prEN 1759-3
(Main)Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 3: Copper alloy flanges
Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 3: Copper alloy flanges
This European Standard specifies requirements for circular copper alloy flanges and copper alloy collars combined with loose steel plate flanges in Class designations Class 150 and Class 300 and nominal sizes from DN 10 to DN 900 (NPS ½ to NPS 36) in the types shown in Table 1.
This standard also specifies dimensions and tolerances, materials and their associated pressure/temperature (p/T) ratings, flange facings and related surface finish, weld repairs and marking together with information on bolting, gaskets, application and installation and approximate flange masses.
The flanges specified, with the exception of integral (type 21) flanges, are for attachment to copper or copper alloy tubes in accordance with EN 12449.
NOTE 1 The size of copper and copper alloy tubes is designated by reference to the outside diameter in millimetres.
NOTE 2 See also Annex B.
NOTE 3 Non-gasketed pipe joints are outside the scope of this standard.
Table 1 - Types of flanges and collars [Table 1 and Figure 1 not represented]
Flansche und ihre Verbindungen - Runde Flansche für Rohre, Armaturen, Formstücke und Zubehörteile, nach Class bezeichnet - Teil 3: Flansche aus Kupferlegierungen
Dieses Dokument Norm legt Anforderungen fest für runde Flansche aus Kupferlegierungen und glatte Losflansche aus Stahl kombiniert mit Bunden aus Kupferlegierungen mit den Class-Stufen Class 150 und Class 300 und den Nennweiten DN 10 bis DN 900 (NPS 1/2 bis NPS 36) der Typen nach Tabelle 1.
Dieses Dokument legt auch Maße und Toleranzen, Werkstoffe und zugehörige Druck/Temperatur-Zuordnungen, Flanschdichtflächen und deren Oberflächenbeschaffenheit, Reparatur durch Schweißen, Kennzeichnung und Qualitätssicherung fest und enthält Angaben zu Schrauben und Muttern, Dichtungen, Anwendung, Montage und ungefähre Flanschgewichte.
Die festgelegten Flansche, ausgenommen Integralflansche (Typ 21), werden zur Befestigung an Rohren aus Kupfer oder Kupferlegierungen nach EN 12449 verwendet.
ANMERKUNG 1 Die Größe von Rohren aus Kupfer und Kupferlegierungen wird durch Angabe des Außendurchmessers in Millimeter bezeichnet.
ANMERKUNG 2 Siehe auch Anhang B.
ANMERKUNG 3 Rohrleitungsverbindungen ohne Dichtung liegen nicht im Anwendungsbereich dieses Dokuments.
Tabelle 1 - Typen von Flanschen und Bunden
[...]
Bild 1 - Typen der Flansche und Bunde
Brides et leurs assemblages - Brides circulaires pour tubes, appareils de robinetterie, raccords et accessoires, désignées Class - Partie 3 : Brides en alliages de cuivre
Le présent document spécifie les prescriptions des brides circulaires en alliages de cuivre et des collets en alliages de cuivre combinés avec des brides plates tournantes en acier désignées Class 150 et Class 300 et de diamètres nominaux DN 10 à DN 900 (NPS 1/2 à NPS 36) pour les types de brides et de collets présentés au Tableau 1.
Le présent document spécifie aussi les dimensions et tolérances, les matériaux associés à leurs relations pression/température (p/T), l'état de surface des portées de joints, les réparations par soudage, le marquage avec des informations sur la boulonnerie, les joints, leur application et leur installation ainsi que les masses approximatives des brides.
Les brides spécifiées, à l'exception des brides incorporées (type 21), sont à monter sur des tubes en cuivre ou en alliages de cuivre conformément à l’EN 12449.
NOTE 1 Les dimensions des tubes de cuivre ou d'alliage de cuivre sont désignées par le diamètre extérieur en millimètres.
NOTE 2 Voir aussi Annexe B.
NOTE 3 Les raccordements sans joint de tuyauteries sont en dehors du domaine d’application du présent document.
Tableau 1 - Types de brides et de collets
[...]
Figure 1 - Types de brides et de collets
Prirobnice in prirobnični spoji - Okrogle prirobnice za cevi, ventile, fitinge in pribor z oznako Class - 3. del: Prirobnice iz bakrovih zlitin
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2022
Prirobnice in prirobnični spoji - Okrogle prirobnice za cevi, ventile, fitinge in pribor
z oznako Class - 3. del: Prirobnice iz bakrovih zlitin
Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories,
Class designated - Part 3: Copper alloy flanges
Flansche und ihre Verbindungen - Runde Flansche für Rohre, Armaturen, Formstücke
und Zubehörteile, nach Class bezeichnet - Teil 3: Flansche aus Kupferlegierungen
Brides et leurs assemblages - Brides circulaires pour tubes, appareils de robinetterie,
raccords et accessoires, désignées Class - Partie 3 : Brides en alliages de cuivre
Ta slovenski standard je istoveten z: prEN 1759-3
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2021
ICS 23.040.60 Will supersede EN 1759-3:2003
English Version
Flanges and their joints - Circular flanges for pipes, valves,
fittings and accessories, Class designated - Part 3: Copper
alloy flanges
Brides et leurs assemblages - Brides circulaires pour Flansche und ihre Verbindungen - Runde Flansche für
tubes, appareils de robinetterie, raccords et Rohre, Armaturen, Formstücke und Zubehörteile, nach
accessoires, désignées Class - Partie 3 : Brides en Class bezeichnet - Teil 3: Flansche aus
alliages de cuivre Kupferlegierungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 74.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1759-3:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 8
3 Terms and definitions . 8
4 Designation . 9
4.1 General. 9
4.2 Standard designation . 9
4.3 Information to be supplied by the equipment manufacturer . 10
5 General requirements . 10
5.1 Materials . 10
5.2 Repairs . 10
5.3 Bolting . 11
5.4 Gaskets . 11
5.5 Pressure/temperature (p/T) ratings. 11
5.5.1 General. 11
5.5.2 p/T ratings of flanged joints . 11
5.6 Dimensions. 12
5.6.1 Flanges . 12
5.6.2 Bolt holes . 12
5.7 Flange facings . 12
5.7.1 Types of facings . 12
5.7.2 Jointing face finish . 12
5.7.3 Rims . 13
5.7.4 Collars and loose flanges . 13
5.8 Spot facing or back facing . 13
5.9 Tolerances . 13
5.10 Marking . 13
5.10.1 Other than type 21 flanges . 13
5.10.2 Method of marking . 14
5.10.3 Omission of markings . 14
5.10.4 Declaration of compliance . 14
Annex A (informative) Information to be supplied by the equipment manufacturer . 29
Annex B (informative) Application and installation . 30
Annex C (informative) Use of metric bolting in lieu of imperial bolting . 31
C.1 General. 31
C.2 Gaskets . 31
C.3 Comparable nominal bolt sizes . 31
C.4 Imperial/metric bolt comparisons . 31
Annex D (informative) Approximate masses of flanges and collars . 33
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/68/EU aimed to be covered . 38
Bibliography . 40
European foreword
This document (prEN 1759-3:2021) has been prepared by Technical Committee CEN/TC 74 “Flanges
and their joints”, the secretariat of which is held by DIN.
This document is currently submitted to CEN Enquiry.
This document will supersede EN 1759-3:2003 and EN 1759-3:2003/AC:2004.
The main changes compared to EN 1759-3:2003 and EN 1759-3:2003/AC:2004 are:
— update of Annex ZA.
This document has been prepared under a standardization request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of
EU Directive(s) .
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
EN 1759 consists of the following parts:
— Flanges and their joint — Circular flanges for pipes, valves, fittings and accessories, Class
designated — Part 1: Steel flanges (draft stage;
— Flanges and their joint — Circular flanges for pipes, valves, fittings and accessories, Class
designated — Part 3: Copper alloy flanges (draft stage);
— Flanges and their joint — Circular flanges for pipes, valves, fittings and accessories, Class
designated — Part 4: Aluminium alloy flanges (draft stage).
The Annexes A, B, C, D and ZA are informative.
1 Directive 97/23 EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the
Laws of the Member States concerning pressure equipment; OIEC L 181.
Introduction
This document is related, but not identical, to ISO 7005-3 in respect of flanges having designations
Class 150 and Class 300. Outside diameters and mating dimensions are in accordance with ANSI B16.24.
Information on the use of metric bolting in lieu of imperial bolting which can be used with these flanges
is given in an informative annex.
The mating dimensions of the flanges of this standard are compatible with Class designated flanges of
other materials in accordance with the other parts of EN 1759.
1 Scope
This document specifies requirements for circular copper alloy flanges and copper alloy collars
combined with loose steel plate flanges in Class designations Class 150 and Class 300 and nominal sizes
from DN 10 to DN 900 (NPS 1/2 to NPS 36) in the types shown in Table 1.
This document also specifies dimensions and tolerances, materials and their associated
pressure/temperature (p/T) ratings, flange facings and related surface finish, weld repairs and marking
together with information on bolting, gaskets, application and installation and approximate flange
masses.
The flanges specified, with the exception of integral (type 21) flanges, are for attachment to copper or
copper alloy tubes in accordance with EN 12449.
NOTE 1 The size of copper and copper alloy tubes is designated by reference to the outside diameter in
millimetres.
NOTE 2 See also Annex B.
NOTE 3 Non-gasketed pipe joints are outside the scope of this document.
Table 1 — Types of flanges and collars
Type No. Description
01 Plate flange in copper alloy for brazing or welding
04 Loose plate flange in steel with a weld-neck collar (type 34) in copper alloy, for welding
05 Blank flange in copper alloy
05C Blank flange in steel clad with a copper alloy jointing face
07 Loose plate flange in steel with a slip-on collar (type 37) in copper alloy, for soft soldering,
brazing or welding
11 Weld-neck flange in copper alloy for welding
12 Hubbed slip-on flange in copper alloy, for soft soldering, brazing or welding
14 Hubbed slip-on flange in copper alloy supplied with tube stops, for soft soldering, brazing
or welding
21 Integral flange in copper alloy as part of some other equipment or component
34 Weld-neck collar in copper alloy
37 Slip-on collar in copper alloy
Type 01 Type 04, 34 Type 05, 05C
Plate flange in copper alloy for Loo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.