Heat meters - Part 5: Initial verification tests

This European Standard specifies initial verification tests and applies to heat meters. Heat meters are instruments intended for measuring the energy which in a heat-exchange circuit is absorbed (cooling) or given up (heating) by a liquid called the heat-conveying liquid. The heat meter indicates the quantity of heat in legal units.
Electrical safety requirements are not covered by this European Standard.
Pressure safety requirements are not covered by this European Standard.
Surface mounted temperature sensors are not covered by this European Standard.
This standard covers meters for closed systems only, where the differential pressure over the thermal load is limited.

Wärmezähler - Teil 5: Ersteichung

Diese Europäische Norm legt die Ersteichung fest und gilt für Wärmezähler. Wärme¬zähler sind Geräte, die dazu dienen, die Energiemenge zu messen, die in einem Wärmetauscherkreislauf durch eine als Wärmeträgerflüssigkeit bezeichnete Flüssigkeit aufgenommen (Kühlen) oder abgegeben (Heizen) wird. Der Wärmezähler zeigt die Wärmemenge in gesetzlichen Einheiten an.
Elektrische Sicherheitsanforderungen werden in dieser Europäischen Norm nicht behandelt.
Den Druck betreffende Sicherheitsanforderungen werden in dieser Europäischen Norm nicht behandelt.
Oberflächenmontierte Temperaturfühler werden in dieser Europäischen Norm nicht behandelt.
Die vorliegende Norm behandelt ausschließlich Zähler für geschlossene Systeme, in denen der Differenz-druck am Wärmeübertrager begrenzt ist.

Compteurs d'énergie thermique - Partie 5: Essais de vérification primitive

La présente Norme européenne spécifie les essais de vérification primitive pour les compteurs d'énergie thermique. Les compteurs d'énergie thermique sont des instruments destinés à mesurer l'énergie thermique qui, dans un circuit d'échange thermique, est absorbée (refroidissement) ou cédée (chauffage) par un liquide appelé « liquide caloporteur ». Le compteur d'énergie thermique fournit la quantité d'énergie thermique en unités de mesure légales.
La présente Norme européenne ne traite pas des prescriptions de sécurité électrique.
La présente Norme européenne ne traite pas des prescriptions de sécurité relative à la pression.
La présente Norme européenne ne traite pas des sondes de température montées en surface.
La présente norme couvre les compteurs pour les systèmes fermés uniquement, où la pression différentielle dans la charge thermique est limitée.

Merilniki toplote - 5. del: Preskusi prve overitve

Ta evropski standard določa preskuse prve overitve in se uporablja za toplotne števce, tj. instrumente, ki so namenjeni za merjenje toplote, ki jo v krogotoku toplotne izmenjave absorbira (hlajenje) ali oddaja (ogrevanje) tekočina, imenovana tekočina za prenos toplote. Toplotni števec podaja toploto v predpisanih enotah. Ta evropski standard ne zajema električnih varnostnih zahtev. Ta evropski standard ne zajema tlačnih varnostnih zahtev. Ta evropski standard ne zajema površinsko nameščenih senzorjev temperature. Ta standard zajema samo števce za zaprte sisteme, kjer je diferencialni tlak nad toplotno obremenitvijo omejen.

General Information

Status
Withdrawn
Publication Date
03-Nov-2015
Withdrawal Date
12-Feb-2019
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
13-Feb-2019

RELATIONS

Buy Standard

Standard
EN 1434-5:2016
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Merilniki toplote - 5. del: Preskusi prve overitveWärmezähler - Teil 5: ErsteichungCompteurs d'énergie thermique - Partie 5 : Essais de vérification initiauxHeat meters - Part 5: Initial verification tests17.200.10Toplota. KalorimetrijaHeat. CalorimetryICS:Ta slovenski standard je istoveten z:EN 1434-5:2015SIST EN 1434-5:2016en,fr,de01-januar-2016SIST EN 1434-5:2016SLOVENSKI

STANDARDSIST EN 1434-5:20071DGRPHãþD
SIST EN 1434-5:2016
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1434-5
November
t r s w ICS
s yä t r rä s r Supersedes EN
s v u væ wã t r r yEnglish Version
Heat meters æ Part
wã Initial verification tests Compteurs d 5énergie thermique æ Partie
wã Essais de vérification primitive
Wärmezähler æ Teil
wã Ersteichung This European Standard was approved by CEN on
w September
t r s wä

egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä

translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä

CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä

EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels

t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN

s v u væ wã t r s w ESIST EN 1434-5:2016

EN 1434-5:2015 (E) 2 Contents Page European foreword ....................................................................................................................................................... 3 1 Scope .................................................................................................................................................................... 5 2 Normative references .................................................................................................................................... 5 3 Terms and definitions ................................................................................................................................... 5 4 General ................................................................................................................................................................ 5 5 Uncertainty of test equipment .................................................................................................................... 6 6 Tests to be carried out ................................................................................................................................... 6 6.1 General ................................................................................................................................................................ 6 6.2 Flow sensors ..................................................................................................................................................... 6 6.3 Temperature sensor pair ............................................................................................................................. 7 6.3.1 Error in temperature difference ................................................................................................................ 7 6.3.2 Insulation resistance ..................................................................................................................................... 7 6.3.3 Single temperature sensor for smart metering applications .......................................................... 8 6.4 Calculator ........................................................................................................................................................... 8 6.5 Calculator and temperature sensor pair ................................................................................................ 8 6.5.1 Heating and cooling applications .............................................................................................................. 8 6.5.2 Calculator with single temperature sensor for smart metering applications .......................... 9 6.6 Combined heat meter .................................................................................................................................... 9 6.7 Complete meter ............................................................................................................................................... 9 7 Documentation to be supplied ................................................................................................................... 9 Annex ZA (informative)

Relationship between this European Standard and the Essential Requirements of EU Directive 2004/22/EC, MID ............................................................................. 11

SIST EN 1434-5:2016

EN 1434-5:2015 (E) 3 European foreword This document (EN 1434-5:2015) has been prepared by Technical Committee CEN/TC 176 “Heat meters”, the secretariat of which is held by SIS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be withdrawn at the latest by May 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1434-5:2007. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. EN 1434, Heat meters consists of the following parts: — Part 1: General requirements — Part 2: Constructional requirements — Part 3: Data exchange and interfaces1) — Part 4: Pattern approval tests — Part 5: Initial verification tests — Part 6: Installation, commissioning, operational monitoring and maintenance In comparison to EN 1434-5:2007, the following changes have been made: — metrological requirements for smart metering applications are added; — additional functionalities for smart metering applications are added; — bath constructions are added; — tests for cooling applications are added; — single temperature sensor for smart metering are added; — test for bi-functional meters for change-over between heating and cooling are added. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

1) EN 1434-3 is maintained by CEN/TC 294. SIST EN 1434-5:2016

EN 1434-5:2015 (E) 4 Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 1434-5:2016

EN 1434-5:2015 (E) 5 1 Scope This European Standard specifies initial verification tests for heat meters. Heat meters are instruments intended for measuring the energy which in a heat-exchange circuit is absorbed (cooling) or given up (heating) by a liquid called the heat-conveying liquid. The heat meter indicates the quantity of heat in legal units. Electrical safety requirements are not covered by this European Standard. Pressure safety requirements are not covered by this European Standard. Surface mounted temperature sensors are not covered by this European Standard. This standard covers meters for closed systems only, where the differential pressure over the thermal load is limited. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1434-1:2015, Heat meters — Part 1: General EN 60751, Industrial platinum resistance thermometers and platinum temperature sensors (IEC 60751) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1434-1:2015 apply. 4 General Initial verification of a measuring instrument is a series of tests and visual examinations carried out to determine whether an instrument manufactured to replicate a given pattern conforms to that pattern and to regulations, and that its metrological characteristics lie within the limits of the maximum permissible errors. If the instrument passes all tests and examinations, it is given legal character by its acceptance as evidenced by stamping and/or issuance of a certificate of verification. The provisions of this standard also apply to the re-verification of heat meters. The instrument shall be tested under rated operating conditions at the extremes and midpoints of its ranges. Initial verification is divided into metrological, technical and administrative phases. In tests of a heat meter as a combined instrument, the flow sensor, the temperature sensors and the calculator shall each be tested separately. Unless otherwise stated in the certificate of pattern approval, the verification shall be carried out in accordance with this standard. NOTE Modern heat meters are mainly equipped with CMOS microprocessors with a very low power consumption, allowing battery operation. Testing and adjusting of this type of meter needs a completely different approach. Until now, almost every meter type needed its own test equipment to handle the manufacturer's specific requirements. This is a very complicated and expensive way for users of several types of meters and for initial verification institutes. The more different types of heat meters a user has installed, the more testing equipment he may need. An economical testing of several meters should be possible and an easy adaptation to the existing test bench is of great interest. SIST EN 1434-5:2016

EN 1434-5:2015 (E) 6 Since this problem came up, experts have been researching an acceptable solution to it. Details of one example of an acceptable solution are given in “Normierter Wärmezähler Adap

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.