EN 60684-3-283:2011/A1:2014
(Amendment)Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation
This part of IEC 60684 gives the requirements for two types of heat-shrinkable, polyolefin sleeving for bus-bar insulation, with a nominal shrink ratio of 2,5:1. This sleeving has been found suitable up to temperatures of 100 °C.
– Type A : Medium wall Internal diameter up to 170,0 mm typically
– Type B : Thick wall Internal diameter up to 165,0 mm typically
These sleevings are normally supplied in colour, red or brown. Since these types of sleevings cover a significantly large range of sizes and wall thicknesses, Tables A.1 and A.2 provide guidance to the range of sizes available. The actual size and wall thickness shall be agreed between the user and supplier depending on the electric strength of the installed tubing offered and the requirements of the user. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 283: Polyolefin-Wärmeschrumpfschläuche für die Isolierung von Sammelschienen
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 283: Gaines thermorétractables en polyoléfine pour isolation de barre omnibus
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 283. list: Toplotno skrčljive poliolefinske cevi za izolacijo zbiralk - Dopolnilo A1 (IEC 60684-3-283:2010/A1:2013)
Ta del IEC 60684 podaja zahteve za dva tipa toplotno skrčljivih poliolefinskih cevi za izolacijo zbiralk, ki imajo nazivno razmerje krčenja do 2,5 : 1. Za te cevi je ugotovljeno, da so primerne za uporabo pri temperaturah do 100 °C.
- Tip A: Srednje debela stena. Notranji premer običajno do 170,0 mm.
- Tip B: Debela stena. Notranji premer običajno do 165,0 mm.
Te cevi se običajno dobavljajo v barvah, rdeči ali rjavi. Ker te vrste cevi zajemajo precej velik razpon velikosti in debelin stene, preglednici A.1 in A.2 podajata navodilo o razponu razpoložljivih velikosti. Dejanska velikost in debelina stene morata biti dogovorjeni med uporabnikom in dobaviteljem in sta odvisni od električne moči nameščenih cevi, ki so na voljo, in zahtev uporabnika. Materiali, skladni s to specifikacijo, ustrezajo vzpostavljenim ravnem delovanja. Vendar mora uporabnik material za določeno uporabo izbrati na podlagi dejanskih zahtev za ustrezno delovanje pri taki uporabi, ne le na podlagi same specifikacije.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60684-3-283:2011/A1:2014
01-julij-2014
*LENHL]RODFLMVNHFHYLGHO 6SHFLILNDFLMH]DSRVDPH]QHWLSHFHYLOLVW
7RSORWQRVNUþOMLYHSROLROHILQVNHFHYL]DL]RODFLMR]ELUDON'RSROQLOR$ ,(&
$
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet
283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 283:
Polyolefin-Wärmeschrumpfschläuche für die Isolierung von Sammelschienen
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines -
Feuille 283: Gaines thermorétractables en polyoléfine pour isolation de barre omnibus
Ta slovenski standard je istoveten z: EN 60684-3-283:2011/A1:2014
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
SIST EN 60684-3-283:2011/A1:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60684-3-283:2011/A1:2014
---------------------- Page: 2 ----------------------
SIST EN 60684-3-283:2011/A1:2014
EUROPEAN STANDARD
EN 60684-3-283/A1
NORME EUROPÉENNE
April 2014
EUROPÄISCHE NORM
ICS 29.035.20
English version
Flexible insulating sleeving -
Part 3: Specifications for individual types of sleeving -
Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation
(IEC 60684-3-283:2010/A1:2013)
Gaines isolantes souples - Isolierschläuche -
Partie 3: Spécifications pour types Teil 3: Anforderungen für einzelne
particuliers de gaines - Schlauchtypen -
Feuille 283: Gaines thermorétractables Blatt 283: Polyolefin-
en polyoléfine pour isolation de barre Wärmeschrumpfschläuche für die
omnibus Isolierung von Sammelschienen
(CEI 60684-3-283:2010/A1:2013) (IEC 60684-3-283:2010/A1:2013)
This amendment A1 modifies the European Standard EN 60684-3-283:2011; it was approved by CENELEC on
2014-01-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2014 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-283:2011/A1:2014 E
---------------------- Page: 3 ----------------------
SIST EN 60684-3-283:2011/A1:2014
EN 60684-3-283:2011/A1:2014 - 2 -
Foreword
The text of document 15/687/CDV, future IEC 60684-3-283:2010/A1, prepared by IEC/TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60684-3-283:2011/A1:2014.
The following dates are fixed:
(dop) 2014-10-16
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2017-01-16
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60684-3-283:2010/A1:2013 was approved by CENELEC as
a European Standard without any modification.
---------------------- Page: 4 ----------------------
SIST EN 60684-3-283:2011/A1:2014
IEC 60684-3-283
®
Edition 1.0 2013-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 1
AMENDEMENT 1
Flexible insulating sleeving –
Part 3: Specificat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.