iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61290-2-3:1998

(Main)

Optical fibre amplifiers - Basic specification - Part 2-3: Test methods for optical power parameters - Optical power meter

Optical fibre amplifiers - Basic specification - Part 2-3: Test methods for optical power parameters - Optical power meter

Applies to optical fibre amplifiers using active fibres, containing rare-earth dopants, presently commercially available. Establishes uniform requirements for accurate and reliable measurements, by means of optical power meter test method, of the following OFA parameters: - nominal output signal power; - large-signal output stability; - saturation output power; - maximum input signal power; - maximum output signal power; - input power range; - output power range; - maximum total output power.

Lichtwellenleiter-Verstärker - Grundspezifikation - Teil 2-3: Prüfverfahren für optische Leistungsparameter - Optischer Leistungsmesser

Amplificateurs à fibres optiques - Spécification de base - Partie 2-3: Méthodes d'essai pour les paramètres de puissance optique - Mesureur de puissance optique

S'applique aux amplificateurs à fibres optiques (AFO) utilisant des fibres actives contenant des dopants de terre rare, actuellement commercialisés. Etablit des spécifications uniformes pour des mesures précises et fiables, par le biais de la méthode d'essai du mesureur de puissance optique, des paramètres d'AFO donnés ci-dessous: - puissance nominale du signal de sortie; - stabilité de sortie pour les grands signaux; - puissance de saturation en sortie; - puissance maximale du signal d'entrée; - puissance maximale du signal de sortie; - intervalle de puissance d'entrée; - intervalle de puissance de sortie; - puissance totale maximale de sortie.

Optical fibre amplifiers - Basic specification - Part 2-3: Test methods for optical power parameters - Optical power meter (IEC 61290-2-3:1998)

General Information

Status
Withdrawn
Publication Date
10-Aug-1998
Withdrawal Date
31-Jan-2006
ICS
33.180.01 - Fibre optic systems in general
Technical Committee
CLC/SR 86C - Fibre optic systems and active devices
Drafting Committee
IEC/SC 86C - IEC_SC_86C
Parallel Committee
IEC/SC 86C - IEC_SC_86C
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Feb-2006
Completion Date
01-Feb-2006
Ref Project
SIST EN 61290-2-3:1999 - Optical fibre amplifiers - Basic specification -- Part 2-3: Test methods for optical power parameters - Optical power meter

Relations

Replaced By
EN 61290-1-3:2005 - Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method
Effective Date
29-Jan-2023

Buy Standard

EN 61290-2-3:1999EN 61290-2-3:1999
PreviousNext
Standard
EN 61290-2-3:1999
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61290-2-3:1999
01-maj-1999
Optical fibre amplifiers - Basic specification - Part 2-3: Test methods for optical
power parameters - Optical power meter (IEC 61290-2-3:1998)
Optical fibre amplifiers - Basic specification -- Part 2-3: Test methods for optical power
parameters - Optical power meter
Lichtwellenleiter-Verstärker - Grundspezifikation -- Teil 2-3: Prüfverfahren für optische
Leistungsparameter - Optischer Leistungsmesser
Amplificateurs à fibres optiques - Spécification de base -- Partie 2-3: Méthodes d'essai
pour les paramètres de puissance optique - Mesureur de puissance optique
Ta slovenski standard je istoveten z: EN 61290-2-3:1998
ICS:
33.180.30 2SWLþQLRMDþHYDOQLNL Optic amplifiers
SIST EN 61290-2-3:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61290-2-3:1999

---------------------- Page: 2 ----------------------

SIST EN 61290-2-3:1999

---------------------- Page: 3 ----------------------

SIST EN 61290-2-3:1999

---------------------- Page: 4 ----------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 61280-1-4:2023(Main)
Fibre optic communication subsystem test procedures - Part 1-4: General communication subsystems - Light source encircled flux measurement method
SIST EN IEC 61280-1-4:2023

IEC 61280-1-4:2023 is available as IEC 61280-1-4:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61280-1-4:2023 establishes the characterization process of the encircled flux measurement method of light sources intended to be used with multimode fibre. This document sets forth a procedure for the collection of two-dimensional fibre optic nearfield greyscale data and subsequent reduction to one-dimensional data expressed as a set of three sampled parametric functions of radius from the fibre’s optical centre. Estimation of the fibre core diameter is not an objective of this document. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - improvement of calibration procedure and calibration traceability; - improvement of fibre shaker description and requirements; - addition of pulsed light sources; - removal of a poorly traceable calibration process using a micro positioner.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62343:2023(Main)
Dynamic modules - Generic specification
SIST EN IEC 62343:2023

IEC 62343:2023 is available as IEC 62343:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62343:2023 applies to all commercially available optical dynamic modules and devices. It describes the products covered by the IEC 62343 series, defines terminology, fundamental considerations and basic approaches. The object of this document is to: - establish uniform requirements for operation, reliability and environmental properties of dynamic modules (DMs) to be implemented in the appropriate DM standard, and - provide assistance to the purchaser in the selection of consistently high-quality DM products for their particular applications, as well as in the consultation of the appropriate specific DM standard(s). This document covers performance templates, performance standards, reliability qualification requirements, hardware and software interfaces and related testing methods. Since a dynamic module integrates an optical module/device, printed wiring board, and software/firmware, the standards developed in the series will mimic appropriate existing standards. On the other hand, since "dynamic module" is a relatively new product category, the dynamic module standards series will not be bound by the existing practices where requirements differ.The safety standards as related to dynamic modules are mostly optical power considerations, which is covered by the IEC 60825 series (see Clause 6). This third edition cancels and replaces the second edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - addition of terms and definitions for optical multicast switches (3.8); - revision of Clause 4, listing the requirements for standards in the IEC 62343 series; - addition of Clause 6 (Safety requirements).

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61280-4-1:2019/AC:2022-12(Corrigendum)
Fibre-optic communication subsystem test procedures - Part 4-1: Installed cabling plant - Multimode attenuation measurement
SIST EN IEC 61280-4-1:2019/AC:2023

IEC Corrected version

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62007-1:2015/A1:2022(Amendment)
Semiconductor optoelectronic devices for fibre optic system applications - Part 1: Specification template for essential ratings and characteristics
SIST EN 62007-1:2015/A1:2023
  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61280-4-3:2022(Main)
Fibre optic communication subsystem test procedures - Part 4-3: Installed passive optical networks - Attenuation and optical return loss measurements
SIST EN IEC 61280-4-3:2022

IEC 61280-4-3: 2022 describes the measurement of attenuation, optical return loss and optical power in installed passive optical networks (PONs) using single-mode fibre. This document specifies two methods for measuring the attenuation before activation of the PON:  method A: one-cord method using a light source and a power meter (LSPM); method B: optical time-domain reflectometer (OTDR) method in upstream direction only, with reduction of uncertainties due to the variation of backscatter coefficient.  In addition, method C, which is described in informative Annex C, provides an estimate of the attenuation after partial activation of the PON by using a U band filtered optical time-domain reflectometer (FOTDR) in an upstream direction. This publication contains an attached file titled "Supplemental Data" in the form of an Excel spread sheet. This file is intended to be used as a complement and does not form an integral part of the standard.

  • Standard
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61280-4-1:2019/A1:2022(Amendment)
Fibre-optic communication subsystem test procedures - Part 4-1: Installed cabling plant - Multimode attenuation measurement
SIST EN IEC 61280-4-1:2019/A1:2022
  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61280-4-5:2020/AC:2022-02(Corrigendum)
Fibre-optic communication subsystem test procedures - Part 4-5: Installed cabling plant - Attenuation measurement of MPO terminated fibre optic cabling plant using test equipment with MPO interfaces
SIST EN IEC 61280-4-5:2020/AC:2022

IEC Corrected version

  • Corrigendum
    4 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61280-1-3:2021(Main)
Fibre optic communication subsystem test procedures - Part 1-3: General communication subsystems - Measurement of central wavelength, spectral width and additional spectral characteristics
SIST EN IEC 61280-1-3:2021

This part of IEC 61280 provides definitions and measurement procedures for several wavelength and spectral width properties of an optical spectrum associated with a fibre optic communication subsystem, an optical transmitter, or other light sources used in the operation or test of communication subsystems. This document also provides definitions and measurement procedures for side mode suppression ratio and signal to source spontaneous emission ratio. The measurement is done for the purpose of system construction and/or maintenance. In the case of communication subsystem signals, the optical transmitter is typically under modulation. NOTE Different properties may be appropriate to different spectral types, such as continuous spectra characteristic of light-emitting diodes (LEDs), and multilongitudinal-mode (MLM), multitransverse-mode (MTM) and single-longitudinal mode (SLM) spectra, characteristic of laser diodes (LDs).

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61280-4-5:2020(Main)
Fibre-optic communication subsystem test procedures - Part 4-5: Installed cabling plant - Attenuation measurement of MPO terminated fibre optic cabling plant using test equipment with MPO interfaces
SIST EN IEC 61280-4-5:2020

IEC 61280-4-5: 2020 is applicable to the measurement of attenuation and determination of polarity and length of installed multimode and single-mode optical fibre cabling plant, terminated with MPO connectors, using test equipment having an MPO interface. This cabling plant can include multimode or single-mode optical fibres, connectors, adapters, splices, and other passive devices. The cabling can be installed in a variety of environments including residential, commercial, industrial, and data centre premises, as well as outside plant environments. In this document, the optical fibres that are addressed include sub-categories A1-OMx, where x = 2, 3, 4 and 5 (50/125 μm) multimode optical fibres, as specified in IEC 60793-2-10, and category B-652 and B-657 (9/125 μm) single-mode optical fibres, as specified in IEC 60793-2-50. The attenuation measurements of the other multimode and single-mode categories can also be made using a light source and power meter (LSPM) or optical time domain reflectometer (OTDR) utilising an internal or external optical switch having one MPO interface. Multimode measurements are made with an 850 nm source because transceivers used for parallel optics applications having an MPO interface only operate at 850 nm; 1 300 nm measurements are optional. Single-mode measurements are made with a 1 310 nm and/or 1 550 nm source because transceivers used for parallel optics applications having an MPO interface operate at these wavelengths. This document does not include descriptions of cabling that is not exclusively MPO to MPO.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62614-1:2020(Main)
Fibre optics - Multimode launch conditions - Part 1: Launch condition requirements for measuring multimode attenuation
SIST EN IEC 62614-1:2020

IEC 62614-1: 2020 describes the launch condition requirements used for measuring multimode attenuation in passive components and in installed cable plants. In this document, the fibre types that are addressed include category A1-OMx, where x = 2, 3, 4 and 5 (50 µm/125 µm), and A1-OM1 (62,5 µm/125 µm) multimode fibres, as specified in IEC 60793-2-10. The nominal test wavelengths detailed are 850 nm and 1 300 nm. This document can be suitable for multimode attenuation measurements for other multimode categories and/or other wavelengths, but the source condition for other categories and wavelengths are not defined here. The purpose of these requirements is as follows:  to ensure consistency of field measurements when different types of test equipment are used; to ensure consistency of factory measurements when different types of test equipment are used; to ensure consistency of field measurements when compared with factory measurements.  This document describes launch condition requirements for optical attenuation using sources with a controlled encircled flux (EF).

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day