EN 914:2020

Gymnastic equipment - Parallel bars and combination asymmetric/parallel bars - Requirements and test methods including safety

This document specifies functional requirements (see Clause 4) and specific safety requirements in addition to the general safety requirements in EN 913 (see Clause 5), which is read in conjunction with this standard.
This document is applicable to three types of parallel bars (see Table 1) intended for use under supervision of a competent person.

Turngeräte - Barren und kombinierte Stufenbarren/Barren - Anforderungen und Prüfverfahren einschließlich Sicherheit

Dieses Dokument legt funktionelle Anforderungen (siehe Abschnitt 4) und besondere sicherheitstechnische Anforderungen zusätzlich zu den allgemeinen Sicherheitsanforderungen nach EN 913 (siehe Abschnitt 5) fest, welche im Zusammenhang mit dieser Norm gelesen wird.
Dieses Dokument gilt für drei Typen von Barren (siehe Tabelle 1), die zur Nutzung unter Aufsicht einer fachkundigen Person bestimmt sind.

Matériel de gymnastique - Barres parallèles et barres parallèles/asymétriques combinées - Exigences et méthodes d’essai y compris de sécurité

Le présent document spécifie des exigences fonctionnelles (voir Article 4) et des exigences spécifiques de sécurité qui s’ajoutent aux exigences générales de sécurité spécifiées dans l’EN 913 (voir Article 5), qui est lue conjointement avec cette norme.
Le présent document s’applique à trois types de barres parallèles (voir Tableau 1) destinés à être utilisés sous la surveillance d’une personne compétente.

Gimnastična oprema - Bradlja in dvovišinska bradlja - Zahteve in preskusne metode, vključno z varnostjo

General Information

• Status: Published
• Publication Date: 19-May-2020
• Withdrawal Date: 29-Nov-2020
• ICS: 97.220.30 - Indoor sports equipment
• Technical Committee: CEN/TC 136 - Sports, playground and other recreational equipment
• Drafting Committee: CEN/TC 136/WG 22 - Gymnastic and playing field equipment
• Directive: 2001/95/EC - Directive 2001/95/EC of the European Parliament and of the Council of 3 December 2001 on general product safety
• Mandate: M/507 - Standardisation mandate issued to the European standardisation organisations (ESOs) to develop European standards for gymnastic equipment
• Ref Project: SIST EN 914:2020 - Gymnastic equipment - Parallel bars and combination asymmetric/parallel bars - Requirements and test methods including safety

Relations

• Replaces: EN 914:2008 - Gymnastic equipment - Parallel bars and combination asymmetric/parallel bars - Requirements and test methods including safety
• Effective Date: 27-May-2020

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 914:2020
01-julij-2020
Nadomešča:
SIST EN 914:2009
Gimnastična oprema - Bradlja in dvovišinska bradlja - Zahteve in preskusne
metode, vključno z varnostjo
Gymnastic equipment - Parallel bars and combination asymmetric/parallel bars -
Requirements and test methods including safety
Turngeräte - Barren und kombinierte Stufenbarren/Barren - Anforderungen und
Prüfverfahren einschließlich Sicherheit
Matériel de gymnastique - Barres parallèles et barres parallèles/asymétriques
combinées - Exigences et méthodes d'essai y compris la sécurité
Ta slovenski standard je istoveten z: EN 914:2020
ICS:
97.220.30 Oprema za dvoranske športe Indoor sports equipment
SIST EN 914:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 914:2020

---------------------- Page: 2 ----------------------
SIST EN 914:2020


EN 914
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2020
EUROPÄISCHE NORM
ICS 97.220.30 Supersedes EN 914:2008
English Version

Gymnastic equipment - Parallel bars and combination
asymmetric/parallel bars - Requirements and test
methods including safety
Matériel de gymnastique - Barres parallèles et barres Turngeräte - Barren und kombinierte
parallèles/asymétriques combinées - Exigences et Stufenbarren/Barren - Anforderungen und
méthodes d'essai y compris de sécurité Prüfverfahren einschließlich Sicherheit
This European Standard was approved by CEN on 20 April 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 914:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 914:2020
EN 914:2020 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Requirements . 5
4.1 Classification . 5
4.2 Dimensions . 6
4.3 Protection against damaging the floor . 7
4.4 Gap between the longitudinal/cross member . 7
4.5 Transport equipment . 8
5 Safety requirements . 8
5.1 General requirements .
...