EN ISO 3671:2023
(Main)Plastics - Aminoplastic moulding materials - Determination of volatile matter (ISO 3671:2023)
Plastics - Aminoplastic moulding materials - Determination of volatile matter (ISO 3671:2023)
This document specifies a method for the determination of volatile matter (predominantly water) in aminoplastic moulding materials, by drying in an oven.
Kunststoffe - Aminoplast-Formmassen - Bestimmung der flüchtigen Anteile (ISO 3671:2023)
Dieses Dokument legt ein Verfahren zur Bestimmung der flüchtigen Anteile (hauptsächlich Wasser) in Aminoplast-Formmassen durch Trocknen in einem Ofen fest.
Plastiques - Matières à mouler aminoplastes - Détermination des matières volatiles (ISO 3671:2023)
Le présent document spécifie une méthode pour la détermination des matières volatiles (principalement de l’eau) dans les matières à mouler aminoplastes, par séchage dans une étuve.
Polimerni materiali - Aminoplasti za oblikovanje - Določevanje hlapnih snovi (ISO 3671:2023)
Ta dokument določa metodo za določevanje hlapnih snovi (predvsem vode) v
aminoplasteh za oblikovanje s sušenjem v peči.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2023
Polimerni materiali - Aminoplasti za oblikovanje - Določevanje hlapnih snovi (ISO
3671:2023)
Plastics - Aminoplastic moulding materials - Determination of volatile matter (ISO
3671:2023)
Kunststoffe - Aminoplast-Formmassen - Bestimmung der flüchtigen Anteile (ISO
3671:2023)
Plastiques - Matières à mouler aminoplastes - Détermination des matières volatiles (ISO
3671:2023)
Ta slovenski standard je istoveten z: EN ISO 3671:2023
ICS:
83.080.10 Duromeri Thermosetting materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 3671
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2023
EUROPÄISCHE NORM
ICS 83.080.10 Supersedes EN ISO 3671:1998
English Version
Plastics - Aminoplastic moulding materials -
Determination of volatile matter (ISO 3671:2023)
Plastiques - Matières à mouler aminoplastes - Kunststoffe - Aminoplast-Formmassen - Bestimmung
Détermination des matières volatiles (ISO 3671:2023) der flüchtigen Anteile (ISO 3671:2023)
This European Standard was approved by CEN on 30 September 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3671:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 3671:2023) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2024, and conflicting national standards shall be
withdrawn at the latest by April 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3671:1998.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 3671:2023 has been approved by CEN as EN ISO 3671:2023 without any modification.
INTERNATIONAL ISO
STANDARD 3671
Second edition
2023-09
Plastics — Aminoplastic moulding
materials — Determination of volatile
matter
Plastiques — Matières à mouler aminoplastes — Détermination des
matières volatiles
Reference number
ISO 3671:2023(E)
ISO 3671:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 3671:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.