EN 60317-0-1:2008
(Main)Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
This part of IEC 60317 specifies general requirements of enamelled round copper winding wires with or without bonding layer. The main changes with respect to the previous edition are:
- addition of Grade 3 minimum insulation increases and maximum overall diameters for wires up to 0,071 mm nominal conductor diameter in Tables 1 and A.1;
- revisions to minimum increase in bonding layer for wires up to 0,100 mm nominal conductor diameter in Tables 2 and A.2;
- addition of Grade 3 dielectric breakdown requirements for wires up to 0,071 mm nominal conductor diameter; and
- new pin hole test requirement for Grade 3 polyurethane wires.
This standard is to be read in conjunction with the IEC 60851 series. The clause numbers used in this part of IEC 60317 are identical with the respective test numbers of IEC 60851.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-1: Allgemeine Anforderungen - Runddrähte aus Kupfer, lackisoliert
Spécifications pour types particuliers de fils de bobinage - Partie 0-1: Exigences générales - Fil de section circulaire en cuivre émaillé
La présente partie de la CEI 60317 spécifie les exigences générales pour les fils de bobinage de section circulaire en cuivre émaillé avec ou sans couche adhérente. Les changements principaux par rapport à l'édition précédente sont:
- ajout, dans les Tableaux 1 et A.1, de l'accroissement minimal dû à l'isolant de Grade 3 et des diamètres extérieurs maximaux pour les fils de diamètre nominal du conducteur jusqu'à 0,071 mm;
- révisions apportées à l'accroissement minimal de la couche adhérente pour les fils de diamètre nominal du conducteur jusqu'à 0,100 mm, dans les Tableaux 2 et A.2;
- ajout des exigences de claquage du diélectrique de Grade 3 pour les fils de diamètre nominal du conducteur jusqu'à 0,071 mm; et
- nouvelle exigence de détection des microfissures en immersion pour les fils émaillés avec polyuréthanne de Grade 3.
Cette norme doit être lue conjointement avec la série CEI 60851. Les numéros d'articles dans la présente partie de la CEI 60317 sont identiques aux numéros d'essais respectifs de la CEI 60851.
Specifikacije za posebne tipe navitij - 0-1. del: Splošne zahteve - Emajliran okrogel bakren vodnik (IEC 60317-0-1:2008)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2008
1DGRPHãþD
SIST EN 60317-0-1:2001
SIST EN 60317-0-1:2001/A1:2001
SIST EN 60317-0-1:2001/A2:2006
Specifikacije za posebne tipe navitij - 0-1. del: Splošne zahteve - Emajliran okrogel
bakren vodnik (IEC 60317-0-1:2008)
Specifications for particular types of winding wires - Part 0-1: General requirements -
Enamelled round copper wire
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-1:
Allgemeine Anforderungen - Runddrähte aus Kupfer, lackisoliert
Spécifications pour types particuliers de fils de bobinage - Partie 0-1: Prescriptions
générales - Fil de section circulaire en cuivre émaillé
Ta slovenski standard je istoveten z: EN 60317-0-1:2008
ICS:
29.060.10 Žice Wires
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 60317-0-1
NORME EUROPÉENNE
June 2008
EUROPÄISCHE NORM
ICS 29.060.10 Supersedes EN 60317-0-1:1998 + A1:2000 + A2:2005
English version
Specifications for particular types of winding wires -
Part 0-1: General requirements -
Enamelled round copper wire
(IEC 60317-0-1:2008)
Spécifications pour types particuliers Technische Lieferbedingungen
de fils de bobinage - für bestimmte Typen von Wickeldrähten -
Partie 0-1: Exigences générales - Teil 0-1: Allgemeine Anforderungen -
Fil de section circulaire en cuivre émaillé Runddrähte aus Kupfer, lackisoliert
(CEI 60317-0-1:2008) (IEC 60317-0-1:2008)
This European Standard was approved by CENELEC on 2008-05-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-0-1:2008 E
Foreword
The text of document 55/1033/CDV, future edition 3 of IEC 60317-0-1, prepared by IEC TC 55, Winding
wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60317-0-1 on 2008-05-01.
This European Standard supersedes EN 60317-0-1:1998 + A1:2000 + A2:2005.
The main changes with respect to EN 60317-0-1:1998 are listed below:
– addition of Grade 3 minimum insulation increases and maximum overall diameters for wires up to
0,071 mm nominal conductor diameter in Tables 1 and A.1;
– revisions to minimum increase in bonding layer for wires up to 0,100 mm nominal conductor diameter
in Tables 2 and A.2;
– addition of Grade 3 dielectric breakdown requirements for wires up to 0,071 mm nominal conductor
diameter;
– new pin hole test requirement for Grade 3 polyurethane wires.
This standard is to be read in conjunction with the EN 60851 series. The clause numbers used in
EN 60317-0-1 are identical with the respective test numbers of EN 60851.
In case of inconsistencies between EN 60851 and EN 60317-0-1, the latter shall prevail.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2009-02-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2011-05-01
Annex ZA has been added by CENELEC.
__________
- 3 - EN 60317-0-1:2008
Endorsement notice
The text of the International Standard IEC 60317-0-1:2008 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60317-2 NOTE Harmonized as EN 60317-2:1994 (not modified).
IEC 60317-4 NOTE Harmonized as EN 60317-4:1994 (not modified).
IEC 60317-11 NOTE Harmonized as EN 60317-11:2000 (not modified).
IEC 60317-19 NOTE Harmonized as EN 60317-19:1995 (not modified).
IEC 60317-20 NOTE Harmonized as EN 60317-20:1995 (not modified).
IEC 60317-21 NOTE Harmonized as EN 60317-21:1995 (not modified).
IEC 60317-23 NOTE Harmonized as EN 60317-23:1995 (not modified).
IEC 60317-35 NOTE Harmonized as EN 60317-35:1994 (not modified).
IEC 60317-36 NOTE Harmonized as EN 60317-36:1994 (not modified).
IEC 60317-51 NOTE Harmonized as EN 60317-51:2001 (not modified).
__________
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60172 - Test procedure for the determination of the EN 60172 1994
temperature index of enamelled winding wires
IEC 60264 Series Packaging of winding wires EN 60264 Series
IEC 60317 Series Specifications for particular types of winding EN 60317 Series
wires
IEC 60851 Series Winding wires - Test methods EN 60851 Series
1)
ISO 3 - Preferred numbers - Series of preferred - -
numbers
1)
Undated reference.
2)
Valid edition at date of issue.
IEC 60317-0-1
Edition 3.0 2008-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 0-1: General requirements – Enamelled round copper wire
Spécifications pour types particuliers de fils de bobinage –
Partie 0-1: Exigences générales – Fil de section circulaire en cuivre émaillé
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
U
CODE PRIX
ICS 29.060.10 ISBN 2-8318-9636-3
– 2 – 60317-0-1 © IEC:2008
CONTENTS
FOREWORD.4
INTRODUCTION.6
1 Scope.7
2 Normative references.7
3 Terms, definitions and general notes on methods of test and appearance.7
3.1 Terms and definitions .7
3.2 General notes on methods of test .9
3.3 Appearance .9
4 Dimensions.9
4.1 Conductor diameter .9
4.2 Out of roundness of conductor (nominal conductor diameters over 0,063 mm) .12
4.3 Minimum increase in diameter due to the insulation and the bonding layer
(nominal conductor diameters over 0,063 mm).12
4.3.1 Enamelled wires without a bonding layer .12
4.3.2 Enamelled wires with a bonding layer .12
4.4 Maximum overall diameter .12
4.4.1 Enamelled wires without a bonding layer .12
4.4.2 Enamelled wires with a bonding layer .12
5 Electrical resistance.12
6 Elongation .13
7 Springiness.13
7.1 Nominal conductor diameters from 0,080 mm up to and including 1,600 mm .13
7.2 Nominal conductor diameters over 1,600 mm.13
8 Flexibility and adherence .15
8.1 Mandrel winding test (nominal conductor diameters up to and including
1,600 mm) .15
8.2 Stretching test (nominal conductor diameters over 1,600 mm).15
8.3 Jerk test (nominal conductor diameters up to and including 1,000 mm) .15
8.4 Peel test (nominal conductor diameters over 1,000 mm) .15
9 Heat shock .15
9.1 Nominal conductor diameters up to and including 1,600 mm .15
9.2 Nominal conductor diameters over 1,600 mm.16
10 Cut-through .16
11 Resistance to abrasion .16
12 Resistance to solvents .16
13 Breakdown voltage .16
13.1 Nominal conductor diameters up to and including 0,100 mm .17
13.2 Nominal conductor diameters over 0,100 mm up to and including 2,500 mm.17
13.3 Nominal conductor diameters over 2,500 mm.18
14 Continuity of insulation (nominal conductor diameters up to and including
1,600 mm) .19
15 Temperature index.19
16 Resistance to refrigerants .19
17 Solderability.19
60317-0-1 © IEC:2008 – 3 –
18 Heat or solvent bonding .19
19 Dielectric dissipation factor .19
20 Resistance to transformer oil .19
21 Loss of mass .19
23 Pin hole test .20
30 Packaging .20
Annex A (informative) Dimensions for intermediate nominal conductor diameters (R 40) .21
Annex B (informative) Method for the calculation of linear resistance .24
Annex C (informative) Resistance .26
Bibliography .28
Table 1 – Dimensions of enamelled wires (R 20) .10
Table 2 – Dimensions of enamelled wires with a bonding layer (R 20).11
Table 3 – Electrical resistances .12
Table 4 – Elongation .13
Table 5 – Springiness.14
Table 6 – Mandrel winding.15
Table 7 – Heat shock .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.