EN 60317-20:2014

Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155

IEC 60317-20:2013 specifies the requirements of solderable enamelled round copper winding wire of class 155 with a sole coating based on polyurethane resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE: A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is: - Grade 1: 0,018 mm up to and including 0,800 mm; - Grade 2: 0,020 mm up to and including 0,800 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1:2013. This third edition cancels and replaces the second edition published in 1990, Amendment 1:1997 and Amendment 2:1999. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - new 3.2.2 containing general notes on winding wire, formerly a part of the scope; - revision to references to IEC 60317-0-1:2013 to clarify that their application is normative; - modification to Clause 15 to remove specific wire specimen sizes; - consolidation of 17.1 and 17.2 of the solderability requirements; - modification to Clause 19, Dielectric dissipation factor; - new Clause 23, Pin hole test. Key words: requirements of solderable enamelled round copper winding wire, class 155, sole coating based on polyurethane resin

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 20: Runddrähte aus Kupfer, verzinnbar, lackisoliert mit Polyurethan, Klasse 155

Spécifications pour types particuliers de fils de bobinage - Partie 20: Fil brasable de section circulaire en cuivre émaillé avec polyuréthane, classe 155

La CEI 60317-20:2013 spécifie les exigences pour les fils de bobinage brasables de section circulaire en cuivre émaillé de classe 155 avec un revêtement unique à base de résine polyuréthanne, qui peut être modifiée sous réserve de conserver l'identité chimique de la résine initiale et de répondre à toutes les exigences spécifiées pour le fil. NOTE - Une résine modifiée est une résine qui a subi une modification chimique, ou qui contient un ou plusieurs additifs pour améliorer les résultats obtenus ou les caractéristiques d'utilisation. La gamme des diamètres nominaux des conducteurs couverte par la présente norme est: - Grade 1: 0,018 mm jusqu'à 0,800 mm compris; - Grade 2: 0,020 mm jusqu'à 0,800 mm compris Les diamètres nominaux des conducteurs sont spécifiés dans l'Article 4 de la CEI 60317-0-1:2013. Cette troisième édition annule et remplace la deuxième édition parue en 1990, l'Amendement 1:1997 et l'Amendement 2:1999. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - un nouveau 3.2.2 contenant des notes générales sur le fil de bobinage intégrées auparavant au domaine d'application; - la révision des références à la CEI 60317-0-1:2013 pour bien établir que leur application est normative; - la modification de l'Article 15 pour retirer les tailles d'éprouvettes de fils spécifiques; - la consolidation de 17.1 et 17.2 des exigences relatives à la brasabilité; - la modification de l'Article 19, Facteur de dissipation diélectrique; - un nouvel Article 23, Détection des microfissures en immersion. Mots clés: exigences pour les fils de bobinage brasables de section circulaire en cuivre émaillé, classe 155, revêtement unique à base de résine polyuréthanne

Specifikacije za posebne vrste navijalnih žic - 20. del: S poliuretanom emajlirana okrogla bakrena žica, za spajkanje, razred 155 (IEC 60317-20:2013)

General Information

• Status: Published
• Publication Date: 13-Feb-2014
• Withdrawal Date: 13-Nov-2016
• ICS: 29.060.10 - Wires
• Technical Committee: CLC/TC 55 - Winding wires
• Drafting Committee: IEC/TC 55 - IEC_TC_55
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 14-Feb-2014
• Completion Date: 14-Feb-2014
• Ref Project: SIST EN 60317-20:2014 - Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155

Relations

• Replaces: EN 60317-20:1995 - Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155
• Effective Date: 29-Jan-2023
• Replaces: EN 60317-20:1995/A1:1998 - Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155
• Effective Date: 29-Jan-2023
• Replaces: EN 60317-20:1995/A2:2000 - Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155
• Effective Date: 29-Jan-2023
• Amended By: EN 60317-20:2014/A1:2019 - Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155
• Effective Date: 26-Jan-2023

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Specifikacije za posebne vrste navijalnih žic - 20. del: S poliuretanom emajlirana okrogla bakrena žica, za spajkanje, razred 155 (IEC 60317-20:2013)/Spécifications pour types particuliers de fils de bobinage - Partie 20: Fil de section circulaire en cuivre émaillé avec polyuréthanne brasable, classe 155Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 15529.060.10ŽiceWiresICS:Ta slovenski standard je istoveten z:EN 60317-20:2014SIST EN 60317-20:2014en01-april-2014SIST EN 60317-20:2014SLOVENSKI
STANDARDSIST EN 60317-20:2001/A2:2001SIST EN 60317-20:2001/A1:2002SIST EN 60317-20:20011DGRPHãþD



SIST EN 60317-20:2014



EUROPEAN STANDARD EN 60317-20 NORME EUROPÉENNE
EUROPÄISCHE NORM February 2014
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2014 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-20:2014 E
ICS 29.060.10 Supersedes EN 60317-20:1995 + A1:1998 + A2:2000
English version
Specifications for particular types of winding wires -
Part 20: Solderable polyurethane enamelled round copper wire, class 155 (IEC 60317-20:2013)
Spécifications pour types particuliers de fils de bobinage -
Partie 20: Fil brasable de section circulaire en cuivre émaillé avec polyuréthane, classe 155 (CEI 60317-20:2013)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten -
Teil 20: Runddrähte aus Kupfer, verzinnbar, lackisoliert mit Polyurethan, Klasse 155 (IEC 60317-20:2013)
This European Standard was approved by CENELEC on 2013-11-14. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 60317-20:2014



EN 60317-20:2014 - 2 - Foreword The text of document 55/1411/FDIS, future edition 3 of IEC 60317-20, prepared by IEC/TC 55 "Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-20:2014.
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-08-14 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-11-14
This document supersedes EN 60317-20:1995.
EN 60317-20:2014 includes the following significant technical changes with respect to EN 60317-20:1995: – new 3.2.2 containing general notes on winding wire, formerly a part of the scope; – revision to references to EN 60317-0-1:2014 to clarify that their application is normative; – modification to Clause 15 to remove specific wire specimen sizes; – consolidation of 17.1 and 17.2 of the solderability requirements; – modification to Clause 19, Dielectric dissipation factor; – new Clause 23, Pin hole test.
The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to reserve space for possible future wire requirements prior to those for wire packaging.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60317-20:2013 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified). IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified). IEC 60851 Series NOTE Harmonized as EN 60851 Series (not modified).
SIST EN 60317-20:2014



- 3 - EN
...