EN 62343-1-3:2006

Dynamic modules - Part 1-3: Performance standards - Dynamic gain tilt equalizer with pigtails for use in controlled environments (Category C)

This standard contains the minimum initialization test and measurement requirements and severities which a dynamic gain tilt equalizer (DGTE) shall satisfy in order to be categorized as meeting the requirements of a DGTE used in controlled environments. The requirements cover dynamic gain equalizers for category C - Controlled environments.

Dynamische Module - Teil 1-3: Betriebsverhalten - Equalizer zur Kompensation einer dynamischen Kennlinie mit Anschlussfasern für den Einsatz in kontrollierter Umgebung (Kategorie C)

Modules dynamiques - Partie 1-3: Normes de qualité de fonctionnement - Egaliseur dynamique de basculement de gain avec fibres amorces destiné à être utilisé dans des environnements contrôlés (Catégorie C)

La présente norme contient les sévérités et les exigences minimales d'essai d'initialisation et de mesure qu'un égaliseur dynamique de basculement de gain (Dynamic Gain Tilt Equalizer - DGTE) doit satisfaire afin d'être classé comme conforme aux exigences applicables aux DGTE pour une utilisation dans des environnements contrôlés. Ces exigences couvrent les égaliseurs dynamiques de gain pour la catégorie C - Environnements contrôlés.

Dinamični elementi - 1-3. del: Standardi lastnosti - Izenačevalnik dinamične ojačitve s spojitvenimi vlakni za uporabo v nadzorovanem okolju (IEC 62343-1-3:2006)

General Information

• Status: Withdrawn
• Publication Date: 12-Dec-2006
• Withdrawal Date: 31-Oct-2009
• ICS: 33.180.01 - Fibre optic systems in general
• ICS: 33.180.99 - Other fibre optic equipment
• Technical Committee: CLC/SR 86C - Fibre optic systems and active devices
• Drafting Committee: IEC/SC 86C - IEC_SC_86C
• Parallel Committee: IEC/SC 86C - IEC_SC_86C
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 09-Jan-2016
• Completion Date: 09-Jan-2016
• Ref Project: SIST EN 62343-1-3:2007 - Dynamic modules -- Part 1-3: Performance standards - Dynamic gain tilt equalizer with pigtails for use in controlled environments (Category C)

Relations

• Replaced By: EN 62343-1-3:2013 - Dynamic modules - Part 1-3: Performance standards - Dynamic gain tilt equalizer (non-connectorized)
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2007
'LQDPLþQLHOHPHQWL±GHO6WDQGDUGLODVWQRVWL±,]HQDþHYDOQLNGLQDPLþQH
RMDþLWYHVVSRMLWYHQLPLYODNQL]DXSRUDERYQDG]RURYDQHPRNROMX,(&

Dynamic modules -- Part 1-3: Performance standards - Dynamic gain tilt equalizer with
pigtails for use in controlled environments (Category C) (IEC 62343-1-3:2006)
Dynamische Module -- Teil 1-3: Betriebsverhalten - Equalizer zur Kompensation einer
dynamischen Kennlinie mit Anschlussfasern für den Einsatz in kontrollierter Umgebung
(Kategorie C) (IEC 62343-1-3:2006)
Modules dynamiques -- Partie 1-3: Normes de qualité de fonctionnement - Egaliseur
dynamique de basculement de gain avec fibres amorces destiné a etre utilisé dans des
environnements contrôlés (Catégorie C) (IEC 62343-1-3:2006)
Ta slovenski standard je istoveten z: EN 62343-1-3:2006
ICS:
33.180.30 2SWLþQLRMDþHYDOQLNL Optic amplifiers
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 62343-1-3
NORME EUROPÉENNE
December 2006
EUROPÄISCHE NORM
ICS 33.180.01; 33.180.99
English version
Dynamic modules
Part 1-3: Performance standards -
Dynamic gain tilt equalizer with pigtails
for use in controlled environments (Category C)
(IEC 62343-1-3:2006)
Modules dynamiques  Dynamische Module
Partie 1-3: Normes de qualité Teil 1-3: Betriebsverhalten -
de fonctionnement - Equalizer zur Kompensation
Egaliseur dynamique de basculement einer dynamischen Kennlinie
de gain avec fibres amorces destiné mit Anschlussfasern für den Einsatz
à être utilisé dans des environnements in kontrollierter Umgebung (Kategorie C)
contrôlés (Catégorie C) (IEC 62343-1-3:2006)
(CEI 62343-1-3:2006)
This European Standard was approved by CENELEC on 2006-11-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62343-1-3:2006 E
Foreword
The text of document 86C/722/FDIS, future edition 1 of IEC 62343-1-3, prepared by SC 86C, Fibre optic
systems and active devices, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as EN 62343-1-3 on 2006-11-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2007-08-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2009-11-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62343-1-3:2006 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 62343-1-3:2006
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

1) 2)
IEC 61300-2-1 - Fibre optic interconnecting devices and EN 61300-2-1 2003
passive components - Basic test and
measurement procedures
Part 2-1: Tests - Vibration (sinusoidal)

1) 2)
IEC 61300-2-4 - Fibre optic interconnecting devices and EN 61300-2-4 1997
passive components - Basic test and
measurement procedures
Part 2-4: Tests - Fibre/cable retention

1) 2)
IEC 61300-2-9 - Fibre optic interconnecting devices and EN 61300-2-9 1997
passive components - Basic test and
measurement procedures
Part 2-9: Tests - Shock
1) 2)
IEC 61300-2-14 - Fibre optic interconnecting devices and EN 61300-2-14 2006
passive components - Basic test and
measurement procedures
Part 2-14: Tests - Optical power handling and
damage threshold characterization

1) 2)
IEC 61300-2-17 - Fibre optic interconnecting devices and EN 61300-2-17 2003
passive components - Basic test and
measurement procedures
Part 2-17: Tests - Cold
1) 2)
IEC 61300-2-18 - Fibre optic interconnecting devices and EN 61300-2-18 2005
passive components - Basic test and
measurement procedures
Part 2-18: Tests - Dry heat - High
temperature endurance
1) 2)
IEC 61300-2-19 - Fibre optic interconnecting devices and EN 61300-2-19 2005
passive components - Basic test and
measurement procedures
Part 2-19: Tests - Damp heat (steady state)

1)
Undated reference.
2)
Valid edition at date of issue.

Publication Year Title EN/HD Year
1) 2)
IEC 61300-2-22 - Fibre optic interconnecting devices and EN 61300-2-22 1997
passive components - Basic test and
measurement procedures
Part 2-22: Tests - Change of temperature

1) 2)
IEC 61300-2-42 - Fibre optic interconnecting devices and EN 61300-2-42 2005
passive components - Basic test and
measurement procedures
Part 2-42: Tests - Static side load for
connectors
1) 2)
IEC 61300-3-2 - Fibre optic interconnecting devices and EN 61300-3-2 1999
passive components - Basic tests and
measurement procedures
Part 3-2: Examinations and measurements -
Polarization dependence of attenuation in a
single-mode fibre optic device

1) 2)
IEC 61300-3-5 - Fibre optic interconnecting devices and EN 61300-3-5 2001
passive components - Basic test and
measurement procedures
Part 3-5: Examinations and measurements -
Wavelength dependence of attenuation

1) 2)
IEC 61300-3-6 - Fibre optic interconnecting devices and EN 61300-3-6 2003
passive components - Basic test and
measurement procedures
Part 3-6: Examinations and measurements -
Return loss
1) 2)
IEC 61300-3-32 - Fibre optic interconnecting devices and EN 61300-3-32 2006
passive components - Basic test and
measurement procedures
Part 3-32: Examinations and measurements -
Polarisation mode dispersion measurement
for passive optical components

3)
IEC 61300-3-38 - Fibre optic interconnecting devices and - -
passive components - Basic test and
measurement procedures
Part 3-38: Examinations and measurements -
Measurement techniques for determination of
the group delay and chromatic dispersion of
passive components used in fibre optic
communication systems
1) 2)
IEC 61753-021-2 - Fibre optic interconnecting devices and EN 61753-021-2 2002
passive component performance standard
Part 021-2: Fibre optic connectors terminated
on single-mode fibre for category C -
Controlled environment
3)
Under consideration.
- 5 - EN 62343-1-3:2006
Publication Year Title EN/HD Year
1) 2)
IEC 61753-022-2 - Fibre optic interconnecting devices and EN 61753-022-2 2003
passive components performance standard
Part 022-2: Fibre optic connectors terminated
on multimode fibre for category C - Controlled
environment
1)
ITU-T - Optical interfaces for multichannel systems - -
Recommendation with optical amplifiers
G.692
NORME CEI
INTERNATIONALE
IEC
62343-1-3
INTERNATIONAL
Première édition
STANDARD
First edition
2006-10
Modules dynamiques –
Partie 1-3:
Normes de qualité de fonctionnement –
Egaliseur dynamique de basculement de gain
avec fibres amorces destiné à être utilisé dans
des environnements contrôlés (Catégorie C)

Dynamic modules –
Part 1-3:
Performance standards –
Dynamic gain tilt equalizer with pigtails for
use in controlled environments (Category C)
© IEC 2006 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
CODE PRIX
M
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

62343-1-3 © IEC:2006 – 3 –
CONTENTS
FOREWORD.5

1 Scope.9
2 Normative references .9
3 Terms and definitions .11
4 Test.13
5 Spectral bands .15
6 Test report.15
7 Reference components.15
8 Performance requirements .15

Bibliography.25

Table 1 – Spectral bands for single-mode systems .15
Table 2 – Test details and requirements .17

62343-1-3 © IEC:2006 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DYNAMIC MODULES –
Part 1-3: Performance standards –
Dynamic gain tilt equalizer with pigtails for use
in controlled environments (Category C)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, o
...