EN 62282-2:2004
(Main)Fuel cell technologies - Part 2: Fuel cell modules
Fuel cell technologies - Part 2: Fuel cell modules
Provides the minimum requirements for safety and performance of fuel cell modules. Applies to fuel cell modules with the following electrolyte chemistry: alkaline; proton exchange membrane (including direct methanol fuel cells); phosphoric acid; molten carbonate; solid oxide fuel cell modules.
Brennstoffzellentechnologien - Teil 2: Brennstoffzellen-Module
Technologies des piles à combustible - Partie 2: Modules à piles à combustible
Donne les exigences minimales de sécurité et de performance des modules à piles à combustible. S'applique aux modules à piles à combustible avec les différents types d'électrolytes suivants: alcalins; à membrane échangeuse de protons (y compris piles à combustible à méthanol direct); à acide phosphorique; à carbonates fondus; à oxyde solide.
Tehnologije gorivnih celic – 2. del: Moduli gorivnih celic
General Information
Relations
Standards Content (Sample)
STANDARDTehnologije gorivnih celic – 2. del: Moduli gorivnih celicFuel cell technologies – Part 2: Fuel cell modules©
Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljenoReferenčna številkaSIST EN 62282-2:2005(en)ICS27.070
EUROPEAN STANDARD
EN 62282-2 NORME EUROPÉENNE EUROPÄISCHE NORM
November 2004 CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62282-2:2004 E
ICS 27.070
English version
Fuel cell technologies Part 2: Fuel cell modules (IEC 62282-2:2004)
Technologies des piles à combustible Partie 2: Modules à piles à combustible (CEI 62282-2:2004)
Brennstoffzellentechnologien Teil 2: Brennstoffzellen-Module (IEC 62282-2:2004)
This European Standard was approved by CENELEC on 2004-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
at national level by publication of an identical
national standard or by endorsement
(dop)
2005-07-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2007-10-01 Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 62282-2:2004 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60664-1 NOTE Harmonized as EN 60664-1:2003 (not modified). IEC 60112 NOTE Harmonized as EN 60112:2003 (not modified). IEC 60730 NOTE Harmonized in EN 60730 series (not modified). ISO 228-1 NOTE Harmonized as EN ISO 228-1:2003 (not modified). ISO 228-2 NOTE Harmonized as EN ISO 228-2:2003 (not modified). __________
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60079 Series Electrical apparatus for explosive gas atmospheres
EN 50014 &
related ENs EN 60079
Series
Series IEC 60079-10 - 1) Part 10: Classification of hazardous areas EN 60079-10 2003 2) IEC 60352 Series Solderless connections
EN 60352 Series IEC 60512-8 - 1) Electromechanical components for electronic equipment; basic testing procedures and measuring methods Part 8: Connector tests (mechanical) and mechanical tests on contacts and terminations
- - IEC 60529 - 1) Degrees of protection provided by enclosures (IP Code)
EN 60529 + corr. May 1991 2)1993 IEC 60617
database Graphical symbols for diagrams
- - IEC 60695 Series Fire hazard testing
EN 60695 Series IEC 60812 - 1) Analysis techniques for system reliability -Procedure for failure mode and effects analysis (FMEA)
HD 485 S1 1987 2) IEC 61025 - 1) Fault tree analysis (FTA)
HD 617 S1 1992 2) IEC 61508 Series Functional safety of electrical/electronic/programmable electronic safety-related systems
EN 61508 Series IEC 61508-1 - 1) Functional safety of electrical/electronic/programmable electronic safety-related systems Part 1: General requirements EN 61508-1 2001 2)
1) Undated reference.
2) Valid edition at date of issue.
- - ISO 188 1998 Rubber, vulcanized or thermoplastic - Accelerated ageing and heat-resistance tests
- - ISO 1307 1992 Rubber and plastics hoses for general-purpose industrial applications - Bore diameters and tolerances, and tolerances on length
EN ISO 1307 1995 ISO 1402 1994 Rubber and plastics hoses and hose assemblies - Hydrostatic testing
EN ISO 1402 1996 ISO 1436-1 2001 Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types - Specification Part 1: Oil-based fluid applications
- - ISO 4672 1997 Rubber and plastics hoses - Sub-ambient temperature flexibility tests
EN ISO 4672 1999
Electronic equipment for use in power installations
EN 50178 1997
NORMEINTERNATIONALECEIIECINTERNATIONALSTANDARD62282-2Première éditionFirst edition2004-07Technologies des piles à combustible – Partie 2: Modules à piles à combustible Fuel cell technologies – Part 2: Fuel cell modules Pour prix, voir catalogue en vigueur For price, see current catalogue” IEC 2004
Droits de reproduction réservés
Copyright - all rights reservedAucune partie de cette publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l'éditeur. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission,
3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch
Web: www.iec.ch CODE PRIX PRICE CODE WCommission Electrotechnique InternationaleInternational Electrotechnical Commission
62282-2 ” IEC:2004 – 3 – CONTENTSFOREWORD.5INTRODUCTION.91 Scope.11 2 Normative references.13 3 Terms and definitions.15 4 Requirements.234.1 General safety strategy.23 4.2 Design requirements.25 5 Type tests.35 5.1 Gas leakage test.35 5.2 Normal operation.37 5.3 Allowable working pressure test.39 5.4 Pressure withstanding test of cooling system.41 5.5 Electrical overload test.41 5.6 Overpressure test.41 5.7 Dielectric strength test.41 5.8 Differential pressure test.45 5.9 Gas leakage test (repeat).45 5.10 Normal operation (repeat).45 5.11 Flammable concentration test.45 5.12 Tests of abnormal conditions.47 6 Routine tests.516.1 Gas-tightness test.51 6.2 Dielectric strength withstand test.51 7 Markings and instructions.51 7.1 Nameplate.51 7.2 Marking.53 7.3 Warning label.53 7.4 Documentation.53 Annex A (informative) Additional information for the performance and evaluation
of the tests.61 Bibliography.75 Figure 1 – Fuel cell system components and scope of standard.13 Table 1
Dielectric strength test voltages (derived from EN 50178).43 Table A.1 – Viscosity of gases at one atmosphere.67
62282-2 ” IEC:2004 – 5 – INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________FUEL CELL TECHNOLOGIES –
Part 2: Fuel cell modules FOREWORD1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62282-2 has been prepared by IEC technical committee 105: Fuel cell technologies. The text of this standard is based on the following documents: FDIS Report on voting 105/73/FDIS 105/77/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
62282-2 ” IEC:2004 – 7 – IEC 62282 consists of the following parts under the general title Fuel cell technologies:Part 1:
Terminology1Part 2: Fuel cell modules Pa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.