EN 50632-2-6:2015/A1:2019
(Amendment)Electric motor-operated tools - Dust measurement procedure - Part 2-6: Particular requirements for hammers
Electric motor-operated tools - Dust measurement procedure - Part 2-6: Particular requirements for hammers
This European Standard specifies general requirements for the dust measurement of electric motor-operated hammers supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected.
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-6: Besondere Anforderungen für Hämmer
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-6: Exigences particulières pour les marteaux
Elektromotorna orodja - Postopek meritve prahu - 2-6. del: Posebne zahteve za kladiva - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 50632-2-6:2015/A1:2020
01-januar-2020
Elektromotorna orodja - Postopek meritve prahu - 2-6. del: Posebne zahteve za
kladiva - Dopolnilo A1
Electric motor-operated tools - dust measurement procedure - Part 2-6: Particular
requirements for hammers
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-6: Besondere
Anforderungen für Hämmer
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-6:
Exigences particulières pour les marteaux
Ta slovenski standard je istoveten z: EN 50632-2-6:2015/A1:2019
ICS:
25.140.20 Električna orodja Electric tools
SIST EN 50632-2-6:2015/A1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 50632-2-6:2015/A1:2020
---------------------- Page: 2 ----------------------
SIST EN 50632-2-6:2015/A1:2020
EUROPEAN STANDARD EN 50632-2-6:2015/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2019
ICS 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-6: Particular requirements for hammers
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2-6: Exigences particulières pour les Teil 2-6: Besondere Anforderungen für Hämmer
marteaux
This amendment A1 modifies the European Standard EN 50632-2-6:2015; it was approved by CENELEC on 2019-10-21. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-6:2015/A1:2019 E
---------------------- Page: 3 ----------------------
SIST EN 50632-2-6:2015/A1:2020
EN 50632-2-6:2015/A1:2019 (E)
Contents Page
European foreword . 3
1 Modifications to 4.3 . 4
2
---------------------- Page: 4 ----------------------
SIST EN 50632-2-6:2015/A1:2020
EN 50632-2-6:2015/A1:2019 (E)
European foreword
This document (EN 50632-2-6:2015/A1:2019) has been prepared by CLC/TC 116 “Safety of motor-
operated electric tools”.
This amendment was developed to specify how the mass of the tool and the concrete formulation is
determined.
The following dates are fixed:
• latest date by which the amendment has to be implemented (dop) 2020-10-21
at national level by publication of an identical
national standard or by endorsement
• latest date by which the national standards conflicting (dow) 2021-10-21
with the amendment have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
3
---------------------- Page: 5 ----------------------
SIST EN 50632-2-6:2015/A1:2020
EN 50632-2-6:2015/A1:2019 (E)
1 Modifications to 4.3
Replace Table 101 with the following:
Table 101 — Operating conditions for rotary hammers
Material Concrete block without a reinforcement having the formulation specified in Table 102
and set-up and having the minimum dimensions 500 mm × 500 mm and 200 mm in height.
After the 28 days as specified in Table 102, the concrete block shall be stored for
another three weeks under dry conditions.
For rotary hammers with a mass less than or equal to 5 kg, the concrete block is placed
on a A-support, see Figure 101, with 15
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.