FprEN 12166

Copper and copper alloys - Wire for general purposes

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy wire, finally produced by drawing, rolling or extruding, intended for general purposes, spring and fastener manufacturing applications.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

Kupfer und Kupferlegierungen - Drähte zur allgemeinen Verwendung

Dieses Dokument legt die Zusammensetzung, die Anforderungen an die Eigenschaften und die Grenzabmaße für durch Ziehen, Walzen oder Pressen endgefertigte Drähte aus Kupferlegierungen zur allgemeinen Verwen
dung und zur Herstellung von Federn und Verbindungselementen fest.
Der Ablauf der Probenahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforde
rungen dieses Dokuments sind ebenfalls festgelegt

Cuivre et alliages de cuivre - Fils pour usages généraux

Le présent document spécifie la composition, les exigences de propriétés et les tolérances dimensionnelles des fils en alliage de cuivre, fabriqués par étirage, laminage ou filage, destinés à des usages généraux, des applications de fabrication de ressorts et de fixations.
Les modes opératoires d’échantillonnage et les méthodes d’essai pour la vérification de la conformité aux exigences du présent document sont également spécifiés.

Baker in bakrove zlitine - Žica za splošno uporabo

General Information

• Status: Not Published
• Publication Date: 28-Aug-2024
• ICS: 77.150.30 - Copper products
• Technical Committee: CEN/TC 133 - Copper and copper alloys
• Drafting Committee: CEN/TC 133/WG 4 - Extruded and drawn products, forgings and scrap
• Current Stage: 4599 - Dispatch of FV draft to CMC - Finalization for Vote
• Start Date: 19-Sep-2023
• Due Date: 19-Jun-2023
• Completion Date: 19-Sep-2023
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: oSIST prEN 12166:2022 - Copper and copper alloys - Wire for general purposes

Relations

• Revises: EN 12166:2016 - Copper and copper alloys - Wire for general purposes
• Effective Date: 09-Oct-2019

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 12166:2022
01-oktober-2022
Baker in bakrove zlitine - Žica za splošno uporabo
Copper and copper alloys - Wire for general purposes
Kupfer und Kupferlegierungen - Drähte zur allgemeinen Verwendung
Cuivre et alliages de cuivre - Fils pour usages généraux
Ta slovenski standard je istoveten z: prEN 12166
ICS:
77.150.30 Bakreni izdelki Copper products
oSIST prEN 12166:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 12166:2022

---------------------- Page: 2 ----------------------
oSIST prEN 12166:2022


DRAFT
EUROPEAN STANDARD
prEN 12166
NORME EUROPÉENNE

EUROPÄISCHE NORM

August 2022
ICS 77.150.30 Will supersede EN 12166:2016
English Version

Copper and copper alloys - Wire for general purposes
Cuivre et alliages de cuivre - Fils pour usages généraux Kupfer und Kupferlegierungen - Drähte zur
allgemeinen Verwendung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 133.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12166:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 12166:2022
prEN 12166:2022 (E)
Contents Page

European foreword . 4
Introduction . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Designation. 8
4.1 Material . 8
4.1.1 General . 8
4.1.2 Symbol . 8
4.1.3 Number . 8
4.2 Material condition . 8
4.3 Product . 8
5 Ordering information .
...