EN ISO 13706:2005
(Main)Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers (ISO 13706:2005)
Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers (ISO 13706:2005)
ISO 13706:2005 gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum and natural gas industries.
ISO 13706:2005 is applicable to air-cooled heat exchangers with horizontal bundles, but the basic concepts can also be applied to other configurations.
Erdöl-, petrochemische und Erdgasindustrie - Luftgekühlte Wärmeaustauscher (ISO 13706:2005)
Industries du pétrole, de la pétrochimie et du gaz naturel - Echangeurs de chaleur refroidis à l'air (ISO 13706:2005)
Petrokemična industrija ter industrija za predelavo nafte in zemeljskega plina – Zračno hlajeni prenosniki toplote (ISO 13706:2005)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Erdöl-, petrochemische und Erdgasindustrie - Luftgekühlte Wärmeaustauscher (ISO 13706:2005)Industries du pétrole, de la pétrochimie et du gaz naturel - Echangeurs de chaleur refroidis a l'air (ISO 13706:2005)Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers (ISO 13706:2005)75.180.20Predelovalna opremaProcessing equipment71.120.30Prenosniki toploteHeat exchangersICS:Ta slovenski standard je istoveten z:EN ISO 13706:2005SIST EN ISO 13706:2006en,fr01-julij-2006SIST EN ISO 13706:2006SLOVENSKI
STANDARDSIST EN ISO 13706:20001DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 13706October 2005ICS 75.180.20; 27.060.30Supersedes EN ISO 13706:2000
English VersionPetroleum, petrochemical and natural gas industries - Air-cooledheat exchangers (ISO 13706:2005)Industries du pétrole, de la pétrochimie et du gaz naturel -Echangeurs de chaleur refroidis à l'air (ISO 13706:2005)Erdöl- und Erdgasindustrien - Luftgekühlte Wärmetauscher(ISO 13706:2005)This European Standard was approved by CEN on 30 September 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 13706:2005: ESIST EN ISO 13706:2006
Foreword
This document (EN ISO 13706:2005) has been prepared by Technical Committee ISO/TC 67 "Materials, equipment and offshore structures for petroleum and natural gas industries" in collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore structures for petroleum and natural gas industries", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2006, and conflicting national standards shall be withdrawn at the latest by April 2006.
This document supersedes EN ISO 13706:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 13706:2005 has been approved by CEN as EN ISO 13706:2005 without any modifications.
Reference numberISO 13706:2005(E)© ISO 2005
INTERNATIONAL STANDARD ISO13706Second edition2005-10-15Petroleum, petrochemical and natural gas industries — Air-cooled heat exchangersIndustries du pétrole, de la pétrochimie et du gaz naturel — Échangeurs de chaleur refroidis à l'air
ISO 13706:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2005 – All rights reserved
ISO 13706:2005(E) © ISO 2005 – All rights reserved iiiContents Page Foreword.v Introduction.vi 1 Scope.1 2 Normative references.1 3 Terms and definitions.2 4 General.4 5 Proposals.5 6 Documentation.5 6.1 Approval information.5 6.2 Final records.6 7 Design.7 7.1 Tube bundle design.7 7.2 Air-side design.19 7.3 Structural design.30 8 Materials.35 8.1 General.35 8.2 Headers.36 8.3 Louvres.36 8.4 Other components.36 9 Fabrication of tube bundle.37 9.1 Welding.37 9.2 Post-weld heat treatment.37 9.3 Tube-to-tubesheet joints.37 9.4 Gasket contact surfaces.39 9.5 Thread lubrication.39 9.6 Alignment and tolerances.39 9.7 Assembly.39 10 Inspection, examination and testing.41 10.1 Quality control.41 10.2 Pressure test.42 10.3 Shop run-in.42 10.4 Equipment performance testing.42 10.5 Nameplates.42 11 Preparation for shipment.42 11.1 General.42 11.2 Surfaces and finishes.43 11.3 Identification and notification.43 12 Supplemental requirements.43 12.1 General.43 12.2 Design.43 12.3 Examination.44 12.4 Testing.44 Annex A (informative)
Recommended practices.45 Annex B (informative)
Checklist, data sheets and electronic data exchange.49 SIST EN ISO 13706:2006
ISO 13706:2005(E) iv © ISO 2005 – All rights reserved Annex C (informative)
Winterization of air-cooled heat exchangers.66 Bibliography.115
ISO 13706:2005(E) © ISO 2005 – All rights reserved vForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13706 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and systems. This second edition cancels and replaces the first edition (ISO 13706:2000), which has been technically revised. SIST EN ISO 13706:2006
ISO 13706:2005(E) vi © ISO 2005 – All rights reserved Introduction Users of this International Standard should be aware that further or differing requirements may be needed for individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser from accepting, alternative equipment or engineering solutions for the individual application. This may be particularly applicable where there is innovative or developing technology. Where an alternative is offered, the vendor should identify any variations from this International Standard and provide details.
INTERNATIONAL STANDARD ISO 13706:2005(E) © ISO 2005 – All
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.