EN IEC 63356-1:2022
(Main)LED light source characteristics - Part 1: Data sheets
LED light source characteristics - Part 1: Data sheets
This part of IEC 63356 specifies datasheets of LED lamps and LED modules with a series of parameters per datasheet for a specific LED light source that enables interchangeability between products from different LED light source manufacturers. Compliance criteria relating to datasheet parameters in this document are covered by IEC 63220 for safety, or IEC 63221 for performance.
Eigenschaften von LED-Lichtquellen - Teil 1: Datenblätter
Caractéristiques de source lumineuse à LED - Partie 1: Feuilles de caractéristiques
L'IEC 63356-1:2022 spécifie les feuilles de caractéristiques des lampes à LED et des modules de LED à l'aide d'une série de paramètres par feuille de caractéristiques pour une source lumineuse à LED spécifique qui permet l'interchangeabilité entre les produits de différents fabricants de source lumineuse à LED.
Značilnosti LED-svetlobnega vira - 1. del: Preglednice (IEC 63356-1:2022)
Ta del standarda IEC 63356 določa podatkovne liste LED-sijalk in LED-modulov z nizom parametrov na posamezen podatkovni list za določen svetlobni vir LED, ki omogoča zamenljivost med izdelki različnih proizvajalcev svetlobnih virov LED.
Merila skladnosti glede varnosti, povezana s parametri podatkovnega lista v tem dokumentu, so zajeta v standardu IEC 632201, glede zmogljivosti pa v standardu IEC 632212.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2023
Značilnosti LED-svetlobnega vira - 1. del: Preglednice (IEC 63356-1:2022)
LED light source characteristics - Part 1: Data sheets (IEC 63356-1:2022)
Eigenschaften von LED-Lichtquellen - Teil 1: Datenblätter (IEC 63356-1:2022)
Caractéristiques de source lumineuse à LED - Partie 1: Feuilles de caractéristiques (IEC
63356-1:2022)
Ta slovenski standard je istoveten z: EN IEC 63356-1:2022
ICS:
29.140.01 Žarnice na splošno Lamps in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 63356-1
NORME EUROPÉENNE
EUROPÄISCHE NORM November 2022
ICS 29.140.99
English Version
LED light source characteristics - Part 1: Data sheets
(IEC 63356-1:2022)
Caractéristiques de source lumineuse à LED - Partie 1: Eigenschaften von LED-Lichtquellen - Teil 1: Datenblätter
Feuilles de caractéristiques (IEC 63356-1:2022)
(IEC 63356-1:2022)
This European Standard was approved by CENELEC on 2022-11-22. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63356-1:2022 E
European foreword
The text of document 34A/2297/FDIS, future edition 1 of IEC 63356-1, prepared by SC 34A "Electric
light sources" of IEC/TC 34 "Lighting" was submitted to the IEC-CENELEC parallel vote and approved
by CENELEC as EN IEC 63356-1:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-08-22
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-11-22
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 63356-1:2022 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 62931:2017 NOTE Harmonized as EN 62931:2017 (not modified)
IEC 63356-2 NOTE Harmonized as EN IEC 63356-2
IEC 63356-1 ®
Edition 1.0 2022-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
LED light source characteristics –
Part 1: Data sheets
Caractéristiques de source lumineuse à LED –
Partie 1: Feuilles de caractéristiques
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.140.99 ISBN 978-2-8322-5886-6
– 2 – IEC 63356-1:2022 © IEC 2022
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Overview and common information . 6
4.1 General . 6
4.2 Numbering system . 6
4.3 List of data sheets . 7
4.3.1 List of single-capped LED lamp data sheets . 7
4.3.2 List of double-capped LED lamp data sheets . 8
4.3.3 List of LED module data sheets . 8
5 Single-capped LED lamp data sheets . 8
6 Double-capped LED lamp data sheets . 8
6.1 Linear double-capped LED lamp with GX16t-5 caps . 8
6.1.1 Diagrammatic information for location of lamp dimensions . 8
6.1.2 Data sheets . 10
6.2 Linear double-capped LED lamp with GJ6.6 caps . 20
6.3 Linear double-capped LED lamp with GR6d caps . 20
7 LED module data sheets . 20
Bibliography . 21
Figure 1 – Location of dimensions of linear double-capped lamps with GX16t-5 caps . 9
Table 1 – List of data sheets for non-integrated double-capped LED lamps . 8
IEC 63356-1:2022 © IEC 2022 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LED LIGHT SOURCE CHARACTERISTICS –
Part 1: Data sheets
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 63356-1 has been prepared by subcommittee 34A: Electric light sources, of IEC technical
committee 34: Lighting. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
34A/2297/FDIS 34A/2312/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
– 4 – IEC 63356-1:2022 © IEC 2022
A list of all parts in the IEC 63356 series, published under the general title LED light source
characteristics, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IEC 63356-1:2022 © IEC 2022 – 5 –
INTRODUCTION
The IEC 63356 series (LED light source characteristics) is split into two parts:
• Part 1: Data sheets
The scope of Part 1 covers data sheets that are comprehensive specifications for unique
LED light sources (LED lamp or LED module). These are full specifications for products
including, where necessary, information on interchangeability aspects, for example
mechanical, electrical, optical.
Each data sheet in Part 1 relates to an individual type of LED lamp or LED module.
• Part 2: Design parameters and values
The scope of Part 2 covers design parameters and values that are used in the design of an
LED light source (LED lamp or LED module) or a related component. Part 2 does not provide
full product specifications but includes important interface aspects (e.g. mechanical,
electrical, optical) that should be taken account of in the design of LED light sources and
related components.
– 6 – IEC 63356-1:2022 © IEC 2022
LED LIGHT SOURCE CHARACTERISTICS –
Part 1: Data sheets
1 Scope
This part of IEC 63356 specifies data sheets of LED lamps and LED modules with a series of
parameters per data sheet for a specific LED light source that enables interchangeability
between products from different LED light source manufacturers.
Compliance criteria relating to data sheet parameters in this document are covered by
1 2
IEC 63220 for safety, or IEC 63221 for performance.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following
addresses:
• IEC Electropedia: available at https://www.electropedia.org
• ISO Online browsing platform: available at https://www.iso.org/obp
4 Overview and common information
4.1 General
Unless otherwise specified, mechanical dimensions refer to a temperature of (25 ± 5) °C.
4.2 Numbering system
Data sheets are numbered so that:
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.