EN 50632-2-22:2015
(Main)Electric motor-operated tools - Dust measurement procedure - Part 2-22: Particular requirements for cut-off machines and wall chasers
Electric motor-operated tools - Dust measurement procedure - Part 2-22: Particular requirements for cut-off machines and wall chasers
This clause of Part 1 is applicable except as follows: Addition: This part of EN 50632 applies to cut-off machines and wall chasers.
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-22: Besondere Anforderungen für Trennschleifmaschinen und Wandschlitzfräsen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-22: Exigences particulières pour les tronçonneuses
Elektromotorna orodja - Postopek meritve prahu - 2-22. del: Posebne zahteve za rezalne stroje
Ta točka 1. dela se ne uporablja v naslednjih primerih: ta del standarda EN 50632 velja za rezalnike in zidne rezkarje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2015
Elektromotorna orodja - Postopek meritve prahu - 2-22. del: Posebne zahteve za
rezalne stroje
Electric motor-operated electric tools - Dust measurement procedure - Part 2-22:
Particular requirements for cut-off machines
Ta slovenski standard je istoveten z: EN 50632-2-22:2015
ICS:
25.100.01 Rezalna orodja na splošno Cutting tools in general
25.140.20 (OHNWULþQDRURGMD Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 50632-2-22
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2015
ICS 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-22: Particular requirements for cut-off machines and wall
chasers
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2-22: Exigences particulières pour les Teil 2-22: Besondere Anforderungen für
tronçonneuses Trennschleifmaschinen und Wandschlitzfräsen
This European Standard was approved by CENELEC on 2015-08-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-22:2015 E
Contents
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test procedure . 4
5 Instrumentation . 7
6 Information to be reported . 7
Figures
Figure 101 – Test set-up for cut-off machines. 7
Figure 102 – Test set-up for wall chasers . 7
Figure 103 – A-support . 8
Tables
Table 101 — Operating conditions for cut-off machines . 5
Table 102 — Operating conditions for wall chasers . 6
European foreword
This document (EN 50632-2-22:2015) has been prepared by CLC/TC 116 “Safety of motor-operated
electric tools”.
The following dates are fixed:
(dop) 2016-08-03
• latest date by which this document has to be
implemented at national level by publication of
an identical national standard or by
endorsement
(dow) 2017-08-03
• latest date by which the national standards
conflicting with this document have to
be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This European Standard is divided into three parts:
Part 1: General requirements for the dust measurement which are common to electric motor-operated
tools (for the purpose of this standard referred to simply as tools);
Part 2 or 3: Requirements for the dust measurement for particular types of tools, which either
supplement or modify the requirements given in Part 1 to account for the particular characteristics of
these specific tools.
This Part 2 is to be used in conjunction with EN 50632-1:2015.
This Part 2 supplements or modifies the corresponding clauses in EN 50632-1:2015.
This Part 2 was developed to set out requirements for the measurement of the concentration for
inhalable and respirable dust emitted by cut-off machines and wall chasers.
Where a particular subclause of Part 1 is not mentioned in this Part 2, that subclause applies as far as
reasonable. When this standard states “addition”, “modification” or “replacement”, the relevant text in
Part 1 is to be adapted accordingly.
Subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 101.
The following print types are used:
- requirements; in roman type
- test specifications: in italic type;
- notes: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
1 Scope
This clause of Part 1 is applicable except as follows:
Addition:
This part of EN 50632 applies to cut-off machines and wall chasers.
2 Normative references
This cl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.