil
...