EN 50152-3-1:2017

Railway applications - Fixed installations - Particular requirements for a.c. switchgear - Part 3-1: Measurement, control and protection devices for specific use in a.c. traction systems - Devices

This European Standard is applicable to new low voltage devices for measurement, control and protection which are: - for indoor or outdoor fixed installations in traction systems, and - operated in conjunction with high voltage equipment with an a.c. line voltage and frequency as specified in EN 50163. NOTE EN 50163 specifies the a.c. traction systems 15 kV 16,7 Hz and 25 kV 50 Hz. This European Standard also applies to measurement, control and protective devices other than low voltage devices and not covered by a specific railway product standard as far as reasonably possible. Requirements of this document prevail.

Bahnanwendungen - Ortsfeste Anlagen - Besondere Anforderungen an Wechselstrom-Schalteinrichtungen - Teil 3-1: Mess-, Steuerungs- und Schutzeinrichtungen für Wechselstrom-Bahnanlagen - Geräte

Dieser Schlussentwurf einer Europäischen Norm gilt für neue Niederspannungs-Mess-, -Steuerungs- und -Schutzeinrichtungen, die - für ortsfeste Innenraum- oder Freiluftanlagen in Bahnanlagen ausgelegt sind und - zusammen mit einer Hochspannungseinrichtung mit einer Fahrleitungswechselspannung und -frequenz entsprechend der EN 50163 betrieben werden. ANMERKUNG EN 50163 benennt für Bahnen die Wechselspannungssysteme 15 kV 16,7 Hz und 25 kV 50 Hz. Dieser Entwurf einer Europäischen Norm wird auch für Mess-, Steuerungs- und Schutzeinrichtungen gelten, die nicht Niederspannungsgeräte sind und die nicht von einer spezifischen Bahnproduktnorm umfasst sind, soweit dies vernünftigerweise möglich ist. Die Anforderungen dieses Dokumentes haben Vorrang.

Applications ferroviaires - Installations fixes - Exigences particulières pour appareillage à courant alternatif - Partie 3-1 : Dispositifs de mesure, de commande et de protection pour usage spécifique dans les systèmes de traction à courant alternatif - Appareillage

La présente Norme européenne est applicable aux nouveaux dispositifs basse tension de mesure, de commande et de protection qui sont: - destinés aux installations fixes intérieures ou extérieures dans les systèmes de traction, et - exploités conjointement avec des équipements haute tension à la tension et à la fréquence d’une ligne à courant alternatif tel que spécifié dans l'EN 50163. NOTE L'EN 50163 spécifie les réseaux de traction à courant alternatif de 15 kV 16,7 Hz et 25 kV 50 Hz. La présente Norme européenne s’applique également aux dispositifs de mesure, de commande et de protection autres que les dispositifs basse tension non couverts par une norme de produit ferroviaire spécifique dans toute la mesure du possible. Les exigences du présent document prévalent.

Železniške naprave - Stabilne naprave električne vleke - Posebne zahteve za stikalne naprave za izmenični tok - 3-1. del: Merilne, krmilne in zaščitne naprave za izključno uporabo v izmeničnih vlečnih sistemih - Naprave

Ta osnutek evropskega standarda se uporablja za nove nizkonapetostne naprave za merjenje, krmiljenje in zaščito, ki se:
– uporabljajo za notranje ali zunanje nameščene naprave v vlečnih sistemih in
– uporabljajo v povezavi z visokonapetostno opremo z izmenično napetostjo in frekvenco, kot je navedeno v standardu EN 50163.
OPOMBA: Standard EN 50163 določa vlečne sisteme z izmenično napetostjo 15 kV pri 16,7 Hz in 25 kV pri 50 Hz.
Ta osnutek evropskega standarda se uporablja tudi za merilne, krmilne in zaščitne naprave, ki niso nizkonapetostne naprave in niso zajete v posebnem standardu za železniške izdelke, v smiselno mogočem obsegu. Prednost imajo zahteve tega dokumenta.

General Information

• Status: Published
• Publication Date: 09-Feb-2017
• ICS: 29.130.20 - Low voltage switchgear and controlgear
• ICS: 29.280 - Electric traction equipment
• Technical Committee: CLC/TC 9X - Electrical and electronic applications for railways
• Drafting Committee: CLC/SC 9XC - Electric supply and earthing systems for public transport equipment and ancillary apparatus (fixed i
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 03-Nov-2021
• Ref Project: SIST EN 50152-3-1:2017 - Railway applications - Fixed installations - Particular requirements for a.c. switchgear - Part 3-1: Measurement, control and protection devices for specific use in a.c. traction systems - Devices

Relations

• Replaces: EN 50152-3-1:2003 - Railway applications - Fixed installations - Particular requirements for a.c. switchgear - Part 3-1: Measurement, control and protection devices for specific use in a.c. traction systems - Application guide
• Effective Date: 26-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2017
1DGRPHãþD
SIST EN 50152-3-1:2004
äHOH]QLãNHQDSUDYH6WDELOQHQDSUDYHHOHNWULþQHYOHNH3RVHEQH]DKWHYH]D
VWLNDOQHQDSUDYH]DL]PHQLþQLWRNGHO0HULOQHNUPLOQHLQ]DãþLWQHQDSUDYH]D
L]NOMXþQRXSRUDERYL]PHQLþQLKYOHþQLKVLVWHPLK1DSUDYH
Railway applications - Fixed installations - Particular requirements for a.c. switchgear -
Part 3-1: Measurement, control and protection devices for specific use in a.c. traction
systems - Devices
Bahnanwendungen - Ortsfeste Anlagen – Besondere Anforderungen an Wechselstrom-
Schalteinrichtungen - Teil 3-1: Mess-, Steuerungs- und Schutzeinrichtungen für
Wechselstrom-Bahnanlagen - Geräte
Applications ferroviaires - Installations fixes - Exigences particulières pour appareillage à
courant alternatif - Partie 3-1: Dispositifs de mesure, de commande et de protection pour
usage spécifique dans les systèmes de traction à courant alternatif - Guide d’application
Ta slovenski standard je istoveten z: EN 50152-3-1:2017
ICS:
29.130.99 Druge stikalne in krmilne Other switchgear and
naprave controlgear
29.280 (OHNWULþQDYOHþQDRSUHPD Electric traction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50152-3-1

NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2017
ICS 29.130.20; 29.280 Supersedes EN 50152-3-1:2003
English Version
Railway applications - Fixed installations - Particular
requirements for a.c. switchgear - Part 3-1: Measurement,
control and protection devices for specific use in a.c. traction
systems - Devices
Applications ferroviaires - Installations fixes - Exigences Bahnanwendungen - Ortsfeste Anlagen - Besondere
particulières pour appareillage à courant alternatif - Partie Anforderungen an Wechselstrom-Schalteinrichtungen - Teil
3-1 : Dispositifs de mesure, de commande et de protection 3-1: Mess-, Steuerungs- und Schutzeinrichtungen für
pour usage spécifique dans les systèmes de traction à Wechselstrom-Bahnanlagen - Geräte
courant alternatif - Guide d'application
This European Standard was approved by CENELEC on 2016-12-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50152-3-1:2017 E
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Specific requirements from the traction system . 6
5 Requirements on measurement, control and protection devices . 7
5.1 General . 7
5.2 Voltage detection systems . 7
5.3 Devices at supply voltage of a traction system . 7
5.4 Protection devices . 8
Annex A (informative) Application guide - Measurement principles . 9
A.1 Introduction . 9
A.2 Line testing . 9
A.2.1 General . 9
A.2.2 Line testing methods. 9
A.2.3 Line testing procedures . 11
Annex B (informative) Application guide - Control principles . 13
B.1 Introduction . 13
B.2 Closing control . 13
B.2.1 General . 13
B.2.2 Close inhibit . 13
B.2.3 On-command . 14
B.2.4 Auto-reclose . 15
B.3 Opening control . 15
B.3.1 General . 15
B.3.2 Auto-off sequences . 15
B.4 Automated sequences . 18
Bibliography . 19

Figures
Figure A.1 — Example of a feeder related line testing based on voltage criterion . 12

European foreword
This document (EN 50152-3-1:2017) has been prepared by CLC/SC 9XC “Electric supply and earthing
systems for public transport equipment and ancillary apparatus (Fixed installations)”.
The following dates are fixed:
– latest date by which the EN has to be implemented (dop) 2017-12-26
at national level by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) 2019-12-26
with the EN have to be withdrawn
This document supersedes EN 50152-3-1:2003.
It was completely reworked to:
— distinguish between requirements, Clauses 4 and 5, and application guides, annexes;
— include requirements on devices e.g. control and protection relays not included before;
— remove parts already included in other standards, e.g. EN 50633 protection principles.
The EN 50152 series is divided as follows:
— Railway applications — Fixed installations — Particular requirements for alternating current
switchgear — Part 1: Circuit-breakers with nominal voltage above 1 kV;
— Railway applications — Fixed installations — Particular requirements for alternating current
switchgear — Part 2: Disconnectors, earthing switches and switches with nominal voltage above 1 kV;
— Railway applications — Fixed installations — Particular requirements for a.c. switchgear — Part 3-1:
Measurement, control and protection devices for specific use in a.c. traction systems — Devices;
— Railway applications — Fixed installations — Particular requirements for a.c. switchgear — Part 3-2:
Measurement, control and protection devices for specific use in a.c. traction systems — Current
transformers;
— Railway applications — Fixed installations — Particular requirements for a.c. switchgear — Part 3-3:
Measurement, control and protection devices for specific use in a.c. traction systems — Voltage
transformers.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Introduction
EN 50152-3-1 is intended for measurement, control and protection devices for specific use in a.c. traction
systems other than current and voltage transformers. These are covered by EN 50152-3-2 and
EN 50152-3-3 respectively.
This standard covers a large variety of different kinds of equipment used in railway fixed installations which
do not have railway specific product standards. It provides clarification on how to select ratings and test
values relevant for operation in fixed installations. This standard needs to be read in conjunction with the
relevant product standard of the equipment concerned.
Annexes A and B are application guides. Annex A deals with railway specific measurement principles and
Annex B provides guidance in the design of control systems for a.c. traction. These application guides
identify characteristics of and parameters for procedures and functions used. Guidance in protection
principles is given in EN 50633.
The clause numbering of this part is different to that used in all other parts of the series. Clause numbering in
the other parts is the same as in the specific referenced product standard
1 Scope
This European Standard is applicable to new low voltage devices for measurement, control and protection
which are:
— for indoor or outdoor fixed installations in traction systems, and
— operated in conjunction with high voltage equipment with an a.c. line voltage and frequency as specified
in EN 50163.
NOTE EN 50163 specifies the a.c. traction systems 15 kV 16,7 Hz and 25 kV 50 Hz.
This European Standard also applies to measurement, control and protective devices other than low voltage
devices and not covered by a specific railway product standard as far as reasonably possible. Requirements
of this document prevail.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 50121-5, Railway applications — Electromagnetic compatibility — Part 5: Emission and immunity of fixed
power supply installations and apparatus
EN 50124-1, Railway applications - Insulation coordination - Part 1: Basic requirements - Clearances and
creepage distances for all electrical and electronic equipment
EN 50152-2:2012, Railway applications - Fixed installations - Particular requirements for alternating current
switchgear - Part 2: Disconnectors, earthing switches and switches with nominal voltage above 1 kV
EN 50152-3-2:2016, Railway applications - Fixed installations - Particular requirements for a.c. switchgear -
Part 3-2: Measurement, control and protection devices for specific use in a.c. traction systems - Current
transformers
EN 50152-3-3:2016, Railway applications - Fixed installations - Particular requirements for a.c. switchgear -
Part 3-3: Measurement, control and protection devices for specific use in a.c. traction systems - Voltage
transformers
EN 50163:2004 , Railway applications — Supply voltages of traction systems
EN 60255-1, Measuring relays and protection equipment - Part 1: Common requirements (IEC 60255-1)
EN 61243-5, Live working - Voltage detectors - Part 5: Voltage detecting systems (VDS) (IEC 61243-5)
EN 61869 (all parts), Instrument transformers (IEC 61869, all parts)
EN 61869-1:2009, Instrument transformers - Part 1: General requirements (IEC 61869-1:2007, modified)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 50152 (all parts) and the following
apply.
As impacted by EN 50163:2004/A1:2007, EN 50163:2004/Corrigendum:2010, EN 50163:2004/AC:2013.
EN 5015
...