EN ISO 15547-1:2005
(Main)Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 1: Plate-and-frame heat exchangers (ISO 15547-1:2005)
Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 1: Plate-and-frame heat exchangers (ISO 15547-1:2005)
ISO 15547-1:2005 gives requirements and recommendations for the mechanical design, materials selection, fabrication, inspection, testing, and preparation for shipment of plate-and-frame heat exchangers for use in petroleum, petrochemical and natural gas industries. It is applicable to gasketed, semi-welded and welded plate-and-frame heat exchangers.
Erdöl-, petrochemische und Erdgasindustrie - Plattenwärmetauscher - Teil 1: Plattenwärmeaustauscher (ISO 15547-1:2005)
Industries du pétrole, de la pétrochimie et du gaz naturel - Echangeurs thermiques à plaques - Partie 1: Echangeurs thermiques à plaques et cadre (ISO 15547-1:2005)
Petrokemična industrija ter industrija za predelavo nafte in zemeljskega plina – Ploščni prenosniki toplote – 1. del: Prenosniki toplote s ploščo in ogrodjem (ISO 15547-1:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2006
1DGRPHãþD
SIST EN ISO 15547:2002
3HWURNHPLþQDLQGXVWULMDWHULQGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD±
3ORãþQLSUHQRVQLNLWRSORWH±GHO 3UHQRVQLNLWRSORWHVSORãþRLQRJURGMHP ,62
Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part
1: Plate-and-frame heat exchangers (ISO 15547-1:2005)
Erdöl-, petrochemische und Erdgasindustrie - Plattenwärmetauscher - Teil 1:
Plattenwärmeaustauscher (ISO 15547-1:2005)
Industries du pétrole, de la pétrochimie et du gaz naturel - Echangeurs thermiques a
plaques - Partie 1: Echangeurs thermiques a plaques et cadre (ISO 15547-1:2005)
Ta slovenski standard je istoveten z: EN ISO 15547-1:2005
ICS:
71.120.30 Prenosniki toplote Heat exchangers
75.180.20 Predelovalna oprema Processing equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 15547-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2005
ICS 75.180.20; 27.060.30 Supersedes EN ISO 15547:2001
English Version
Petroleum, petrochemical and natural gas industries - Plate-type
heat exchangers - Part 1: Plate-and-frame heat exchangers
(ISO 15547-1:2005)
Industries du pétrole, de la pétrochimie et du gaz naturel - Erdöl-, petrochemische und Erdgasindustrie -
Echangeurs thermiques à plaques - Partie 1: Echangeurs Plattenwärmetauscher - Teil 1: Plattenwärmetauscher (ISO
thermiques à plaques et cadre (ISO 15547-1:2005) 15547-1:2005)
This European Standard was approved by CEN on 28 October 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15547-1:2005: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 15547-1:2005) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum, petrochemical and natural gas industries", the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2006, and conflicting national standards
shall be withdrawn at the latest by May 2006.
This document supersedes EN ISO 15547:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 15547-1:2005 has been approved by CEN as EN ISO 15547-1:2005 without any
modifications.
INTERNATIONAL ISO
STANDARD 15547-1
First edition
2005-11-01
Petroleum, petrochemical and natural gas
industries — Plate-type heat
exchangers —
Part 1:
Plate-and-frame heat exchangers
Industries du pétrole, de la pétrochimie et du gaz naturel — Échangeurs
thermiques à plaques —
Partie 1: Échangeurs thermiques à plaques et cadre
Reference number
ISO 15547-1:2005(E)
©
ISO 2005
ISO 15547-1:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
ISO 15547-1:2005(E)
Contents Page
Foreword. iv
Introduction . iv
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 General.4
5 Proposal information required .4
6 Drawings and other data requirements.5
7 Design .6
8 Materials .12
9 Fabrication.13
10 Inspection and testing.13
11 Preparation for shipment .14
Annex A (informative) Recommended practice .15
Annex B (informative) Plate-and-frame heat exchanger checklist.18
Annex C (informative) Plate-and-frame heat exchanger data sheets .19
Bibliography .26
ISO 15547-1:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15547-1 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and
systems.
This first edition of ISO 15547-1, together with ISO 15547-2, cancels and replaces ISO 15547:2000, of which
it constitutes a technical revision.
ISO 15547 consists of the following parts, under the general title Petroleum, petrochemical and natural gas
industries — Plate-type heat exchangers:
⎯ Part 1: Plate-and-frame heat exchangers
⎯ Part 2: Brazed aluminium plate-fin heat exchangers
iv © ISO 2005 – All rights reserved
ISO 15547-1:2005(E)
Introduction
Users of this part of ISO 15547 should be aware that further or differing requirements may be needed for
individual applications. This part of ISO 15547 is not intended to inhibit a vendor from offering, or the
purchaser from accepting, alternative equipment or engineering solutions for the individual application. This
may be particularly applicable where there is an innovative or developing technology. Where an alternative is
offered, the vendor should identify any variations from this part of ISO 15547 and provide details.
This part of ISO 15547 requires the purchaser to specify certain details and features.
A bullet (z) at the beginning of a clause or subclause indicates a requirement for the purchaser to make a
decision or provide information (for information, a checklist is provided in Annex B).
In this part of ISO 15547, where practical, US Customary units are included in parentheses for information.
INTERNATIONAL STANDARD ISO 15547-1:2005(E)
Petroleum, petrochemical and natural gas industries —
Plate-type heat exchangers —
Part 1:
Plate-and-frame heat exchangers
1 Scope
This part of ISO 15547 gives requirements and recommendations for the mechanical design, materials
selection, fabrication, inspection, testing, and preparation for shipment of plate-and-frame heat exchangers for
use in petroleum, petrochemical and natural gas industries. It is applicable to gasketed, semi-welded and
welded plate-and-frame heat exchangers.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 8501-1, Preparation of steel substrates before application of paints and related products — Visual
assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel
substrates and of steel substrates after overall removal of previous coatings
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
drip tray
tray that is able to collect droplets from an entire heat exchanger plate pack
3.2
end plate
plate which prevent the fluids in a plate-and-frame heat exchanger from contacting the fixed and removable
covers
NOTE There are two end plates, one at each end of the plate-and-frame heat exchanger.
3.3
frame
assembly that provides the structural support and pressure containment of a plate-and-frame heat exchanger
3.4
welded plate pack
plate pack where the gaskets have been replaced by welds
ISO 15547-1:2005(E)
3.5
heat transfer area
sum of the surface areas of one side of all plates in contact with both heat-transfer fluids
NOTE Areas of end plates are not included.
3.6
item number
purchaser’s identification number for a plate-and-frame heat exchanger
3.7
minimum design metal temperature
lowest metal temperature at which pressure-containing elements can be subjected to design pressure
EXAMPLE Ambient temperature, process fluid temperature.
3.8
pass plate
plate used to change the direction of flow of a stream in a plate-and-frame heat exchanger with two or more
passes
3.9
plate
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.