iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61234-2:1998

(Main)

Electrical insulating materials - Methods of test for the hydrolytic stability - Part 2: Moulded thermosets

Electrical insulating materials - Methods of test for the hydrolytic stability - Part 2: Moulded thermosets

Describes the test method for determination of hydrolytic stability of moulded thermosets made of room temperature or oven-curing reaction resins when subjected to simultaneous influence of water and high temperature. With this test method, irreversible change of mechanical and electrical properties is measured, but no mechanical stress is imposed on the test specimens.

Elektroisolierstoffe - Prüfverfahren für die Hydrolysebeständigkeit - Teil 2: Gehärtete Formstoffe

Matériaux isolants électriques - Méthodes d'essai concernant la stabilité hydrolytique - Partie 2: Matériaux thermodurcissables moulés

Décrit la méthode d'essai destinée à la détermination de la stabilité hydrolytique des matériaux thermodurcissables moulés, réalisés à partir de résines réagissant en durcissant à la temperature ambiente ou à chaud, lorsqu'elles sont soumises à l'influence simultanée de l'eau et d'une temperature élevée. Avec cette méthode, on mesure les modifications irréversibles des propriétés mécaniques et électriques, sans imposer de contrainte mécanique sur les éprouvettes.

Electrical insulating materials - Methods of test for the hydrolytic stability - Part 2: Moulded thermosets (IEC61234-2:1997)

General Information

Status
Published
Publication Date
10-Feb-1998
Withdrawal Date
30-Jun-1998
ICS
29.035.01 - Insulating materials in general
Technical Committee
CLC/SR 112 - Evaluation and qualification of electrical insulating materials and systems (to be defined)
Drafting Committee
IEC/TC 112 - IEC_TC_112
Parallel Committee
IEC/SC 15E - IEC_SC_15E
Current Stage
6060 - Document made available - Publishing
Start Date
11-Feb-1998
Completion Date
11-Feb-1998
Ref Project
SIST EN 61234-2:2001 - Electrical insulating materials - Methods of test for the hydrolytic stability -- Part 2: Moulded thermosets

Buy Standard

EN 61234-2:2001EN 61234-2:2001
PreviousNext
Standard
EN 61234-2:2001
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61234-2:2001
01-marec-2001
Electrical insulating materials - Methods of test for the hydrolytic stability - Part 2:
Moulded thermosets (IEC61234-2:1997)
Electrical insulating materials - Methods of test for the hydrolytic stability -- Part 2:
Moulded thermosets
Elektroisolierstoffe - Prüfverfahren für die Hydrolysebeständigkeit -- Teil 2: Gehärtete
Formstoffe
Matériaux isolants électriques - Méthodes d'essai concernant la stabilité hydrolytique --
Partie 2: Matériaux thermodurcissables moulés
Ta slovenski standard je istoveten z: EN 61234-2:1998
ICS:
29.035.01 Izolacijski materiali na Insulating materials in
splošno general
SIST EN 61234-2:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61234-2:20
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 62836:2024(Main)
Measurement of internal electric field in insulating materials - Pressure wave propagation method
SIST EN IEC 62836:2024

IEC 62836:2024 provides an efficient and reliable procedure to test the internal electric field in the insulating materials used for high-voltage applications, by using the pressure wave propagation (PWP) method. It is suitable for a planar and coaxial geometry sample with homogeneous insulating materials of thickness larger or equal to 0,5 mm and an electric field higher than 1 kV/mm, but it is also dependent on the thickness of the sample and the pressure wave generator. This first edition cancels and replaces IEC TS 62836 published in 2020. This edition includes the following significant technical changes with respect to IEC TS 62836: a) addition of Clause 12 for the measurement of space charge distribution in a planar sample; b) addition of Clause 13 for coaxial geometry samples; c) addition of Annex D with measurement examples for coaxial geometry samples; d) addition of a Bibliography; e) measurement examples for a planar sample have been moved from Clause 12 in IEC TS 62836 to Annex C.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62631-3-2:2023(Main)
Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC methods) - Surface resistance and surface resistivity
SIST EN IEC 62631-3-2:2024

IEC 62631-3-2:2023 describes methods of test for the determination of surface resistance and surface resistivity of electrical insulation materials by applying DC voltage. This edition includes the following significant technical changes with respect to the previous edition: a) descriptions of the electrode arrangements have been clarified; b) new descriptions of the conductive means have been added; c) a new informative Annex B summarizing the results of the comparative verification study on surface resistivities using different electrode arrangements has been added.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62631-3-1:2023(Main)
Dielectric and resistive properties of solid insulating materials - Part 3-1: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity - General method
SIST EN IEC 62631-3-1:2023

This part of IEC 62631 covers a method of test for the determination of volume resistance and volume resistivity of electrical insulating materials by applying a DC voltage.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60216-6:2023(Main)
Electrical insulating materials - Thermal endurance properties - Part 6: Determination of thermal endurance indices (TI and RTI) of an insulating material using the fixed time frame method
SIST EN IEC 60216-6:2023

This part of IEC 60216 specifies the experimental and calculation procedures for deriving the thermal endurance characteristics, temperature index (TI) and relative temperature index (RTI) of an electrical insulating material (EIM) using the "fixed time frame method (FTFM)". In this protocol, the ageing takes place for a small number of fixed times, using the appropriate number of ageing temperatures throughout each time, the properties of the specimens being measured at the end of the relevant time interval. This differs from the procedure of IEC 60216-1, where ageing is conducted at a small number of fixed temperatures, property measurement taking place after ageing times dependent on the progress of ageing. The diagnostic tests employed in the fixed time frame method are restricted to destructive tests. The method has not yet been applied to non-destructive or proof test procedures. Both the TI and the RTI determined according to the FTFM protocol are derived from experimental data obtained in accordance with the instructions of IEC 60216-1 and IEC 60216-2 as modified in this part of IEC 60216. The calculation procedures and statistical tests are modified from those of IEC 60216-3 and IEC 60216-5.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60216-5:2022(Main)
Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative temperature index (RTI) of an insulating material
SIST EN IEC 60216-5:2023

IEC 60216-5:2022 specifies the experimental and calculation procedures to be used for deriving the relative temperature index of a material from experimental data obtained in accordance with the instructions of IEC 60216-1 and IEC 60216-2. The calculation procedures are supplementary to those of IEC 60216-3. Guidance is also given for assessment of thermal ageing after a single fixed time and temperature, without extrapolation. This edition includes the following significant technical changes with respect to the previous edition:
Annex C “Computer program” has been completely reworked;
in 3.1, the terms “ATE” and “RTE” were replaced by “ATI” and “RTI” to emphasize their reference to an electrical insulating material (EIM).  This standard is to be read in conjunction with IEC 60216-1:2013, IEC 60216-2:2005 and IEC 60216-3:2021.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60544-5:2022(Main)
Electrical insulating materials - Determination of the effects of ionizing radiation - Part 5: Procedures for assessment of ageing in service
SIST EN IEC 60544-5:2022

This part of IEC 60544 covers ageing assessment methods which can be applied to components based on polymeric materials (e.g. cable insulation and jackets, elastomeric seals, polymeric coatings, gaiters) which are used in environments where they are exposed to radiation. The object of this standard is aimed at providing methods for the assessment of ageing in service. The approaches discussed in the following clauses cover ageing assessment programs based on condition monitoring (CM), the use of sample deposits in severe environments and sampling of real-time aged components.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62631-2-2:2022(Main)
Dielectric and resistive properties of solid insulating materials - Part 2-2: Relative permittivity and dissipation factor - High frequencies (1 MHz to 300 MHz) - AC methods
SIST EN IEC 62631-2-2:2022

This part of IEC 62631 specifies test methods for the determination of permittivity and dissipation factor properties of solid insulating materials in a high frequency range from 1 MHz to 300 MHz.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60587:2022(Main)
Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion
SIST EN IEC 60587:2022

This standard describes two test methods for the evaluation of electrical insulating materials for use under severe ambient conditions at power frequencies (45 Hz to 65 Hz) by the evaluation of the resistance to tracking and erosion, using a liquid contaminant and inclined plane specimens. The two methods are: - Method 1: test at constant voltage, - Method 2: test at stepwise increased voltage. Method 1 is the most widely used method as there is less need for continual inspection. The test conditions are designed to accelerate the production of the effects, but do not reproduce all the conditions encountered in service.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60112:2020(Main)
Method for the determination of the proof and the comparative tracking indices of solid insulating materials
SIST EN IEC 60112:2021

IEC 60112:2020 specifies the method of test for the determination of the proof and comparative tracking indices of solid insulating materials on pieces taken from parts of equipment and on plaques of material using alternating voltage. This document provides a procedure for the determination of erosion when required. This test method evaluates the composition of the material as well as the surface of the material being evaluated. Both the composition and surface condition directly influence the results of the evaluation and are considered when using the results in material selection process. Test results are not directly suitable for the evaluation of safe creepage distances when designing electrical apparatus. This basic safety publication focusing on a safety test method is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51. This edition includes the following significant technical changes with respect to the previous edition:  
Introduction of a new contaminant, solution C with a surfactant aligned with the test method of IEC 60587. The definition of the solution B was transferred to Annex B for backward reference.
Introduction of a screening test, considering the fact that some materials can withstand high test voltages, but fail at lower test voltages.  It has the status of a basic safety publication in accordance with IEC Guide 104.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62631-3-4:2019(Main)
Dielectric and resistive properties of solid insulating materials - Part 3-4: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity at elevated temperatures
SIST EN IEC 62631-3-4:2019

This part of IEC 62631 covers procedures for the determination of insulation resistance and volume resistivity of insulating materials by applying DC-voltage and temperatures up to 800 °C. The typical application materials include high temperature mica plate and alumina ceramics.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day