Multi-element metallic cables used in analogue and digital communication and control - Part 6-2: Sectional specification for unscreened cables characterised up to 250 MHz - Work area and patch cord cables

EN 50288-6-2 is a sectional specification for unscreened cables, characterised from 1 MHz up to 250 MHz, to be used as work area cables to connect a telecommunications outlet to the terminal equipment and for patch cord cables to establish connections on a patch panel as defined in EN 50173. Work area and data centres cables may also be used as patch cord cables in any distributor of a generic building wiring system to interconnect with equipment or to cross-connect between cabling systems. This sectional specification contains the electrical, mechanical, transmission and environmental performance characteristics of the cables, when tested in accordance with the referenced test methods. This sectional specification is to be read in conjunction with EN 50288-1, which contains the essential provisions for its application. The cables covered in this sectional specification are intended to operate with voltages and currents normally encountered in communication systems. These cables are not intended to be used in conjunction with low impedance sources, for example, the electric power supplies of public utility mains.

Mehradrige metallische Daten- und Kontrollkabel für analoge und digitale Übertragung - Teil 6-2: Rahmenspezifikation für ungeschirmte Kabel bis 250 MHz - Geräteanschlusskabel und Schaltkabel

Câbles métalliques à éléments multiples utilisés pour les transmissions et les commandes analogiques et numériques - Partie 6-2: Spécification intermédiaire pour les câbles non écrantés pour applications jusqu'à 250 MHz - Câbles de zone de travail et de brassage

L’EN 50288-6-2 est une spécification intermédiaire relative aux câbles non écrantés caractérisés de 1 MHz jusqu'à 250 MHz, destinés à utilisés comme câbles de zone de travail pour relier une prise de télécommunication à un équipement terminal et comme câbles pour cordons de brassage pour établir les connexions sur les panneaux de brassage comme défini dans l’EN 50173. Les câbles de zone de travail et de centres de traitement de données peuvent également être utilisés comme câbles pour cordons de brassage dans tout répartiteur d'un système générique de câblage de bâtiment pour l'interconnexion d'équipements ou le brassage entre systèmes de câblage. La présente spécification intermédiaire contient les caractéristiques de performances électriques, mécaniques, de transmission et d'environnement des câbles, lorsqu’ils sont soumis aux essais selon les méthodes d'essai référencées. La présente spécification intermédiaire doit être utilisée conjointement avec l’EN 50288-1, qui contient les dispositions essentielles pour son application. Les câbles couverts par la présente spécification intermédiaire sont destinés à fonctionner avec des tensions et des courants rencontrés normalement dans les systèmes de communication. Ces câbles ne sont pas destinés à être utilisés conjointement avec des sources à faible impédance, par exemple, les alimentations électriques du réseau public.

Večelementni kovinski kabli za analogne in digitalne komunikacije in krmiljenje - 6-2. del: Področna specifikacija za nezaslonjene kable z lastnostmi do 250 MHz - Kabli za delovna območja in povezovalne vrvice

Standard EN 50288-6-2 je področna specifikacija za nezaslonjene kable, ki se lahko uporabljajo za pasovne širine od 1 MHz do 250 MHz kot kabli na delovnem območju za povezavo telekomunikacijske vtičnice s terminalsko opremo, ter za povezovalne vrvice za vzpostavljanje povezav na povezovalni plošči, kot je določeno v EN 50173. Kabli delovnega območja in podatkovnih centrov se lahko uporabljajo tudi kot povezovalne vrvice v katerem koli razdelilniku generičnega stavbnega sistema ožičenja za povezavo z opremo ali navzkrižno povezavo med kabelskimi sistemi. Ta področna specifikacija vsebuje električne, mehanske, prenosne in okoljske karakteristike delovanja kablov pri preskušanju v skladu z navedenimi preskusnimi metodami. Ta področna specifikacija se uporablja skupaj s standardom EN 50288-1, ki vsebuje bistvene določbe za njeno uporabo. Kabli, zajeti v tej področni specifikaciji, so namenjeni za delovanje pri napetostih in tokovih, ki so običajni v komunikacijskih sistemih. Ti kabli niso namenjeni za uporabo z viri z nizko impedanco, na primer z električnim napajanjem javnih omrežij.

General Information

Status
Published
Publication Date
23-May-2013
Current Stage
6060 - Document made available
Due Date
24-May-2013
Completion Date
24-May-2013

RELATIONS

Buy Standard

Standard
EN 50288-6-2:2013
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 50288-6-2:2013
01-oktober-2013

9HþHOHPHQWQLNRYLQVNLNDEOL]DDQDORJQHLQGLJLWDOQHNRPXQLNDFLMHLQNUPLOMHQMH

GHO3RGURþQDVSHFLILNDFLMD]DQH]DVORQMHQHNDEOH]ODVWQRVWPLGR0+]
.DEOL]DGHORYQDREPRþMDLQSRYH]RYDOQHYUYLFH

Multi-element metallic cables used in analogue and digital communication and control --

Part 6-2: Sectional specification for unscreened cables characterised up to 250 MHz -

Work area and patch cord cables

Mehradrige metallische Daten- und Kontrollkabel für analoge und digitale Übertragung --

Teil 6-2: Rahmenspezifikation für ungeschirmte Kabel bis 250 MHz -
Geräteanschlusskabel und Schaltkabel
Câbles métalliques à éléments multiples utilisés pour les transmissions et les

commandes analogiques et numériques -- Partie 6-2: Spécification intermédiaire pour les

câbles non blindés pour applications jusqu'à 250 MHz - Câbles de zone de travail et de

brassage
Ta slovenski standard je istoveten z: EN 50288-6-2:2013
ICS:
33.120.20 äLFHLQVLPHWULþQLNDEOL Wires and symmetrical
cables
SIST EN 50288-6-2:2013 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 50288-6-2:2013
---------------------- Page: 2 ----------------------
SIST EN 50288-6-2:2013
EUROPEAN STANDARD
EN 50288-6-2
NORME EUROPÉENNE
May 2013
EUROPÄISCHE NORM
ICS 33.120.20 Supersedes EN 50288-6-2:2003
English version
Multi-element metallic cables used in analogue and digital communication
and control -
Part 6-2: Sectional specification for unscreened cables characterised up
to 250 MHz -
Work area and patch cord cables
Câbles métalliques à éléments multiples Mehradrige metallische Daten- und
utilisés pour les transmissions et les Kontrollkabel für analoge und digitale
commandes analogiques et numériques - Übertragung -
Partie 6-2: Spécification intermédiaire Teil 6-2: Rahmenspezifikation für
pour les câbles non blindés pour ungeschirmte Kabel bis 250 MHz -
applications jusqu'à 250 MHz - Geräteanschlusskabel und Schaltkabel
Câbles de zone de travail et de brassage

This European Standard was approved by CENELEC on 2013-03-18. CENELEC members are bound to comply

with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on

application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CENELEC member into its own language and notified

to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,

the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,

Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,

Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 50288-6-2:2013 E
---------------------- Page: 3 ----------------------
SIST EN 50288-6-2:2013
EN 50288-6-2:2013 - 2 -
Contents
Page

Foreword ................................................................................................................................ 3

1 Scope .............................................................................................................................. 4

2 Normative references ....................................................................................................... 4

3 Terms, definitions, symbols and abbreviations .................................................................. 4

3.1 Terms and definitions .............................................................................................. 4

3.2 Symbols and abbreviations ...................................................................................... 5

4 Cable construction ............................................................................................................ 5

4.1 Conductor ............................................................................................................... 5

4.2 Insulation ................................................................................................................ 5

4.3 Cabling elements .................................................................................................... 5

4.4 Identification of cabling elements ............................................................................. 5

4.5 Screening of cabling elements ................................................................................. 5

4.6 Cable make-up ........................................................................................................ 5

4.7 Filling compound ..................................................................................................... 5

4.8 Interstitial fillers ....................................................................................................... 5

4.9 Screening of the cable core ..................................................................................... 5

4.10 Moisture barriers ..................................................................................................... 6

4.11 Wrapping layers ...................................................................................................... 6

4.12 Sheath .................................................................................................................... 6

5 Tests and requirements for completed cables ................................................................... 6

5.1 Electrical tests ......................................................................................................... 6

5.2 Mechanical tests ..................................................................................................... 9

5.3 Environmental tests ............................................................................................... 10

5.4 Fire performance tests .......................................................................................... 10

Annex A (Informative) Maximum voltage, current and temperature rating for cables

used for POE applications .............................................................................................. 11

Annex B (Informative) Blank Detail Specification .................................................................. 12

---------------------- Page: 4 ----------------------
SIST EN 50288-6-2:2013
- 3 - EN 50288-6-2:2013
Foreword

This document EN 50288-6-2:2013 has been prepared by CLC/SC 46XC "Multicore, Multipair and

Quad Data communication cables," of CLC/TC 46X, "Communication cables".
The following dates are fixed:
• latest date by which this document has
(dop) 2014-03-18
to be implemented at national level by
publication of an identical national standard or
by endorsement
• latest date by which the national standards
(dow) 2016-03-18
conflicting with this document have to
be withdrawn
This document supersedes EN 50288-6-2:2003.

EN 50288-6-2:2013 includes the following significant technical changes with respect to EN 50288-6-

2:2003:
- the addition of the Blank Detail Specification Annex;
- a number minor corrections and updating of references;
- the re-classification of ‘ELFEXT’ to ‘ACR-F’.
This Part 6-2 is to be read in conjunction to EN 50288-1.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such

patent rights.

This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment

Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC)
---------------------- Page: 5 ----------------------
SIST EN 50288-6-2:2013
EN 50288-6-2:2013 - 4 -
1 Scope

EN 50288-6-2 is a sectional specification for unscreened cables, characterised from 1 MHz up to

250 MHz, to be used as work area cables to connect a telecommunications outlet to the terminal

equipment and for patch cord cables to establish connections on a patch panel as defined in

EN 50173.

Work area and data centres cables may also be used as patch cord cables in any distributor of a

generic building wiring system to interconnect with equipment or to cross-connect between cabling

systems.

This sectional specification contains the electrical, mechanical, transmission and environmental

performance characteristics of the cables, when tested in accordance with the referenced test

methods.

This sectional specification is to be read in conjunction with EN 50288-1, which contains the essential

provisions for its application.

The cables covered in this sectional specification are intended to operate with voltages and currents

normally encountered in communication systems. These cables are not intended to be used in

conjunction with low impedance sources, for example, the electric power supplies of public utility

mains.
2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and

are indispensable for its application. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments)

applies.
EN 50173 Series Information technology — Generic cabling systems
EN 50288-1 Multi-element metallic cables used in analogue and digital
communication and control — Part 1: Generic specification
EN 50289 Series Communication cables — Specifications for test methods
EN 50290 Series Communication cables

EN 60811 Series Electric and optical fibre cables — Test methods for non-metallic

materials (IEC 60811 series)
IEC 60189-2 Low-frequency cables and wires with PVC insulation and PVC
sheath — Part 2: Cables in pairs, triples, quads and quintuples
for inside installations
3 Terms, definitions, symbols and abbreviations
3.1 Terms and definitions

For the purposes of this document the terms and definitions given in EN 50288-1 apply.

---------------------- Page: 6 ----------------------
SIST EN 50288-6-2:2013
- 5 - EN 50288-6-2:2013
3.2 Symbols and abbreviations
For the purposes of this document, the following abbreviations apply.
EX Exogenous (derived or originating externally)
POE Power Over Ethernet
4 Cable construction
4.1 Conductor
The conductor shall be solid or stranded copper and meet the requirements of
EN 50288-1, 4.1

The stranded conductor shall consist of seven wires each with a nominal diameter of ≥ 0,10 mm to

≤ 0,21 mm.
The conductor shall be plain or metal coated.
The solid conductor nominal diameter shall be ≥ 0,4 mm to ≤ 0,8 mm.
NOTE Constructions with ‘copper clad’ conductors do not meet the requirements
4.2 Insulation

The insulation shall be of a suitable material according to the relevant part of EN 50290-2.

4.3 Cabling elements
The cable element shall be a pair or a quad.
4.4 Identification of cabling elements

Unless otherwise specified, the colour coding for identification is given in IEC 60189-2. The colours

shall meet the requirements of EN 50288-1, 4.4
4.5 Screening of cabling elements
Not applicable.
4.6 Cable make-up

The cable elements shall be laid up in concentric layer(s) or units to form the cable core.

4.7 Filling compound
Not applicable.
4.8 Interstitial fillers
Where fillers are used they shall meet the requirements of EN 50288-1, 4.8
4.9 Screening of the cable core
Not applicable.
---------------------- Page: 7 ----------------------
SIST EN 50288-6-2:2013
EN 50288-6-2:2013 - 6 -
4.10 Moisture barriers
Not applicable.
4.11 Wrapping layers

Where wrapping layers are used they shall be in accordance with EN 50288-1, 4.11.

4.12 Sheath

The sheath shall be of a suitable material according to the relevant part of EN 50290-2.

5 Tests and requirements for completed cables

The following tables give the tests to be applied, together with the respective limits, in order to

demonstrate compliance with this specification.
5.1 Electrical tests
5.1.1 Low-frequency and d.c. electrical measurements
Table 1 - Low-frequency and d.c. electrical measurements
EN 50288-1 Parameter Requirement
sub-clause
5.1.1.1 Conductor loop resistance (D1)≤ 28 Ω/100 m
(D2)≤ 34 Ω/100 m
5.1.1.2 Conductor resistance unbalance
≤ 2,0 %
5.1.1.3 Dielectric strength 1,0 kV d.c. or 0,7 kV a.c. for 1 min
conductor/conductor or
2,5 kV d.c. or 1,7 kV a.c. for 2 s
5.1.1.4 Insulation resistance
≥ 5 000 MΩ km when tested in accordance with EN
50289-1-4
5.1.1.5 Mutual capacitance No requirement specified
5.1.1.6 Capacitance unbalance to earth
≤ 1 200 pF/km
---------------------- Page: 8 ----------------------
SIST EN 50288-6-2:2013
- 7 - EN 50288-6-2:2013
5.1.2 High-frequency electrical and transmission measurements
Table 2 - High-frequency electrical and transmission requirements
Parameter Requirement
EN 50288-1
sub-clause
5.1.2.1 Velocity of propagation
Phase delay ≤ 534+36/√f ns/100 m
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.