EN 12166:2016
(Main)Copper and copper alloys - Wire for general purposes
Copper and copper alloys - Wire for general purposes
This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy wire, finally produced by drawing, rolling or extruding, intended for general purposes, spring and fastener manufacturing applications.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.
Kupfer und Kupferlegierungen - Drähte zur allgemeinen Verwendung
Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften und die Grenz¬abmaße für durch Ziehen, Walzen oder Pressen endgefertigte Drähte aus Kupferlegierungen zur allgemeinen Verwendung und zur Herstellung von Federn und Verbindungselementen fest.
Der Ablauf der Probenahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieser Europäischen Norm sind ebenfalls festgelegt.
Cuivre et alliages de cuivre - Fils pour usages généraux
La présente Norme européenne spécifie la composition, les exigences de propriétés et les tolérances dimensionnelles des fils en alliage de cuivre, fabriqués par étirage, laminage ou filage, destinés à des usages généraux, des applications de fabrication de ressorts et de fixations.
Les modes opératoires d'échantillonnage et les méthodes d'essai pour la vérification de la conformité aux exigences de la présente Norme européenne sont également spécifiés.
Baker in bakrove zlitine - Žica za splošno uporabo
Ta evropski standard določa sestavo, zahteve glede značilnosti in odstopanja glede mer za žice iz bakrovih zlitin, končno izdelane z vlečenjem, valjanjem ali ekstrudiranjem, namenjene za splošno uporabo, izdelavo vzmeti in veznih sredstev.
Določeni so tudi postopki vzorčenja in preskusne metode za preverjanje skladnosti z zahtevami tega evropskega standarda.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Žica za splošno uporaboKupfer und Kupferlegierungen - Drähte zur allgemeinen VerwendungCuivre et alliages de cuivre - Fils pour usages générauxCopper and copper alloys - Wire for general purposes77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 12166:2016SIST EN 12166:2016en,fr,de01-oktober-2016SIST EN 12166:2016SLOVENSKI
STANDARDSIST EN 12166:20111DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12166
July
t r s x ICS
y yä s w rä u r Supersedes EN
s t s x xã t r s sEnglish Version
Copper and copper alloys æ Wire for general purposes Cuivre et alliages de cuivre æ Fils pour usages généraux Kupfer und Kupferlegierungen æ Drähte zur allgemeinen Verwendung This European Standard was approved by CEN on
{ April
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s t s x xã t r s x ESIST EN 12166:2016
Position of wire cross-section within a coil, reel, spool or drum . 40 Bibliography . 42 SIST EN 12166:2016
Figures Figure 1 — Calculation of corner radii . 14 Figure A.1 — Illustration of position of wire cross-section within the coil (bunched wound or stagger/traverse wound) . 40 Figure A.2 — Illustration of position of wire cross-section within the reel/spool/drum (stagger/traverse wound) . 40 Figure A.3 — Illustration of position of wire cross-section within the coil (bunched wound or stagger/traverse wound) . 41 Figure A.4 — Illustration of position of wire cross-section within the reel/spool/drum (stagger/traverse wound) . 41
Tables Table 1 — Composition of low alloyed copper alloys . 18 Table 2 — Composition of copper-nickel-zinc alloys . 21 Table 3 — Composition of copper-tin alloys . 21 Table 4 — Composition of copper-zinc alloys . 22 Table 5 — Composition of copper-zinc-lead alloys . 23 Table 6 — Composition of complex copper-zinc alloys. 24 Table 7 — Mechanical properties of wire of low alloyed copper alloys. 24 Table 8 — Mechanical properties of wire of copper-nickel-zinc alloys . 27 Table 9 — Mechanical properties of wire of copper-tin alloys . 29 Table 10 — Mechanical properties of wire of copper-zinc alloys . 31 Table 11 — Mechanical properties of wire of copper-zinc-lead alloys . 35 Table 12 — Mechanical properties of wire of complex copper-zinc alloys . 36 Table 13 — Grain size designations . 37 Table 14 — Tolerances on diameter of round wire . 37 Table 15 — Tolerances on width across-flats of square or regular polygonal wire . 38 Table 16 — Tolerances on width and thickness of rectangular wire . 38 Table 17 — Corner radii for square or rectangular wire . 39 Table 18 — Sampling rate . 39
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.