EN 60317-0-1:2014
(Main)Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
IEC 60317-0-1:2013 specifies general requirements of enamelled round copper winding wires with or without bonding layer. The range of nominal conductor diameters is given in the relevant specification sheet. This fourth edition cancels and replaces the third edition published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - revision to the definition of nominal conductor dimension; - new subclause containing general notes on winding wire, formerly a part of the scope; - revision to elongation requirements in Table 4; - revisions to Clause 13, Breakdown voltage, to include new requirements for intermediate wire diameters; - revision to continuity of insulation requirements in Table 13; - revision to the introduction of Annex A; - revision to B.2 of Annex B; - revision to Table C.1 of Annex C. Keywords: requirements of enamelled round copper winding wires
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-1: Allgemeine Anforderungen - Runddrähte aus Kupfer, lackisoliert
Spécifications pour types particuliers de fils de bobinage - Partie 0-1: Exigences générales - Fil de section circulaire en cuivre émaillé
La CEI 60317-0-1:2013 spécifie les exigences générales pour les fils de bobinage de section circulaire en cuivre émaillé avec ou sans couche adhérente. La gamme des diamètres nominaux des conducteurs est donnée dans la feuille de spécification appropriée. Cette quatrième édition annule et remplace la troisième édition parue en 2008. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - la révision de la définition de la dimension nominale du conducteur; - un nouveau paragraphe contenant des notes générales sur le fil de bobinage intégrées auparavant au domaine d'application; - révision des exigences d'allongement dans le Tableau 4; - révision de l'Article 13, Tension de claquage, pour inclure de nouvelles exigences pour les diamètres de fils intermédiaires; - révision des exigences de continuité de l'isolant dans le Tableau 13; - révision de l'introduction de l'Annexe A; - révision du B.2 de l'Annexe B; - révision du Tableau C.1 de l'Annexe C. Mots clés: exigences pour les fils de bobinage de section circulaire en cuivre émaillé
Specifikacije za posebne vrste navijalnih žic - 0-1. del: Splošne zahteve - Prevlečena okrogla bakrena žica
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Spécifications pour types particuliers de fils de bobinage - Parte 0-1: Prescriptions générales - Fil de section circulaire en cuivre émailléSpecifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire77.150.30Bakreni izdelkiCopper products29.060.10ŽiceWiresICS:Ta slovenski standard je istoveten z:EN 60317-0-1:2014SIST EN 60317-0-1:2014en01-marec-2014SIST EN 60317-0-1:2014SLOVENSKI
STANDARDSIST EN 60317-0-1:20081DGRPHãþD
EUROPEAN STANDARD EN 60317-0-1 NORME EUROPÉENNE
EUROPÄISCHE NORM January 2014
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2014 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-0-1:2014 E
ICS 29.060.10 Supersedes EN 60317-0-1:2008
English version
Specifications for particular types of winding wires -
Part 0-1: General requirements -
Enamelled round copper wire (IEC 60317-0-1:2013)
Spécifications pour types particuliers de fils de bobinage -
Partie 0-1: Exigences générales -
Fil de section circulaire en cuivre émaillé (CEI 60317-0-1:2013)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten -
Teil 0-1: Allgemeine Anforderungen -
Runddrähte aus Kupfer, lackisoliert (IEC 60317-0-1:2013)
This European Standard was approved by CENELEC on 2013-11-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-08-11 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-11-11
This document supersedes EN 60317-0-1:2008.
This standard is to be read in conjunction with the EN 60851 series. The clause numbers used in this part of EN 60317 are identical with the respective test numbers of the EN 60851 series.
In case of inconsistencies between EN 60851 and this part of EN 60317, the latter prevails.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60317-0-1:2013 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified). IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified).
- 3 - EN 60317-0-1:2014 Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60172 - Test procedure for the determination of the temperature index of enamelled winding wires EN 60172 -
IEC 60851 Series Winding wires - Test methods EN 60851 Series
ISO 3 - Preferred numbers - Series of preferred numbers - -
IEC 60317-0-1 Edition 4.0 2013-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires –
Part 0-1: General requirements – Enamelled round copper wire
Spécifications pour types particuliers de fils de bobinage –
Partie 0-1: Exigences générales – Fil de section circulaire en cuivre émaillé
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE V ICS 29.060.10 PRICE CODE CODE PRIX ISBN 978-2-8322-1150-2
– 2 – 60317-0-1 © IEC:2013
CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope . 7 2 Normative references . 7 3 Terms, definitions, general notes and appearance . 7 3.1 Terms and definitions . 7 3.2 General notes . 8 3.2.1 Methods of test . 8 3.2.2 Winding wire . 9 3.3 Appearance . 9 4 Dimensions . 9 4.1 Conductor diameter . 9 4.2 Out of roundness of conductor (nominal conductor diameters over 0,063 mm). 13 4.3 Minimum increase in diameter due to the insulation and the bonding layer (nominal conductor diameters over 0,063 mm) . 13 4.3.1 Enamelled wires without a bonding layer . 13 4.3.2 Enamelled wires with a bonding layer . 13 4.3.3 Intermediate nominal conductor diameters . 13 4.4 Maximum overall diameter . 13 4.4.1 Enamelled wires without a bonding layer . 13 4.4.2 Enamelled wires with a bonding layer . 14 5 Electrical resistance . 14 6 Elongation . 15 7 Springiness . 15 7.1 Nominal conductor diameters from 0,080 mm up to and including 1,600 mm . 15 7.2 Nominal conductor diameters over 1,600 mm . 15 8 Flexibility and adherence . 17 8.1 Mandrel winding test (nominal conductor diameters up to and including 1,600 mm) . 17 8.2 Stretching test (nominal conductor diameters over 1,600 mm) . 17 8.3 Jerk test (nominal conductor diameters up to and including 1,000 mm) . 17 8.4 Peel test (nominal conductor diameters over 1,000 mm) . 17 9 Heat shock . 18 9.1 Nominal conductor diameters up to and including 1,600 mm. 18 9.2 Nominal conductor diameters over 1,600 mm . 18 10 Cut-through . 19 11 Resistance to abrasion . 19 12 Resistance to solvents . 19 13 Breakdown voltage . 19 13.1 General . 19 13.2 Nominal conductor diameters up to and including 0,100 mm. 19 13.3 Nominal conductor diameters over 0,100 mm up to and including 2,500 mm . 21 13.4 Nominal conductor diameters over 2,500 mm . 23 14 Continuity of insulation (nominal conductor diameters up to and including 1,600 mm) . 24 15 Temperature index . 24 SIST EN 60317-0-1:2014
60317-0-1 © IEC:2013 – 3 –
16 Resistance to refrigerants . 24 17 Solderability . 24 18 Heat or solvent bonding . 24 19 Dielectric dissipation factor . 24 20 Resistance to transformer oil . 24 21 Loss of mass . 24 23 Pin hole test . 25 30 Packaging. 25 Annex A (informative)
Dimensions for intermediate nominal conductor diameters (R 40) . 26 Annex B (informative)
Method for the calculation of linear resistance . 30 Annex C (informative)
Resistance. 32 Bibliography . 34
Table 1 – Dimensions of enamelled wires (R 20) – Preferred nominal conductor diameters (1 of 2) . 10 Table 2 – Dimensions of enamelled wires with a bonding layer (R 20) –
Preferred nominal conductor diameters (1 of 2) . 12 Table 3 – Electrical resistance . 14 Table 4 – Elongation . 15 Table 5 – Springiness . 16 Table 6 – Mandrel winding . 17 Table 7 – Heat shock . 18 Table 8 – Breakdown voltage – Preferred nominal conductor diameters (R 20) (0,018 mm up to and including 0,100 mm) . 20 Table 9 – Breakdown voltage – Intermediate nominal conductor diameters (R 40) (0,019 mm up to and including 0,095 mm) . 21 Table 10 – Breakdown voltage – Prefer
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.