Multi-element metallic cables used in analogue and digital communication and control - Part 10-2: Sectional specification for screened cables characterized from 1 MHz up to 500 MHz for work area, patch cord and data centre applications

EN 50288-10-1 is a sectional specification for screened cables, characterised from 1 MHz up to 500 MHz, to be as work area cables to connect a telecommunications outlet to the terminal equipment and for patch cord cables to establish connections on a patch panel as defined in EN 50173. Work area and data centres cables may also be used as patch cord cables in any distributor of a generic building wiring system to interconnect with equipment or to cross-connect between cabling systems. This sectional specification contains the electrical, mechanical, transmission and environmental performance characteristics and requirements of the cables when tested in accordance with the referenced test methods. This sectional specification is to be read in conjunction with EN 50288-1, which contains the essential provisions for its application. The cables covered in this sectional specification are intended to operate with voltages and currents normally encountered in communications systems. These cables are not intended to be used in conjunction with low impedance sources, for example the electrical power supplies of public utility mains.

Mehradrige metallische Daten- und Kontrollkabel für analoge und digitale Kommunikation - Teil 10-2: Rahmenspezifikation für geschirmte Kabel von 1 MHz bis 500 MHz für Geräteanschlusskabel, Schaltkabel und Anwendungen für Rechenzentren

EN 50288-10-2 ist eine Rahmenspezifikation für geschirmte Kabel von 1 MHz bis 500 MHz zur Verwendung als Geräteanschlusskabel für den Anschluss von Endgeräten an informationstechnische Anschlüsse und als Schaltkabel zur Herstellung von Verbindungen an Rangierfeldern nach EN 50173. Geräteanschlusskabel und Kabel für Rechenzentren dürfen auch als Schaltkabel in jedem Verteiler einer anwendungsneutralen Kommuni-kationskabelanlage zur Verbindung mit Geräten oder zur Verbindung zwischen Kommunikationskabelanlagen verwendet werden. Diese Rahmenspezifikation beschreibt die elektrischen, mechanischen, übertragungstechnischen und umge-bungsrelevanten Eigenschaften und Anforderungen für Kabel, die nach den angegebenen Referenzprüf-verfahren geprüft werden. Diese Rahmenspezifikation ist zusammen mit EN 50288-1 anzuwenden, die die grundlegenden Anwendungs-bestimmungen enthält. Die in dieser Rahmenspezifikation beschriebenen Kabel sind für den Betrieb mit Spannungen und Strömen vorgesehen, die üblicherweise in Kommunikationssystemen vorkommen. Diese Kabel sind nicht für die Verwendung in Verbindung mit niederohmigen Quellen vorgesehen, wie zum Beispiel Verteilungsnetzen zur elektrischen Energieversorgung.

Câbles métalliques à éléments multiples utilisés pour les transmissions et les commandes analogiques et numériques - Partie 10-2: Spécification intermédiaire pour les câbles écrantés caractérisés de 1 MHz à 500 MHz - Câbles horizontaux et câbles verticaux de bâtiment

La présente spécification intermédiaire s'applique aux câbles écrantés caractérisés de 1 MHz à 500 MHz destinés à être utilisés pour la construction de cordons dans les câblages spécifiés dans la série de normes EN 50173. Les normes de câblage spécifiques aux locaux de la série EN 50173 font référence aux exigences D1 de la présente spécification pour les câbles utilisés dans les cordons relevant des "mises en œuvre de référence" de ces normes. Les exigences alternatives D2 de la présente spécification peuvent être utilisées pour la production de cordons pour d’autres mises en œuvre et applications, y compris le raccordement direct de matériels dans les centres de traitement de données. La présente spécification intermédiaire contient les caractéristiques et les exigences applicables pour les performances électriques, mécaniques, de transmission et d’environnement relatives aux câbles soumis aux essais selon les méthodes d’essai référencées. La présente spécification intermédiaire doit être utilisée conjointement avec l’EN 50288-1, qui contient les dispositions essentielles pour son application. Les câbles couverts par la présente spécification intermédiaire sont destinés à fonctionner avec des tensions et des courants rencontrés normalement dans les systèmes de communication. Ces câbles ne sont pas destinés à être utilisés conjointement avec des sources de faible impédance, par exemple, les alimentations électriques du réseau public.

Večelementni kovinski kabli za analogne in digitalne komunikacije in krmiljenje - 10-2. del: Področna specifikacija za zaslonjene kable z lastnostmi od 1 MHz do 500 MHz - Vodoravni (etažni) in stavbni hrbtenični (medetažni) kabli

Standard EN 50288-10-1 je področna specifikacija za zaslonjene kable, ki se lahko uporabljajo za pasovne širine od 1 MHz do 500 MHz kot kabli na delovnem območju za povezavo telekomunikacijske vtičnice s terminalsko opremo, ter za povezovalne vrvice za vzpostavljanje povezav na povezovalni plošči, kot je določeno v standardu EN 50173. Kabli delovnega območja in podatkovnih centrov se lahko uporabljajo tudi kot povezovalne vrvice v katerem koli razdelilniku generičnega stavbnega sistema ožičenja za povezavo z opremo ali navzkrižno povezavo med kabelskimi sistemi.
Ta področna specifikacija vsebuje električne, mehanske, prenosne in okoljske karakteristike delovanja ter zahteve za kable pri preskušanju v skladu z navedenimi preskusnimi metodami.
Ta področna specifikacija se uporablja skupaj s standardom EN 50288-1, ki vsebuje bistvene določbe za njeno uporabo.
Kabli, zajeti v tej področni specifikaciji, so namenjeni za delovanje pri napetostih in tokovih, ki so običajni v komunikacijskih sistemih. Ti kabli niso namenjeni za uporabo z viri z nizko impedanco, na primer z električnim napajanjem javnih omrežij.

General Information

Status
Published
Publication Date
03-Sep-2015
Current Stage
6060 - Document made available
Due Date
04-Sep-2015
Completion Date
04-Sep-2015

Buy Standard

Standard
EN 50288-10-2:2016
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 50288-10-2:2016
01-februar-2016

9HþHOHPHQWQLNRYLQVNLNDEOL]DDQDORJQHLQGLJLWDOQHNRPXQLNDFLMHLQNUPLOMHQMH

GHO3RGURþQDVSHFLILNDFLMD]D]DVORQMHQHNDEOH]ODVWQRVWPLRG0+]GR

0+]9RGRUDYQL HWDåQL LQVWDYEQLKUEWHQLþQL PHGHWDåQL NDEOL

Multi-element metallic cables used in analogue and digital communication and control -

Part 10-2: Sectional specification for screened cables characterized from 1 MHz up to

500 MHz - Horizontal and building backbone cables

Mehradrige metallische Daten- und Kontrollkabel für analoge und digitale Übertragung --

Teil 10-2: Rahmenspezifikation für geschirmte Kabel von 1 MHz bis 500 MHz - Kabel für

den Horizontal- und Steigbereich
Câbles métalliques à éléments multiples utilisés pour les transmissions et les

commandes analogiques et numériques -- Partie 10-2: Spécification intermédiaire pour

les câbles écrantés caractérisés de 1 MHz à 500 MHz - Câbles horizontaux et câbles

verticaux de bâtiment
Ta slovenski standard je istoveten z: EN 50288-10-2:2015
ICS:
33.120.20 äLFHLQVLPHWULþQLNDEOL Wires and symmetrical
cables
SIST EN 50288-10-2:2016 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 50288-10-2:2016
---------------------- Page: 2 ----------------------
SIST EN 50288-10-2:2016
EUROPEAN STANDARD EN 50288-10-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2015
ICS 33.120.10; 33.120.20
English Version
Multi-element metallic cables used in analogue and digital
communication and control - Part 10-2: Sectional specification
for screened cables characterized from 1 MHz up to 500 MHz for
work area, patch cord and data centre applications

Câbles métalliques à éléments multiples utilisés pour les Mehradrige metallische Daten- und Kontrollkabel für

transmissions et les commandes analogiques et
analoge und digitale Kommunikation - Teil 10-2:

numériques - Partie 10-2: Spécification intermédiaire pour Rahmenspezifikation für geschirmte Kabel von 1 MHz bis

les câbles écrantés caractérisés de 1 MHz à 500 MHz - 500 MHz für Geräteanschlusskabel, Schaltkabel und

Câbles horizontaux et câbles verticaux de bâtiment Anwendungen für Rechenzentren

This European Standard was approved by CENELEC on 2015-08-03. CENELEC members are bound to comply with the CEN/CENELEC

Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the

same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN 50288-10-2:2015 E
---------------------- Page: 3 ----------------------
SIST EN 50288-10-2:2016
EN 50288-10-2:2015
Contents Page

European foreword ........................................................................................................................................... 3

1 Scope .......................................................................................................................................................... 4

2 Normative references ................................................................................................................................ 4

3 Terms, definitions, symbols and abbreviations ..................................................................................... 5

3.1 Terms and definitions ........................................................................................................................ 5

3.2 Symbols and abbreviations ............................................................................................................... 5

4 Cable construction .................................................................................................................................... 5

4.1 Conductor .......................................................................................................................................... 5

4.2 Insulation ........................................................................................................................................... 5

4.3 Cabling elements ............................................................................................................................... 5

4.4 Identification of cabling elements ...................................................................................................... 5

4.5 Screening of cabling elements .......................................................................................................... 6

4.6 Cable make-up .................................................................................................................................. 6

4.7 Filling compound ............................................................................................................................... 6

4.8 Interstitial fillers .................................................................................................................................. 6

4.9 Screening of the cable core ............................................................................................................... 6

4.10 Moisture barriers ............................................................................................................................... 6

4.11 Wrapping layers ................................................................................................................................ 6

4.12 Sheath ............................................................................................................................................... 6

5 Test methods and requirements for completed cables ......................................................................... 7

5.1 General .............................................................................................................................................. 7

5.2 Electrical tests ................................................................................................................................... 7

5.3 Mechanical tests .............................................................................................................................. 11

5.4 Environmental tests ......................................................................................................................... 12

5.5 Fire performance tests .................................................................................................................... 12

Annex A (informative) Maximum voltage, current and temperature rating for cables used for

POE applications ..................................................................................................................................... 13

Annex B (informative) Blank Detail Specification ...................................................................................... 14

B.1 General ............................................................................................................................................ 14

B.2 Document details ............................................................................................................................. 14

B.3 Generic specification EN 50288-1 ................................................................................................... 15

Tables

Table 1 – Low-frequency and d.c. electrical measurements ..............................................................................7

Table 2 – High-frequency electrical and transmission requirements ..................................................................8

Table 3 – Mechanical test requirements ...........................................................................................................11

Table 4 – Environmental test requirements ......................................................................................................12

Table A.1 – Maximum recommended voltage, current, current density and conductor temperature for

cables when used for POE applications ....................................................................................................13

Table B.1 – Blank detail specification for symmetrical pair/quad cables for digital communications ...............16

---------------------- Page: 4 ----------------------
SIST EN 50288-10-2:2016
EN 50288-10-2:2015
European foreword

This document (EN 50288-10-2:2015) has been prepared by CLC/SC 46XC "Multicore, multipair and quad

data communication cables," of CLC/TC 46X, "Communication cables".
The following dates are fixed:
(dop) 2016-08-03
• latest date by which this document has to be
implemented at national level by publication of
an identical national standard or by
endorsement
(dow) 2018-08-03
• latest date by which the national standards
conflicting with this document have to
be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.

This Part 10-2 is to be read in conjunction to EN 50288-1.

This document has been prepared under a mandate given to CENELEC by the European Commission and

the European Free Trade Association.

This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed for

Use within Certain Voltage Limits (LVD - 2006/95/EC).
---------------------- Page: 5 ----------------------
SIST EN 50288-10-2:2016
EN 50288-10-2:2015
1 Scope

This sectional specification covers screened cables, characterised from 1 MHz up to 500 MHz, to be used to

construct cords for use in cabling specified in the EN 50173 series of standards.

The premises-specific cabling standards of the EN 50173 series reference the D1 requirements of this

specification for the cable used within cords of the “reference implementations” of those standards. The

alternative D2 requirements of this specification may be used to produce cords for other implementations and

applications including the direct connection of equipment in data centres.

This sectional specification contains the electrical, mechanical, transmission and environmental performance

characteristics and requirements of the cables when tested in accordance with the referenced test methods.

This sectional specification is to be read in conjunction with EN 50288-1, which contains the essential

provisions for its application.

The cables covered in this sectional specification are intended to operate with voltages and currents normally

encountered in communications systems. These cables are not intended to be used in conjunction with low

impedance sources, for example the electrical power supplies of public utility mains.

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited applies. For undated references,

the latest edition of the referenced document (including any amendments) applies.

EN 50288-1:2013, Multi-element metallic cables used in analogue and digital communication and control –

Part 1: Generic specification

EN 50289-3-2, Communication cables – Specifications for test methods – Part 3-2: Mechanical test

methods – Tensile strength and elongation for conductor

EN 50289-3-4, Communication cables – Specifications for test methods – Part 3-4: Mechanical test

methods – Tensile strength, elongation and shrinkage of insulation and sheath

EN 50289-3-5, Communication cables – Specifications for test methods – Part 3-5: Mechanical test

methods – Crush resistance of the cable

EN 50289-3-6, Communication cables – Specifications for test methods – Part 3-6: Mechanical test

methods – Impact resistance of the cable

EN 50289-3-8, Communication cables – Specifications for test methods – Part 3-8: Mechanical test

methods – Abrasion resistance of cable sheath markings

EN 50289-3-9:2001, Communication cables – Specifications for test methods – Part 3-9: Mechanical test

methods – Bending tests

EN 50289-3-16, Communication cables – Specifications for test methods – Part 3-16: Mechanical test

methods – Cable tensile performance

EN 50289-4-6, Communication cables – Specifications for test methods – Part 4-6: Environmental test

methods – Temperature cycling

EN 50290-2 series, Communication cables – Part 2: Common design rules and construction

---------------------- Page: 6 ----------------------
SIST EN 50288-10-2:2016
EN 50288-10-2:2015

EN 60708, Low-frequency cables with polyolefin insulation and moisture barrier polyolefin sheath (IEC 60708)

IEC 60189-2, Low-frequency cables and wires with PVC insulation and PVC sheath – Part 2: Cables in pairs,

triples, quads and quintuples for inside installations
3 Terms, definitions, symbols and abbreviations
3.1 Terms and definitions

For the purposes of this document, the terms and definitions given in EN 50288-1 and the following apply.

3.1.1
screening of cable

a cable is considered screened when the cable core is covered by a continuous conductive layer forming a

part of the shielding and bonding system of the cabling system.

Note 1 to entry: DC continuity has to be given and minimum shielding requirements have to be met.

3.2 Symbols and abbreviations
For the purposes of this document, the following abbreviations apply.
EX Exogenous (derived or originating externally)
POE Power Over Ethernet
4 Cable construction
4.1 Conductor

The conductor shall be solid or stranded annealed copper and comply with the requirements of

EN 50288-1:2013, 4.1
The solid conductor nominal diameter shall be ≥ 0,40 mm and ≤ 0,80 mm.

The stranded conductor shall consist of seven wires each with a nominal diameter of ≥ 0,10 mm to

≤ 0,21 mm.
NOTE Constructions with ‘copper clad’ conductors do not meet the requirements.
4.2 Insulation

The insulation shall be of a suitable material in accordance with the appropriate part of the EN 50290-2

series.
4.3 Cabling elements
The cable element shall be a pair or quad.
4.4 Identification of cabling elements

Unless otherwise specified, the colour coding for identification shall be as specified in IEC 60189-2 or

EN 60708, as appropriate. The colours shall comply with the requirements given in EN 50288-1:2013, 4.4

---------------------- Page: 7 ----------------------
SIST EN 50288-10-2:2016
EN 50288-10-2:2015
4.5 Screening of cabling elements

Screening of the cabling elements shall be applied in accordance with EN 50288-1:2013, 4.5. When a braid is

used the minimum braid coverage (for mechanical purposes) shall be 60%. When a foil and braid are used

the minimum braid coverage (for mechanical purposes) shall be 30% coverage as defined in EN 50290-2-1

4.6 Cable make-up

The cable elements shall be laid up in concentric layer(s) or units to form the cable core.

4.7 Filling compound
Not applicable.
4.8 Interstitial fillers
Where fillers are used they shall meet the requirements of EN 50288-1:2013, 4.8
4.9 Screening of the cable core

The screening of the cable core shall be applied in accordance with EN 50288-1:2013, 4.9. When a braid is

used the minimum braid coverage (for mechanical purposes) shall be 60%. When a foil and braid are used,

and/or where a foil is used over each cabling element/the core, the minimum braid coverage (for mechanical

purposes) shall be 30% as defined in EN 50290-2-1
4.10 Moisture barriers
Not applicable.
4.11 Wrapping layers

Where wrapping layers are used they shall be in accordance with EN 50288-1:2013, 4.11

4.12 Sheath

The sheath shall be of a suitable material in accordance with the appropriate part of the EN 50290-2 series.

---------------------- Page: 8 ----------------------
SIST EN 50288-10-2:2016
EN 50288-10-2:2015
5 Test methods and requirements for completed cables
5.1 General

The following tables specify the tests that shall be applied to the completed cable, together with the

requirements to demonstrate compliance with this sectional specification.
5.2 Electrical tests
5.2.1 Low-frequency and DC electrical measurements
Table 1 – Low-frequency and DC electrical measurements
EN 50288-1:2013 Parameter Requirement
Sub-clause
5.1.1.1 Conductor loop resistance
(D1) ≤ 28,0 Ω/100 m
(D2) ≤ 34,0 Ω/100 m
5.1.1.2 Conductor resistance
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.