CLC/SR 86C - Fibre optic systems and active devices

IEC 61280-2-13:2024 series defines a procedure for calculating the root-mean-square error vector magnitude of optical n-APSK signals from a set of measured symbols. It specifically defines the normalization of the reference states and a procedure for optimal scaling of the measured symbol states. The procedure described in this document applies to single-polarized optical signals as well as to conventional polarization-multiplexed signals with independently modulated polarization tributaries. In general, it is not advisable to apply these procedures without modification to signals, in which optical amplitude, phase, and polarization state are simultaneously modulated to encode the information data. This document does not specify any signal processing steps for extracting the symbols from the received optical signals, because these steps depend on the optical receiver and can vary with the type of the transmitted n-APSK signal. These and optional additional signal processing steps are defined in application-specific documents.

IEC 61280-4-2:2024 is available as IEC 61280-4-2:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62180-4-2:2024 is applicable to the measurements of attenuation and optical return loss of an installed optical fibre cabling plant using single-mode fibre. This cabling plant can include single-mode optical fibres, connectors, adapters, splices, and other passive devices. The cabling can be installed in a variety of environments including residential, commercial, industrial and data centre premises, as well as outside plant environments. This document is applicable to all single-mode fibre types including those designated by IEC 60793-2-50 as Class B fibres. The principles of this document can be applied to cabling plants containing branching devices (splitters) and at specific wavelength ranges in situations where passive wavelength selective components are deployed, such as WDM, CWDM and DWDM devices. This document is not intended to apply to cabling plants that include active devices such as fibre amplifiers or dynamic channel equalizers. This third edition cancels and replaces the second edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of the equipment cord method; b) addition of test limit adjustment related to test cord grades; c) refinements on measurement uncertainties.

IEC 61757-7-3:2024 defines the terminology, structure, and performance characteristics of fibre optic voltage sensors using a polarimetric measurement method. The document specifies test methods and procedures for measuring key performance parameters of these sensors. It addresses only the voltage sensing element and not the additional devices that are unique to each application. The document does not specify the required performance values of optical polarimetric fibre optic voltage sensors, because these specifications depend on the designated application of the sensor and are typically defined by the user of the sensor. The required performance values are usually defined when designing a sensor for a specific application.

IEC 61757-6-1:2024 defines the terminology, structure, and measurement methods of optical displacement sensors based on fibre Bragg gratings (FBGs) as the sensing element. This document also specifies the most important features and characteristics of these fibre optic displacement sensors and defines procedures for measuring these features and characteristics.

IEC 62148-17: 2023 defines physical interface specifications for transmitter and receiver components with dual coaxial RF connectors. This second edition cancels and replaces the first edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) IEC 61169-60 was added as a normative reference for SMPM connectors; b) normative reference IEC 60874-1 (withdrawn) was replaced by IEC 61754 (all parts); c) a reference to the terms and definitions of IEC 62007-1 was added in Clause 3; d) a new column “Typical” was added to the tables in Figure 2 and Figure 3 to clarify the meaning of all listed values.

IEC 61757-1-2: 2023 defines detailed specifications for distributed strain measurements with a fibre optic sensor, also known as "fibre optic distributed strain sensing". It is applicable to distributed strain sensing systems (DSS) based on spontaneous or stimulated Brillouin scattering in the optical fibre sensor (strain sensitive element), that is, to sensors capable of measuring absolute strain. This document specifies the most important DSS performance parameters and defines the procedures for their determination.

IEC 62149-3: 2023 covers the performance specification for electroabsorption (EA) type optical modulators monolithically integrated with laser diodes for 40 Gbit/s fibre optic transmission systems. This document contains definitions for product performance requirements as well as a series of tests and measurements, for which clearly defined conditions, severities and pass/fail criteria are provided. The tests are intended to be run as an initial design verification to prove any product's ability to satisfy this document's requirements. This document is applicable for on-off keying modulation formats. A product that has been shown to meet all the requirements of a performance standard can be declared as compliant with the performance standard but will then be controlled by a quality assurance program. This fourth edition cancels and replaces the third edition published in 2020. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) specification of pull force for fibre pull test in Table 6 according to fibre type; b) change of symbol for kink free radiant power in Table 4 and Table 5; c) replacement of undefined symbols in Table 7; d) addition of IEC 62149-1 as a normative reference.

IEC 61291-2:2023 is available as IEC 61291-2:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61292-2:2023 provides a performance specification template applicable to optical amplifiers (OAs) used in single channel applications. Multichannel applications are covered in IEC 61291-4. The objective of this template is to provide a framework for the preparation of performance standards and/or product specifications defining the performance of OA devices used in single channel applications. In addition to the requirements specified in this template, a performance standard or product specification could include other parameters, such as ratings, operating conditions, tests, and pass/fail criteria. For a particular application, product specification writers could add specification parameters and/or groups of specification parameters to this template, without removing the parameters specified in this document. This fifth edition cancels and replaces the fourth edition published in 2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the test methods for gain ripple in Table 2, Table 4 and Table 6 refer now to the IEC 61290‑1 series; - the SOA definition (3.1.3) refers now to IEC 61931.

IEC 62148-22: 2023 defines the physical dimensions and interface specifications for directly modulated laser (DML) devices used in optical telecommunication and optical data transmission applications. The intent of this document is to adequately specify the physical requirements for DML devices so as to enable mechanical interchangeability of laser devices or transmitters complying with this document both at the printed circuit board and for any panel-mounting requirements.

IEC 62149-12:2023 This part of IEC 62149 defines performance specifications for distributed feedback laser diode (DFB-LD) devices used in analogue radio over fibre (RoF) systems. It defines product performance requirements together with a series of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a “once-off” basis to prove a product’s ability to satisfy the performance requirements.

IEC 61280-1-4:2023 is available as IEC 61280-1-4:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61280-1-4:2023 establishes the characterization process of the encircled flux measurement method of light sources intended to be used with multimode fibre. This document sets forth a procedure for the collection of two-dimensional fibre optic nearfield greyscale data and subsequent reduction to one-dimensional data expressed as a set of three sampled parametric functions of radius from the fibre’s optical centre. Estimation of the fibre core diameter is not an objective of this document. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - improvement of calibration procedure and calibration traceability; - improvement of fibre shaker description and requirements; - addition of pulsed light sources; - removal of a poorly traceable calibration process using a micro positioner.

IEC 62343:2023 is available as IEC 62343:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62343:2023 applies to all commercially available optical dynamic modules and devices. It describes the products covered by the IEC 62343 series, defines terminology, fundamental considerations and basic approaches. The object of this document is to: - establish uniform requirements for operation, reliability and environmental properties of dynamic modules (DMs) to be implemented in the appropriate DM standard, and - provide assistance to the purchaser in the selection of consistently high-quality DM products for their particular applications, as well as in the consultation of the appropriate specific DM standard(s). This document covers performance templates, performance standards, reliability qualification requirements, hardware and software interfaces and related testing methods. Since a dynamic module integrates an optical module/device, printed wiring board, and software/firmware, the standards developed in the series will mimic appropriate existing standards. On the other hand, since "dynamic module" is a relatively new product category, the dynamic module standards series will not be bound by the existing practices where requirements differ.The safety standards as related to dynamic modules are mostly optical power considerations, which is covered by the IEC 60825 series (see Clause 6). This third edition cancels and replaces the second edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - addition of terms and definitions for optical multicast switches (3.8); - revision of Clause 4, listing the requirements for standards in the IEC 62343 series; - addition of Clause 6 (Safety requirements).

IEC 62149-4:2022 is available as IEC 62149-4:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62149-4:2022 defines performance specifications for 1 300 nm fibre optic transceiver modules used for the ISO/IEC/IEEE 8802-3 Gigabit Ethernet application. This document contains definitions for product performance requirements as well as a series of tests and measurements, for which clearly defined conditions, severities and pass/fail criteria are provided. The tests are intended to be run on a "once-off" basis to prove any product’s ability to satisfy the performance standard’s requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard but will then be controlled by a quality assurance/quality conformance program. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the normative references are updated; - the condition "for short periods" in 4.1 is removed; - the absolute limiting rating for soldering temperature in Table 1 is modified; - the maximal optical output power (multimode fibre) in Table 4 is increased from −3,5 dBm to −3 dBm, to align value with the referenced document; - a note is added to Table 7 to clarify that out-of-specification products are not allowed to pass the performance tests.

IEC Corrected version

IEC 62343-2-1:2019 provides a reliability qualification test template for dynamic modules (DMs). The template describes the reliability qualification test items and provides information on requirements or options. Example test conditions are given for information purposes in Annex A. For reliability qualification purposes, some information about the internal components, parts and interconnections is needed. These internal parts are treated as black boxes. This document gives requirements for the evaluation of DM reliability by combining the reliability of such internal black boxes. The object of this reliability qualification test template is to provide a framework for the reliability qualification tests for DMs. Developers of reliability qualification tests for DMs determine the test conditions for each test item by referring to the examples in Annex A. Keywords: dynamic modules (DMs), test requirements for DMs

IEC 61280-4-3: 2022 describes the measurement of attenuation, optical return loss and optical power in installed passive optical networks (PONs) using single-mode fibre. This document specifies two methods for measuring the attenuation before activation of the PON:  
method A: one-cord method using a light source and a power meter (LSPM);
method B: optical time-domain reflectometer (OTDR) method in upstream direction only, with reduction of uncertainties due to the variation of backscatter coefficient.  In addition, method C, which is described in informative Annex C, provides an estimate of the attenuation after partial activation of the PON by using a U band filtered optical time-domain reflectometer (FOTDR) in an upstream direction. This publication contains an attached file titled "Supplemental Data" in the form of an Excel spread sheet. This file is intended to be used as a complement and does not form an integral part of the standard.

IEC 61290-1:2022 is available as IEC 61290-1:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61290-1:2022 applies to all commercially available optical amplifiers (OAs) and optically amplified subsystems. It applies to OAs using optically pumped fibres (optical fibre amplifiers (OFAs) based on either rare-earth doped fibres or on the Raman effect), semiconductors (semiconductor optical amplifiers (SOAs)), and aveguides (planar optical waveguide amplifiers (POWAs)). It is specifically directed to single-channel amplifiers. Test methods for multichannel amplifiers are defined in the IEC 61290-10 series. This document establishes uniform requirements for accurate and reliable measurements of the following OA parameters, as defined in IEC 61291-1:2018, Clause 3: a) nominal output signal power; b) gain; c) reverse gain; d) maximum gain; e) maximum gain wavelength; f) maximum gain variation with temperature; g) gain wavelength band; h) gain wavelength variation; i) gain stability; j) polarization-dependent gain; k) gain ripple (SOA only); l) large-signal output stability; m) saturation output power; n) maximum output signal power; o) maximum total output power. NOTE 1 The applicability of the test methods described in this document to distributed Raman amplifiers is still under study. NOTE 2 All numerical values followed by (‡) are suggested values for which the measurement is assured. Other values are acceptable if verified. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - specification of gain ripple as a new parameter; - specification of test method and test report for gain ripple measurements; - use of the term “measurement uncertainty” instead of “measurement accuracy”.

IEC Corrected version

IEC 61280-4-1: 2019 is applicable to the measurement of attenuation of installed optical fibre cabling plant using multimode optical fibre. This cabling plant can include multimode optical fibres, connectors, adapters, splices, and other passive devices. The cabling can be installed in a variety of environments including residential, commercial, industrial, and data centre premises, as well as outside plant environments. The test equipment used in this document has one single fibre connector interface or two single fibre connector interfaces. In this document, the optical fibres that are addressed include sub-categories A1-OMx, where x = 2, 3, 4 and 5 (50/125 μm) and A1-OM1 (62,5/125 μm) multimode optical fibres, as specified in IEC 60793-2-10. The attenuation measurements of the other multimode categories can be made using the approaches of this document, but the source conditions for the other categories have not been defined. This third edition cancels and replaces the second edition, published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) changes to Annex F on encircled flux to harmonise with IEC TR 62614-2, but keeping the encircled flux limits defined in Tables F.2 to F.5 unchanged; b) addition of an equipment cord method in Annex D; c) inclusion of testing bend insensitive multimode optical fibre; d) updates to measurement uncertainty; e) definition of additional cabling configurations; f) changes to Table 5 on spectral requirements. Keywords: measurement of attenuation

IEC 62148-19: 2019 covers the photonic chip scale package. The purpose of this document is to specify adequately the physical requirements of optical transmitters and receivers that will enable mechanical interchangeability of transmitters and receivers. Keywords: physical interface for photonic chip scale packages

This part of IEC 61757 specifies terminology, characteristic performance parameters, related test and calculation methods, and specific test equipment for interrogation units used in distributed fibre optic acoustic sensing and vibration measurement systems. This document refers to Rayleigh backscatter and phase detection method by phase-sensitive coherent optical time-domain reflectometry (ϕ-OTDR) only. Quasi-static and low frequency operation modes are not covered by this document. Generic specifications for fibre optic sensors are defined in IEC 61757.

This document provides general conditions for the standard performance of optical dynamic modules. All performance standards of dynamic modules are based on the general conditions defined in this document. Additional conditions are included in individual performance standards.

This part of IEC 62150 specifies a generic mezzanine board system to support test and measurement of devices based on micro-optical and micro-photonic technologies, including but not limited to photonic integrated circuit (PIC) devices.

IEC Corrected version

This part of IEC 62149 covers the performance specification for radio-over-fibre (RoF) transceivers used for mobile fronthaul systems. The performance standard contains a definition of the product performance requirements together with a series of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a one-off basis to prove any product's ability to satisfy the performance standard's requirements. A product that has been shown to meet all the requirements of a performance standard canbe declared to be in compliance with the performance standard.

IEC 61757:2018 is a generic specification covering optical fibres, components and sub-assemblies as they pertain specifically to fibre optic sensing applications. It has been designed to be used as a common working and discussion tool by the vendors of components and subassemblies intended to be integrated in fibre optic sensors, as well as by designers, manufacturers and users of fibre optic sensors independent of any application or installation. The objective of this document is to define, classify and provide the framework for specifying fibre optic sensors, and their specific components and subassemblies. The requirements of this document apply to all related fibre optic sensor standards which belong to IEC 61757 (all parts). Standards of IEC 61757 (all parts) contain requirements specific to sensors for particular quantities subject to measurement, and for a particular style or variant of such a fibre optic sensor. Keywords: fibre optic sensors

This part of the IEC 61757 series specifies terminology, characteristic performance parameters and related test methods of optical temperature sensors based on fibre Bragg gratings (FBG) carrying out temperature measurements in the temperature range between -260 °C and 600 °C. Generic specifications for fibre optic sensors are defined in IEC 61757.

This document defines terminology, structure, characteristics and their measurement method including the procedures for an optical tilt sensor based on fibre Bragg gratings (FBGs) as the sensitive element.

This part of IEC 61280 provides definitions and measurement procedures for several wavelength and spectral width properties of an optical spectrum associated with a fibre optic communication subsystem, an optical transmitter, or other light sources used in the operation or test of communication subsystems. This document also provides definitions and measurement procedures for side mode suppression ratio and signal to source spontaneous emission ratio. The measurement is done for the purpose of system construction and/or maintenance. In the case of communication subsystem signals, the optical transmitter is typically under modulation. NOTE Different properties may be appropriate to different spectral types, such as continuous spectra characteristic of light-emitting diodes (LEDs), and multilongitudinal-mode (MLM), multitransverse-mode (MTM) and single-longitudinal mode (SLM) spectra, characteristic of laser diodes (LDs).

IEC 62148-21:2021 is available as IEC 62148-21:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62148-21: 2021 covers the design guidelines of the electrical interface for photonic integrated circuit (PIC) packages using silicon fine-pitch ball grid array (S-FBGA) and silicon fine-pitch land grid array (S-FLGA). In this document, the electrical interface for the S-FBGA package is informative. The purpose of this document is to specify adequately the electrical interface of PIC packages composed of optical transmitters and receivers that enable mechanical and electrical interchangeability of PIC packages. This second edition cancels and replaces the first edition published in 2019. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: specification of an electric guard band area around the optical terminal area, so as to allow applications with electric signals at higher symbol rates (e.g. 50 Gbaud and 100 Gbaud).

IEC 61290-4-3:2018 applies to output power controlled optically amplified, elementary sub‑systems. It applies to optical fibre amplifiers (OFAs) using active fibres containing rare‑earth dopants, presently commercially available, as indicated in IEC 61291-1, as well as alternative optical amplifiers that can be used for single channel output power controlled operation, such as semiconductor optical amplifiers (SOAs). The object of this document is to provide the general background for optical amplifiers (OAs) power transients and their measurements and to indicate those IEC standard test methods for accurate and reliable measurements of the following transient parameters: a) transient power response; b) transient power overcompensation response; c) steady-state power offset; d) transient power response time. The stimulus and responses behaviours under consideration include the following: 1. channel power increase (step transient); 2. channel power reduction (inverse step transient); 3. channel power increase/reduction (pulse transient); 4. channel power reduction/increase (inverse pulse transient); 5. channel power increase/reduction/increase (lightning bolt transient); 6. channel power reduction/increase/reduction (inverse lightning bolt transient). These parameters have been included to provide a complete description of the transient behaviour of an output power transient controlled OA. The test definitions defined here are applicable if the amplifier is an OFA or an alternative OA. However, the description in Annex A concentrates on the physical performance of an OFA and provides a detailed description of the behaviour of an OFA; it does not give a similar description of other OA types. Annex B provides a detailed description background of the dynamic phenomenon in output power controlled amplifiers under transient conditions and Annex C details the impact of speed of transient inputs.This second edition cancels and replaces the first edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: alignment of the measure of amplified spontaneous emission (ASE) relative to signal power with the definition in IEC 61290-3-3. Keywords: optical amplifiers (OAs) power transients This International Standard is to be used in conjunction with IEC 61291-1:2012

IEC 62343-3-4: 2018 provides a performance specification template for multicast optical switches. The object is to provide a framework for the preparation of performance specifications or product specifications of multicast optical switches. Specification parameters required in this document are considered as essential in the product specifications or performance specifications. Keywords: multicast optical switch (MCOS)

IEC 62148-15:2021 is available as IEC 62148-15:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62148-15:2021 covers the physical dimension and interface specifications for discrete vertical cavity surface emitting laser (VCSEL) devices in optical telecommunication and optical data transmission applications. The intent of this document is to adequately specify the physical requirements of VCSEL devices that will enable mechanical interchangeability of laser devices or transmitters complying with this document both at the printed circuit wiring board and for any panel-mounting requirement. This third edition cancels and replaces the second edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the classification of optical/electrical interface types is generalized and referred to IEC 62148-1; - a new pin mode is added to Table 1; - several dimensions of the VCSEL TO CAN package are changed in Table 3 to reflect the current state of technology; - Figure 7 is updated to show the complete details of the VCSEL TOSA package.

IEC 61280-2-8:2021 is available as IEC 61280-2-8:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61280-2-8:2021 specifies two main methods for the determination of low BER values by making accelerated measurements. These include the variable decision threshold method (Clause 5) and the variable optical threshold method (Clause 6). In addition, a third method, the sinusoidal interference method, is described in Annex B. This second edition cancels and replaces the first edition published in 2003. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - correction of errors in Formula (8) in 5.5.2 and in a related formula in 5.5.3; - correction of errors in the references to clauses, subclauses, figures, procedures, and in the Bibliography; - alignment of the terms and definitions in 3.1 with those in IEC 61281-1.

IEC 61290-1-3:2021 is available as IEC 61290-1-3:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61290-1-3:2021 applies to all commercially available optical amplifiers (OA) and optically amplified subsystems. It applies to OA using optically pumped fibres (OFA based on either rare-earth doped fibres or on the Raman effect), semiconductors (SOA), and waveguides (POWA). NOTE 1 The applicability of the test methods described in this document to distributed Raman amplifiers is for further study. The object of this document is to establish uniform requirements for accurate and reliable measurements, by means of the optical power meter test method, of the following OA parameters, as defined in IEC 61291-1: - nominal output signal power; - gain; - polarization-dependent gain; - maximum output signal power; - maximum total output power. NOTE 2 All numerical values followed by (‡) are suggested values for which the measurement is assured. Other values can be acceptable upon verification. This document applies to single-channel amplifiers. For multichannel amplifiers, IEC 61290-10 (all parts) applies. This fourth edition cancels and replaces the third edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - harmonization with IEC 61290-1-1; - use of the term "measurement uncertainty" instead of "measurement accuracy".

IEC 61291-1:2018 applies to all commercially available optical amplifiers (OAs) and optically amplified assemblies. It applies to OAs using optically pumped fibres (OFAs based either on rare-earth doped fibres or on the Raman effect), semiconductors (SOAs), and waveguides (POWAs). The object of this document is - to establish uniform requirements for transmission, operation, reliability and environmental properties of OAs, and - to provide assistance to the purchaser in the selection of consistently high-quality OA products for his particular applications. Parameters specified for OAs are those characterizing the transmission, operation, reliability and environmental properties of the OA seen as a "black box" from a general point of view. In the sectional and detail specifications a subset of these parameters will be specified according to the type and application of the particular OA device or assembly. This fourth edition cancels and replaces the third edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - terms have been added for parameters from IEC 61290-4-3 and IEC 61290-10-5; - Clause 4 Classification has been removed, since this system is judged to be unused; - the definition of polarization mode dispersion (PMD) has been simplified. Keywords: optical amplifiers (OAs)

IEC Corrected version.

IEC 62343-5-2:2018 describes the measurement methods of dynamic crosstalk during port switching for 1 x N fixed-grid wavelength selective switches (WSSs). The objective of this document is to establish a standard test method for different-channel dynamic crosstalk and same-channel dynamic crosstalk that occur when a particular optical channel signal is switched to the specific branching port against a common port in ITU‑T 50 GHz and 100 GHz fixed grid 1 x N (N ≥ 3) WSSs.

IEC 62148-1:2017(E) aims to assure interchangeability in physical interfaces between fibre optic active components and devices supplied by different manufacturers, but it does not guarantee operation between such devices. This second edition cancels and replaces the first edition, published in 2002, and constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: addition of a free space optical coupling interface in Clause 5. Keywords: physical interfaces between fibre optic components

IEC 61281-1:2017 is a generic specification for fibre optic communication subsystems (FOCSs). The parameters defined herein form a specifiable minimum set of specifications that are common to all fibre optic subsystems. Additional parameters can be used depending on the particular application and technology. Those additional parameters will be specified in the relevant documents, as appropriate. Each specified parameter is measured using one of the test procedures. The use of these parameters for system design is given in design guides. This second edition cancels and replaces the first edition published in 1999. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: addition of new definitions. Keywords: fibre optic communication subsystems (FOCSs)

IEC 61290-1-1:2020 is available as IEC 61290-1-1:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61290-1-1:2020 applies to all commercially available optical amplifiers (OAs) and optically amplified modules. It applies to OAs using optical fibre amplifiers (OFAs) based on either rare-earth doped fibres or on the Raman effect, semiconductor OAs (SOAs) and planar optical waveguide amplifiers (POWAs). The object of this document is to establish uniform requirements for accurate and reliable measurements, by means of the optical spectrum analyzer (OSA) test method, of the following OA parameters, as defined in IEC 61291-1: - nominal output signal power; - gain; - polarization-dependent gain (PDG); - maximum output signal power; - maximum total output power. In addition, this document provides the test method of: - gain ripple (for SOAs). NOTE All numerical values followed by (‡) are suggested values for which the measurement is assured. The object of this document is specifically directed to single-channel amplifiers. Test methods for multichannel amplifiers are standardized in IEC 61290-10 (all parts). This fourth edition cancels and replaces the third edition published in 2015 and constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: addition of techniques to test gain ripple of SOAs.

IEC 62343:2017(E) applies to all commercially available optical dynamic modules and devices. It describes the products covered by the IEC 62343 series, defines terminology, fundamental considerations and basic approaches. The object of this document is to: establish uniform requirements for operation, reliability and environmental properties of dynamic modules (DMs) to be implemented in the appropriate DM standard, and provide assistance to the purchaser in the selection of consistently high-quality DM products for his particular applications, as well as in the consultation of the appropriate specific DM standard(s). This document covers performance templates, performance standards, reliability qualification requirements, hardware and software interfaces and related testing methods. Since a dynamic module integrates an optical module/device, printed wiring board, and software/firmware, the standards developed in the series will mimic appropriate existing standards. On the other hand, since "dynamic module" is a relatively new product category, the dynamic module standards series will not be bounded by the existing practices where requirements differ. The safety standards as related to dynamic modules are mostly optical power considerations, which is covered by IEC TC 76: Optical radiation safety and laser equipment. This second edition cancels and replaces the first edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: the inclusion of definitions for the wavelength selective switch.

IEC 61757-2-2:2016(E) defines detail specifications for distributed temperature measurement by a fibre optic sensor, also known as fibre optic distributed temperature sensing (DTS). DTS includes the use of Raman scattering, Brillouin scattering and Rayleigh scattering effects. In addition, Raman scattering and Rayleigh scattering based measurements are performed with a single-ended fibre configuration only. Brillouin scattering based measurements are performed with a single-ended fibre or fibre loop configuration. The technique accessible from both sides at same time (e. g. Brillouin optical time domain analysis, BOTDA) is referred to here as a loop configuration. Generic specifications for fibre optic sensors are defined in IEC 61757-1:2012. This part of IEC 61757 specifies the most important DTS performance parameters and defines the procedures for their determination. In addition to the group of performance parameters, a list of additional parameters has been defined to support the definition of the measurement specifications and their associated test procedures. The definitions of these additional parameters are provided for informational purposes and should be included with the sets of performance parameters. A general test setup is defined in which all parameters can be gathered through a set of tests. The specific tests are described within the clause for each measurement parameter. This general test setup is depicted and described in Clause 4 along with a list of general information that should be documented based upon the specific DTS instrument and test setup used to measure these parameters as per IEC 61757-2-2. Annex A provides a blank performance parameter table which should be used to record the performance parameter values for a given DTS instrument and chosen optical test setup configuration. Annex B provides guidelines for optional determination of point defect effects. Keywords: fibre optic distributed temperature sensing (DTS) This publication is to be read in conjunction with IEC 61757-1:2012

IEC 62149-5:2020 is available as IEC 62149-5:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62149-5:2020 specifies performance on the transceiver modules for asynchronous-transfer-mode passive optical network (ATM-PON) systems recommended by the International Telecommunication Union (ITU) in ITU-T Recommendation G.983.1. This third edition cancels and replaces the second edition published in 2009 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - description of types in Clause 4 has been removed; - titles of reference documents have been updated.

IEC 62149-3:2014 covers the performance specification for optical modulators monolithically integrated with laser diodes for 2,5 Gbit/s to 40 Gbit/s multi-channel fibre optic transmission systems. This performance standard contains a definition of the product performance requirements together with a series of sets of tests and measurements with clearly defined conditions, severities and pass/fail criteria. The tests are intended to be run as an initial design verification to prove any product's ability to satisfy the performance standard's requirements. This standard is only applicable for on-off keying format. This second edition cancels and replaces the first edition published in 2004 and constitutes a technical revision. The significant technical change with respect to the previous edition is as follows: The performance standards covered by this standard are now extended to a 40 Gb/s-class system from their original 2,5 Gb/s. Keywords: optical modulators monolithically integrated, laser diodes, 2,5 Gbit/s to 40 Gbit/s multi-channel fibre optic transmission systems