EN 50607:2015
(Main)Satellite signal distribution over a single coaxial cable - Second generation
Satellite signal distribution over a single coaxial cable - Second generation
This standard describes: the system physical structure; the system control signals, which implement a set of messages using DiSEqC physical layer but not the DiSEqC message structure; the definition of identified configurations; the management of the potential collisions in the control signals traffic. Figure 1 illustrates the physical system configuration considered in this standard. Several satellite signal demodulators can receive signals from any of the input signal banks (Bank 1, Bank 2, Bank M, with M 256) of the LNB or the switch. The signals selected by the demodulators (or receivers) are transported via a single cable to these demodulators (Receiver 1, Receiver 2, Receiver N, with N 32). To achieve these single cable distributions, the Single Cable Interface (SCIF, likely embedded in a LNB or a Switch) features some specific functions and characteristics.
Verteilen von Satellitensignalen über ein Koaxialkabel ‒ Zweite Generation
Distribution de signaux par satellite sur un seul câble coaxial - Deuxième génération
La présente Norme européenne décrit: ▪ la structure physique du système; ▪ les signaux de commande du système, qui mettent en oeuvre un ensemble de messages qui utilisent la couche physique DiSEqC, mais pas la structure de message DiSEqC; ▪ la définition des configurations identifiées; ▪ la gestion des collisions potentielles dans le trafic des signaux de commande. La Figure 1 représente la configuration physique de système prise en considération dans la présente norme. Plusieurs démodulateurs de signaux satellites peuvent recevoir des signaux issus de batteries de signaux d'entrée (Batterie 1, Batterie 2, Batterie M, avec M ≤ 256) du LNB ou du commutateur. Les signaux sélectionnés par les démodulateurs (ou récepteurs) sont transportés par un seul câble vers ces démodulateurs (Récepteur 1, Récepteur 2, Récepteur N, avec N ≤ 32). Pour réaliser ces distributions par un seul câble, l'interface à un seul câble (SCIF, vraisemblablement incorporée dans un LNB ou un commutateur) présente un certain nombre de fonctions et caractéristiques spécifiques.
Distribucija satelitskih signalov po enojnem koaksialnem kablu - Druga generacija
V tem evropskem standardu je opisano naslednje:
▪ fizična struktura sistema;
▪ kontrolni signali sistema, ki uvajajo nabor sporočil na podlagi fizične plasti DiSEqC in ne strukture sporočil DiSEqC;
▪ definicija prepoznanih konfiguracij;
▪ upravljanje morebitnih trčenj v prometu s kontrolnimi signali.
Slika 1 prikazuje konfiguracijo fizičnega sistema, ki jo obravnava ta standard.
Več demodulatorjev satelitskega signala lahko sprejema signale iz katerega koli vhodnega niza signalov (Niz 1, Niz 2, Niz M, pri čemer je M ≤ 256) LNB ali stikala. Signali, ki jih izberejo demodulatorji (ali sprejemniki), se prenesejo v te demodulatorje (Sprejemnik 1, Sprejemnik 2, Sprejemnik N, pri čemer je N ≤ 32) po enojnem kablu.
Za doseganje take distribucije po enojnem kablu ima vmesnik SCIF (Single Cable Interface, ki je verjetno vdelan v LNB ali stikalo) nekatere posebne funkcije in karakteristike.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2015
1DGRPHãþD
SIST-TS CLC/TS 50607:2013
Distribucija satelitskih signalov po enojnem koaksialnem kablu - Druga generacija
Satellite signal distribution over a single coaxial cable - Second generation
Verteilen von Satellitensignalen über ein Koaxialkabel - Zweite Generation
Distribution de signaux par satellite sur un seul câble coaxial - Deuxième génération
Ta slovenski standard je istoveten z: EN 50607:2015
ICS:
33.060.40 Kabelski razdelilni sistemi Cabled distribution systems
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 50607
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2015
ICS 33.060.40 Supersedes CLC/TS 50607:2013
English Version
Satellite signal distribution over a single coaxial cable - Second
generation
Distribution de signaux par satellite sur un seul câble Verteilen von Satellitensignalen über ein Koaxialkabel ¿
coaxial - Deuxième génération Zweite Generation
This European Standard was approved by CENELEC on 2014-10-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50607:2015 E
Contents Page
Foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Abbreviations . 8
3.3 Used commands . 8
4 System architecture . 9
5 SCIF control signals. 12
5.1 DC levels . 12
5.2 Method of the data bit signalling . 14
6 Structure and format of the messages of the 2nd generation single cable distribution system (SCD2)14
6.1 Backwards Compatibility to EN 50494 . 14
6.2 Non-DiSEqC structure . 14
6.3 Uni-directional operation . 15
6.4 Bi-directional operation . 15
7 SCD2 commands . 15
7.1 ODU_Channel_change . 15
7.1.1 Formats . 15
7.1.2 “Special” frequencies . 16
7.2 ODU_Channel_change_PIN . 16
7.3 ODU_UB_avail . 17
7.4 ODU_UB_PIN . 18
7.5 ODU_UB_inuse . 18
7.6 ODU_UB_freq . 19
7.7 ODU_UB_switches . 20
8 Conventions . 21
8.1 UB slots numbering . 21
8.2 Numbering of satellite IF banks . 22
9 Traffic collision management rules . 22
9.1 General . 22
9.2 Automatic detection of SCIF control signal failure . 22
9.3 Pseudo-random repeat . 23
9.3.1 Handling of SCIF control signal . 23
9.3.2 Random delay generation law . 23
Annex A (normative) Implementation rules . 25
A.1 User interface . 25
A.2 Installation impedance . 25
A.3 Signal reflection and return loss in installations . 26
A.4 Power supply of the SCIF . 26
A.5 Remarks concerning power supply . 27
Bibliography . 28
‒ 3 ‒ EN 50607:2015
Foreword
This document (EN 50607:2015) has been prepared by CLC/TC 209 “Cable networks for television signals,
sound signals and interactive services”.
The following dates are fixed:
• latest date by which this document has (dop) 2015-10-20
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2017-10-20
standards conflicting with this
document have to be withdrawn
This document supersedes CLC/TS 50607:2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Introduction
In EN 61319-1:1996, the interfaces for the control and command of the devices associated with the satellite
receivers are described in the following clauses:
▪ Clause 4: Interfaces requirements for polarizer and polar switchers;
▪ Clause 5: Interfaces requirements for low-noise block converters (LNB).
In these clauses, analogue techniques are described for controlling the LNB and polar switchers.
TM
In the DiSEqC Bus Functional Specification, the “Digital Satellite Equipment Control Bus” (called DiSEqC)
is introduced as a single method of communication between the satellite and the peripheral equipment, using
only the existing coaxial cables. The existing EN 50494 “Satellite signal distribution over a single coaxial
cable in single dwelling installations” describes a system for distributing signals via single coaxial cable
issued from different bands and polarisations to several satellite receivers This specification is limited to 8
units per output of the Single Cable Interface and to 8 Satellite IF banks (bands, feeds, polarisations).
The second generation described in this standard is intended for single and multiple dwelling installations
and includes the following enhancements compared to EN 50494:
▪ The number of demodulators is extended to a maximum of 32 units per output of the Single Cable
Interface (hereafter referred to as SCIF) device.
▪ The system is scaled for a maximum number of 256 Satellite IF banks (bands, feeds, polarisations)
▪ The SCIF replies, which may be used during installation process, are also based on DiSEqC.
▪ Equipment according to this standard is downwards compatible to the specifications provided by
EN 50494.
‒ 5 ‒ EN 50607:2015
1 Scope
This European Standard describes:
▪ the system physical structure;
▪ the system control signals, which implement a set of messages using DiSEqC physical layer but not the
DiSEqC message structure;
▪ the definition of identified configurations;
▪ the management of the potential collisions in the control signals traffic.
Figure 1 illustrates the physical system configuration considered in this standard.
Several satellite signal demodulators can receive signals from any of the input signal banks (Bank 1, Bank 2,
Bank M, with M ≤ 256) of the LNB or the switch. The signals selected by the demodulators (or receivers) are
transported via a single cable to these demodulators (Receiver 1, Receiver 2, Receiver N, with N ≤ 32).
To achieve these single cable distributions, the Single Cable Interface (SCIF, likely embedded in a LNB or a
Switch) features some specific functions and characteristics.
Figure 1 — General architecture of the single cable distribution
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 50494, Satellite signal distribution over a single coaxial cable in single dwelling installations
EN 60728-1, Cable networks for television signals, sound signals and interactive services – Part 1: System
performance of forward paths (IEC 60728-1)
EN 60728-4, Cable networks for television signals, sound signals and interactive services – Part 4: Passive
wideband equipment for coaxial cable networks (IEC 60728-4)
EN 61319-1:1996, Interconnections of satellite receiving equipment – Part 1: Europe (IEC 61319-1:1995)
IEC 60050-371, International Electrotechnical Vocabulary - Chapter 371: Telecontrol
IEC 60050-721, International Electrotechnical Vocabulary - Chapter 721: Telegraphy, facsimile and data
communication
TM 1
DiSEqC Bus Functional Specification, Version 4.2, February 25, 1998
3 Terms, definitions and abbreviations
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60050-371, IEC 60050-721,
EN 60728-1 and the following ones apply.
3.1.1
bank
group of contiguous channels belonging to a polarisation and/or a band
3.1.2
channel
radio frequency transponder signal
3.1.3
command
information used to cause a change of state of operational equipment; could be part of message
[SOURCE: IEC 60050-371:1984, 371-03-01, modified]
3.1.4
committed switch
switch with specified functio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.