EN 28167:1992
(Main)Projections for resistance welding (8167:1989)
Projections for resistance welding (8167:1989)
Specifies the characteristics and dimensions of projections for resistance welding. Includes also the appropriate design and dimensions for tools (see annex B). The projections may be used on either hot-rolled or cold-rolled, uncoated mild steel, of conventional welding quality and up to 3 mm thick, as single projections, in multiples or as a group of multiples.
Buckel zum Widerstandsschweißen (ISO 8167:1989)
Bossages pour le soudage par résistance (ISO 8167:1989)
La présente Norme internationale prescrit les caractéristiques et fixe les dimensions des bossages utilisés pour le soudage par résistance. Elle indique également la forme et les dimensions recommandées des outils (voir annexe B). Les bossages peuvent être formés sur des tôles en acier doux, laminées à chaud ou à froid, normalement aptes au soudage et d'épaisseur ne dépassant pas 3 mm, isolément, par groupes ou ensemble de groupes.
Bradavice za elektrouporovno varjenje (ISO 8167:1989)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bradavice za elektrouporovno varjenje (ISO 8167:1989)Buckel zum Widerstandsschweißen (ISO 8167:1989)Bossages pour le soudage par résistance (ISO 8167:1989)Projections for resistance welding (8167:1989)25.160.30Varilna opremaWelding equipmentICS:Ta slovenski standard je istoveten z:EN 28167:1992SIST EN 28167:1999en01-december-1999SIST EN 28167:1999SLOVENSKI
STANDARD
IS08167 :1989 (E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern- mental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the IS0 Council. They are approved in accordance with IS0 procedures requiring at least 75 % approval by the member bodies voting. International Standard IS0 8167 was prepared by Technical Committee ISO/TC 44, Welding and allied processes. Annexes A and B of this International Standard are for information only. 0 IS0 1989 All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale 56 l CH-121 1 Geneve 20 l Switzerland Printed in Switzerland SIST EN 28167:1999
INTERNATIONAL STANDARD IS0 8167 : 1989 (E) Projections for resistance welding 1 Scope 60 0 This International Standard specifies the characteristics and dimensions of projections for resistance welding; it also includes the appropriate design and dimensions for tools (see annex B). The projections may be used on either hot-rolled or cold-rolled, uncoated mild steel, of conventional welding quaiity and up to 3 mm thick, as single projections, in multiples or as a group of multiples. 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encourag- ed to investigate the possibility of applying the most recent edi- tion of the standard indicated below. Members of IEC and IS0 maintain registers of currently valid International Sta
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.