EN 791:1995/prA2

Drill rigs - Safety

Bohrgeräte - Sicherheit

Appareils de forage - Sécurité

Vrtalna oprema - Varnost

General Information

• Status: Not Published
• ICS: 91.220 - Construction equipment
• Technical Committee: CEN/TC 151 - Construction equipment and building material machines - Safety
• Drafting Committee: CEN/TC 151/WG 3 - Drilling equipment - Safety
• Current Stage: 5060 - Closure of Vote - Formal Approval
• Start Date: 19-Nov-2008
• Completion Date: 19-Nov-2008
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 791:2000/kprA2:2008 - Drill rigs - Safety

Relations

• Merged Into: EN 791:1995+A1:2009 - Drill rigs - Safety
• Effective Date: 19-Jan-2023
• Amends: EN 791:1995 - Drill rigs - Safety
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 791:2000/kprA2:2008
01-oktober-2008
Vrtalna oprema - Varnost
Drill rigs - Safety
Bohrgeräte - Sicherheit
Appareils de forage - Sécurité
Ta slovenski standard je istoveten z: EN 791:1995/prA2
ICS:
25.080.40 Vrtalniki Drilling machines
91.220 Gradbena oprema Construction equipment
SIST EN 791:2000/kprA2:2008 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 791:2000/kprA2:2008

---------------------- Page: 2 ----------------------

SIST EN 791:2000/kprA2:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 791:1995
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
June 2008
ICS 91.220

English Version
Drill rigs - Safety
Appareils de forage - Sécurité Bohrgeräte - Sicherheit
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A2, if approved, will modify the European Standard EN 791:1995. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 791:1995/prA2:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 791:2000/kprA2:2008
EN 791:1995/prA2:2008 (E)
Contents Page
Foreword.3
1 Modification to 5.2.2, Operator's position.4
2 Modification to 7.1, Marking - Data plate.4
3 Modification to 7.4.2, Operator's instructions .4
4 Addition of a new Annex ZA.5
5 Addition of a new Annex ZB.6

2

---------------------- Page: 4 ----------------------

SIST EN 791:2000/kprA2:2008
EN 791:1995/prA2:2008 (E)
Foreword
This document (EN 791:1995/prA2:2008) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines - Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.



















3

---------------------- Page: 5 ----------------------

SIST EN 791:2000/kprA2:2008
EN 791:1995/prA2:2008 (E)
1 Modification to the Foreword
Add the following second harmonization paragraph: "For relationship with EU Directive(s), see informative
Annexes ZA and ZB, which are integral parts of this document.".
2 Modification to 5.2.2, Operator's position
th nd
In the 5 paragraph, 2 indent, replace "85 dB(A)" with "80 dB(A)".
3 Modification to 7.1, Marking - Data plate
st
In the 1 paragraph, replace "and" with "," and add "and movable platforms" after "winches" to read as follows:
"The data plates for the drill rig, its winches and movable platforms shall give at least the following
information:".
Replace the text of a) as follows: "
a) the business name and full address of the manufacturer or (where applicabl
...