prEN IEC 62841-4-9:2023/prAA:2023
(Amendment)Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 4-9: Particular requirements for chain saws for tree service
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 4-9: Particular requirements for chain saws for tree service
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 4-9: Exigences particulières pour les scies à chaîne alimentées par batterie pour l’élagage des arbres
No scope available
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 4-9. del: Posebne zahteve za verižne žage za nego dreves - Dopolnilo AA
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2023
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 4-
9. del: Posebne zahteve za verižne žage za nego dreves - Dopolnilo AA
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 4-9: Particular requirements for chain saws for tree service
Ta slovenski standard je istoveten z: prEN IEC 62841-4-9:2023/prAA:2023
ICS:
25.140.20 Električna orodja Electric tools
65.060.70 Vrtnarska oprema Horticultural equipment
oSIST prEN IEC 62841-4- en
9:2023/oprAA:2023
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD DRAFT
prEN IEC 62841-4-9
NORME EUROPÉENNE
EUROPÄISCHE NORM
prAA
September 2023
ICS -
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 4-9: Particular
requirements for chain saws for tree service
To be completed To be completed
This draft amendment prAA, if approved, will modify the European Standard prEN IEC 62841-4-9; it is submitted to CENELEC members for
enquiry.
Deadline for CENELEC: 2023-11-24.
It has been drawn up by CLC/TC 116.
If this draft becomes an amendment, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
This draft amendment was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 78418 Ref. No. prEN IEC 62841-4-9:2023/prAA:2023 E
1 Contents Page
2 European foreword . 3
3 1 Modification to Clause 2, “Normative references” . 5
4 2 Modifications to Clause 8, “Marking and instructions” . 5
5 3 Modification to Annex I, “Measurement of noise and vibration emissions” . 5
6 4 Modifications to Annex K, “Battery tools and battery packs” . 5
7 5 Addition of Annex ZA, “Normative references to international publications with their
8 corresponding European publications” . 6
9 6 Addition of Annex ZZ, “Relationship between this European Standard and the essential
10 requirements of Directive 2006/42/EC aimed to be covered” . 8
11 European foreword
12 This document (prEN IEC 62841-4-9:2023/prAA:2023) has been prepared by CLC/TC 116 “Safety and
13 environmental aspects of motor-operated electric tools”.
14 This document is currently submitted to the Enquiry.
15 The following dates are proposed:
• latest date by which the existence of this (doa) dor + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dor + 48 months
conflicting with this document have to be (to be confirmed or
withdrawn modified when voting)
16 This document modifies by common modifications prEN IEC 62841-4-9:2023, which consists of the text of
17 116/xxx/CDV (future IEC 62841-4-9, Ed. 1) prepared by IEC/TC 116 “Safety of motor-operated electric tools”.
18 If approved, this draft amendment will be published as EN IEC 62841-4-9:202x/A11:202x.
19 This series is divided into four parts.
20 Part 1: General requirements which are common to most hand-held electric motor operated tools (for the
21 purpose of this document referred to simply as tools) which could come within the scope of this document;
22 Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the requirements
23 given in Part 1 to account for the particular hazards and characteristics of these specific tools.
24 Part 4-9 is used in conjunction with EN 62841-1:2015 and its amendments.
25 Part 4-9 supplements or modifies the corresponding clauses in EN 62841-1:2015 and its amendments, so as to
26 convert it into the European Standard: Particular requirements for battery-powered chain saws for tree service.
27 Where a particular subclause of Part 1 is not mentioned in the Part 4-9, that subclause applies. When this
28 document states “addition”, “modification” or “replacement”, the relevant text in Part 1 is to be adapted
29 accordingly.
30 The following print types are used:
31 — requirements; in roman type;
32 — test specifications: in italic type;
33 — notes: in smaller roman type.
34 The terms defined in Clause 3 are printed in bold typeface.
35 Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting from 101.
36 Clauses, subclauses, notes, tables, figures and annexes which are additional to those in IEC 62841-4-9:202x
37 are prefixed “Z”.
38 This document follows the overall requirements of EN ISO 12100.
39 This document has been prepared under a standardization request addressed to CENELEC by the European
40 Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
41 Member States.
42 For the relationship with EU Legislation, see informative Annex ZZ, which is an integral part of this document.
43 Compliance with the clauses of Part 1 together with Part 4-9 provides one means of conforming with the
44 essential health and safety requirements of the Directive concerned.
45 1 Modification to Clause 2, “Normative references”
46 Add the following normative reference:
47 EN ISO 7010:2020, Graphical symbols - Safety colours and safety signs - Registered safety signs (ISO
48 7010:2019, Corrected version 2020-06)
49 2 Modifications to Clause 8, “Marking and instructions”
50 Replace the text of Clause 8 with the following:
51 “EN 62841-1:2015, Clause 8 is applicable, except as follows.
52 8.14.2 Za) Replacement:
53 Emissions:
54 1) The noise emission, measured in accordance with Clause I.2, as follows:
55 — A-weighted emission sound pressure level L and its uncertainty K , where L exceeds 70 dB(A).
pA pA pA
56 Where L does not exceed 70 dB(A), this fact shall be indicated;
pA
57 — A-weighted guaranteed sound power level L .
WA
58 2) Recommendation for the operator to wear hearing protection.
59 3) The following information:
60 — that the declared noise emission value(s) have been measured in accordance with a standard test
61 method and may be used for comparing one machine with another;
62 — that the declared noise emission value(s) may also be used in a preliminary assessment of exposure.
63 4) A warning:
64 — that the noise emissions during actual use of the machine can differ from the declared value depending
65 on the ways in which the machine is used especially what kind of workpiece is processed; and
66 — of the need to identify safety measures to protect the operator that are based on an estimation of
67 exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the
68 times when the machine is switched off and when it is running idle in addition to the operating time).”
69 3 Modification to Annex I, “Measurement of noise and vibration emissions”
70 Replace the title of Annex I with the following:
71 “Annex I
72 (normative)
74 Measurement of noise and vibration emissions”
75 and delete the NOTE.
76 4 Modifications to Annex K, “Battery tools and battery packs”
77 In K.8.2, replace NOTE 301 with the following normative text:
78 “In addition, chain saws shall be marked, using text or a product safety label, with the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.