EN 62343-1-3:2013

Dynamic modules - Part 1-3: Performance standards - Dynamic gain tilt equalizer (non-connectorized)

IEC 62343-1-3:2012 contains the guideline minimum initialization test and measurement requirements and severities, for a dynamic gain tilt equalizer (DGTE). This second edition cancels and replaces the first edition published in 2006. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - a change in the title removing the environmental category; - the addition of Clause 4, Operating and storage conditions; - the inclusion of spectral bands in Clause 5, Test; - a definition of the wavelength range for test requirements in Clause 5, Test; - the removal of the environment tests from the test details and requirements. Keywords: initialization test, measurement requirements, dynamic gain tilt equalizer (DGTE)

Dynamische Module - Teil 1-3: Betriebsverhalten - Dynamischer Equalizer mit Schräglagen Verstärkung (nicht mit Steckern versehen)

Modules dynamiques - Partie 1-3: Normes de performance - Egaliseur dynamique de basculement de gain (non-connectorisé)

La CEI 62343-1-3:2012 contient les lignes directrices concernant les exigences et sévérités d'essai et de mesure initiales minimales relatives aux égaliseurs dynamiques de basculement de gain (DGTE). Cette deuxième édition annule et remplace la première édition publiée en 2006. Elle constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - une modification du titre en supprimant la catégorie d'environnement; - ajout d'un Article 4, Conditions de fonctionnement et de stockage; - inclusion de la partie bandes spectrales dans l'Article 5, Essais; - définition de la plage de longueurs d'onde pour les exigences d'essais à l'Article 5, Essais; - suppression des essais d'environnement des exigences et détails d'essai. Mots clés: essai et mesure initiale, dynamique de basculement de gain (DGTE)

Dinamični elementi - 1-3. del: Standardi lastnosti - Izenačevalnik dinamične ojačitve s spojitvenimi vlakni za uporabo v nadzorovanem okolju (IEC 62343-1-3:2012)

Ta del standarda IEC 62343 vsebuje smernice za najmanjše začetne zahteve in stopnje zahtevnosti za preskuse in meritve za izenačevalnik dinamične ojačitve s spojitvenimi vlakni za uporabo v nadzorovanem okolju (DGTE). Izenačevalnik dinamične ojačitve se uporablja v optičnem ojačevalniku, ki deluje v pasu C in/ali L, za nadzorovanje izhodne moči ojačevalnika, da ostane nazivno ravna. Operativno območje valovne dolžine izenačevalnika dinamične ojačitve je širše ali enako 35 nm.

General Information

• Status: Published
• Publication Date: 07-Mar-2013
• Withdrawal Date: 08-Jan-2016
• ICS: 33.180.01 - Fibre optic systems in general
• ICS: 33.180.99 - Other fibre optic equipment
• Technical Committee: CLC/SR 86C - Fibre optic systems and active devices
• Drafting Committee: IEC/SC 86C - IEC_SC_86C
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 08-Mar-2013
• Completion Date: 08-Mar-2013
• Ref Project: SIST EN 62343-1-3:2013 - Dynamic modules - Part 1-3: Performance standards - Dynamic gain tilt equalizer (non-connectorized) (IEC 62343-1-3:2012)

Relations

• Replaces: EN 62343-1-3:2006 - Dynamic modules - Part 1-3: Performance standards - Dynamic gain tilt equalizer with pigtails for use in controlled environments (Category C)
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2013
1DGRPHãþD
SIST EN 62343-1-3:2007
'LQDPLþQLHOHPHQWLGHO6WDQGDUGLODVWQRVWL,]HQDþHYDOQLNGLQDPLþQH
RMDþLWYHVVSRMLWYHQLPLYODNQL]DXSRUDERYQDG]RURYDQHPRNROMX,(&

Dynamic modules - Part 1-3: Performance standards - Dynamic gain tilt equalizer (non-
connectorized) (IEC 62343-1-3:2012)
Dynamische Module - Teil 1-3: Betriebsverhalten - Dynamischer Equalizer mit
schräglagen Verstärkung (nicht mit Steckern versehen) (IEC 62343-1-3:2012)
Modules dynamiques - Partie 1-3: Normes de performance - Egaliseur dynamique de
basculement de gain (nonconnectorisé) (CEI 62343-1-3:2012)
Ta slovenski standard je istoveten z: EN 62343-1-3:2013
ICS:
33.180.30 2SWLþQLRMDþHYDOQLNL Optic amplifiers
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 62343-1-3
NORME EUROPÉENNE
March 2013
EUROPÄISCHE NORM
ICS 33.180.01; 33.180.99 Supersedes EN 62343-1-3:2006

English version
Dynamic modules -
Part 1-3: Performance standards -
Dynamic gain tilt equalizer (non-connectorized)
(IEC 62343-1-3:2012)
Modules dynamiques -  Dynamische Module -
Partie 1-3: Normes de performance - Teil 1-3: Betriebsverhalten -
Egaliseur dynamique de basculement de Dynamischer Equalizer mit schräglagen
gain (non-connectorisé) Verstärkung (nicht mit Steckern versehen)
(CEI 62343-1-3:2012) (IEC 62343-1-3:2012)

This European Standard was approved by CENELEC on 2013-01-09. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62343-1-3:2013 E
Foreword
The text of document 86C/1077/CDV, future edition 2 of IEC 62343-1-3, prepared by SC 86C, "Fibre optic
systems and active devices", of IEC TC 86, "Fibre optics" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN 62343-1-3:2013.
The following dates are fixed:
(dop) 2013-10-09
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2016-01-09
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 62343-1-3:2006.
3:2006:
a) a change in the title removing the environmental category;
b) the addition of Clause 4, Operating and storage conditions;
c) the inclusion of spectral bands in Clause 5, Test;
d) a definition of the wavelength range for test requirements in Clause 5, Test;
e) the removal of the environment tests from the test details and requirements.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 62343-1-3:2012 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61753-1 NOTE  Harmonized as EN 61753-1.

- 3 - EN 62343-1-3:2013
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 61300-2-14 - Fibre optic interconnecting devices and EN 61300-2-14 -
passive components - Basic test and
measurement procedures -
Part 2-14: Tests - High optical power

IEC 61300-3-2 - Fibre optic interconnecting devices and EN 61300-3-2 -
passive components - Basic test and
measurement procedures -
Part 3-2: Examinations and measurements -
Polarization dependent loss in a single-mode
fibre optic device
IEC 61300-3-6 - Fibre optic interconnecting devices and EN 61300-3-6 -
passive components - Basic test and
measurement procedures -
Part 3-6: Examinations and measurements -
Return loss
IEC 61300-3-7 - Fibre optic interconnecting devices and EN 61300-3-7 -
passive components - Basic test and
measurement procedures -
Part 3-7: Examinations and measurements -
Wavelength dependence of attenuation and
return loss of single mode components

IEC 61300-3-32 - Fibre optic interconnecting devices and EN 61300-3-32 -
passive components - Basic test and
measurement procedures -
Part 3-32: Examinations and measurements -
Polarisation mode dispersion measurement
for passive optical components

IEC 61300-3-38 - Fibre optic interconnecting devices and EN 61300-3-38 -
passive components - Basic test and
measurement procedures -
Part 3-38:Examinations and measurements -
Group delay, chromatic dispersion and phase
ripple
IEC 61753-021-2 - Fibre optic interconnecting devices and EN 61753-021-2 -
passive components performance standard -
Part 021-2: Grade C/3 single-mode fibre optic
connectors for category C - Controlled
environment
IEC 61753-022-2 - Fibre optic interconnecting devices and EN 61753-022-2 -
passive components - Performance standard -
Part 022-2: Fibre optic connectors terminated
on multimode fibre for category C - Controlled
environment
Publication Year Title EN/HD Year
IEC 62343-5-1 - Dynamic modules - Test methods - EN 62343-5-1 -
Part 5-1: Dynamic gain tilt equalizer -
Response time measurement
ITU-T - Optical interfaces for multichannel systems - -
Recommendation with optical amplifiers
G.692
IEC 62343-1-3 ®
Edition 2.0 2012-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Dynamic modules –
Part 1-3: Performance standards – Dynamic gain tilt equalizer (non-

connectorized)
Modules dynamiques –
Partie 1-3: Normes de performance – Egaliseur dynamique de basculement de

gain (non-connectorisé)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX L
ICS 33.180.01; 33.180.99 ISBN 978-2-83220-516-7

– 2 – 62343-1-3 © IEC:2012
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Operating and storage conditions . 7
4.1 Operating conditions . 7
4.2 Storage environmental conditions . 7
5 Test . 8
6 Test report . 8
7 Performance requirements . 8
7.1 Dimensions . 8
7.2 Sample size . 8
7.3 Test details and requirements . 8
Bibliography . 11

Table 1 – Operating conditions . 7
Table 2 – Storage environmental conditions . 7
Table 3 – Test details and requirements . 9

62343-1-3 © IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DYNAMIC MODULES –
Part 1-3: Performance standards –
Dynamic gain tilt equalizer (non-connectorized)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62343-1-3 has been prepared by subcommittee 86C: Fibre optic
systems and active devices, of IEC technical committee 86: Fibre optics.
This second edition cancels and replaces the first edition published in 2006. I
...