EN 60122-3:2001
(Main)Quartz crystal units of assessed quality - Part 3: Standard outlines and lead connections
Quartz crystal units of assessed quality - Part 3: Standard outlines and lead connections
Specifies the outline dimensions and lead connections of quartz crystal units with lead enclosures.
Schwingquarze mit bewerteter Qualität - Teil 3: Norm-Gehäusemaße und Anschlussdrähte
Résonateurs à quartz sous assurance de la qualité - Partie 3: Encombrements normalisés et connexions des sorties
Spécifie les encombrements normalisés et les connexions des sorties des résonateurs à quartz comportant des enveloppes avec sorties.
Quartz crystal units of assessed quality - Part 3: Standard outlines and lead connections (IEC 60122-3:2001)
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 60122-3:2002
prva izdaja
STANDARD
september 2002
Quartz crystal units of assessed quality - Part 3: Standard outlines and lead
connections (IEC 60122-3:2001)
ICS 31.140 Referenčna številka
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD EN 60122-3
NORME EUROPÉENNE
EUROPÄISCHE NORM October 2001
ICS 31.140
English version
Quartz crystal units of assessed quality
Part 3: Standard outlines and lead connections
(IEC 60122-3:2001)
Résonateurs à quartz sous assurance de Schwingquarze mit bewerteter Qualität
la qualité Teil 3: Norm-Gehäusemaße und
Partie 3: Encombrements normalisés et Anschlussdrähte
connexions des sorties (IEC 60122-3:2001)
(CEI 60122-3:2001)
This European Standard was approved by CENELEC on 2001-10-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,
Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60122-3:2001 E
Foreword
The text of document 49/493/FDIS, future edition 3 of IEC 60122-3, prepared by IEC TC 49,
Piezoelectric and dielectric devices for frequency control and selection, was submitted to the IEC-
CENELEC parallel vote and was approved by CENELEC as EN 60122-3 on 2001-10-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2002-01-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2004-10-01
__________
Endorsement notice
The text of the International Standard IEC 60122-3:2001 was approved by CENELEC as a European
Standard without any modification.
__________
�����
���
�������������� ���
�������
�������������
�����������������
��������
�������������
�������
�����������������������������������
���������������
���������
����� ���������������������������!����
�����������
"��������#������������$����������������#��
�������
%�������������������������������������
©�����������������������$���" ����������%����⎯����$&��’�����#�����’���������%��
�" "���$#�������� �����$"(�� #��������$�"��)������$���"������ ���$#����*������$"(�� #������#&�(����$���" ������"����.�����
"����������"��!"��!"��*�����!"�� ����������$#��#" "��$�� ���+ #�&� *���� ��� (&� #�&� ��#��+� ��� ����� � ��� �� �#�� #�+
��� �����!"���"� �� #��!"�+� &� ��$�����#�$���� �$��� ������ �� �"���’�$���� �$&��’�#����� ��*���+�/����"��$������������
�� ��*����+��#����,# ����� ��������,�����"�- /�����’�*��������$"(������-
������#����#����� ����� ��� #������������ 0+��"�����1#���(���2���%#+��/��.���#��
����*#34�56�����7�7��0�� ���#��4����#��8�� - � �����/�(����������$499///-�� - �
�����:��;
������������ ��� ����� ���!"�� ������#����#��
:���������
�������#����#�� ��� ����� ��� #�� ����������
������������������������������������
��������������������������������
60122-3 © IEC:2001 – 3 –
CONTENTS
Page
FOREWORD . 5
INTRODUCTION .9
Clause
1 Scope .11
2 Guidance for the standardization of outline drawings for frequency control and
selection devices .11
3 Dimensions of quartz crystal unit enclosures .15
4 Designation of quartz crystal unit enclosures .15
Specification sheets 1 to 22 .19 to 61
Bibliography.63
60122-3 © IEC:2001 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
QUARTZ CRYSTAL UNITS OF ASSESSED QUALITY –
Part 3: Standard outlines and lead connections
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the
two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60122-3 has been prepared by IEC technical committee 49:
Piezoelectric and dielectric devices for frequency control and selection.
The text of this standard is based on the following documents:
FDIS Report on voting
49/493/FDIS 49/508/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This third edition cancels and replaces the second edition published in 1977, amendment 1
(1984), amendment 2 (1991), amendment 3 (1992) and amendment 4 (1993). This third
edition constitutes a technical revision.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.
IEC 60122 will consist, after revision, of the following parts under the general title: Quartz
crystal units of assessed quality:
– Part 1: Generic specification (IEC 61178-1 at present)
– Part 2: Guide to the use of quartz crystal units for frequency control and selection
– Part 3: Standard outlines and lead connections
60122-3 © IEC:2001 – 7 –
– Part 4: Sectional specification – Capability approval (IEC 61178-2 at present)
– Part 4-1: Sectional specification – Capability approval – Section 1: Blank detail
specification (IEC 61178-2-1 at present)
– Part 5: Sectional specification – Qualification approval (IEC 61178-3 at present)
– Part 5-1: Sectional specification – Qualification approval – Section 1: Blank detail
specification (IEC 61178-3-1 at present).
The committee has decided that the contents of this publication will remain unchanged until
2006. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
60122-3 © IEC:2001 – 9 –
INTRODUCTION
The second edition of IEC 60122-3 (1977) and its amendments 1 to 4 contained 51 enclosure
types showing the dimensional and geometrical characteristics of these enclosures. Since its
release, due to progress in technology, many of the enclosures given in the standard have
.
become obsolete
Bearing this in mind, technical committee 49 has issued a questionnaire on all outlines
contained in IEC 60122-3. Based on the replies received, technical committee 49 made a
decision at the meeting held in Rotterdam in June 1996 to retain only enclosures which
remained in “wide usage”. These enclosures are specified in the present standard.
The following 24 enclosure types have been deleted from the second edition of IEC 60122-3
(1977) and its amendments 1 to 4.
BG, BG/1, BH, BH/1, BH/2, BJ, BJ/1,
BJ/2, CL, DB, DD, DE, DF, DG,
DH, EF, EG, CU 03 A., CU 03 B., CU 03 C.,
CU 03 .1, CU 03 .2, CU 04 .2, CU 05 D.
60122-3 © IEC:2001 – 11 –
QUARTZ CRYSTAL UNITS OF ASSESSED QUALITY –
Part 3: Standard outlines and lead connections
1 Scope
This part of IEC 60122 specifies the outline dimensions and lead connections of quartz crystal
units with lead enclosures.
2 Guidance for the standardization of outline drawings for frequency control
and selection devices
In order to achieve a uniform presentation of all outline drawings for frequency control and
selection devices, the following shall be considered.
2.1 An outline drawing shall show all dimensional and geometrical characteristics of an
enclosure necessary to ensure mechanical interchangeability with all other enclosures of the
same outline. Enlarged detail view may be used, if necessary.
The outline drawing shall consist of three parts:
2.2
2.2.1 A drawing with dimensional symbols (capital letter) as shown in figure 1 with
applicable notes, if necessary.
2.2.2 A tabular listing relating the drawing symbols to the actual dimensions. Where
possible, this shall be shown on the same page as the drawing.
2.2.3 An “actual-size” sketch (scale 1:1).
The outline drawing shall be executed in the third-angle projection.
2.3
2.4 The function and identification of the lead connections (termination) shall be determined
by agreement between the supplier and user. They shall not be defined on the outline
drawing.
2.5 Descriptive notes may be used at the bottom of, or adjacent to, the drawing with proper
reference to the body of the drawing.
All dimensions shall be in millimetres.
2.6
2.7 Outline dimensions A, B, C, D and E shall be listed with maximum values only.
2.8 Lead (termination) cross-sectional dimensions shall be listed with minimum and
maximum values. If applicable, nominal dimensions may be added.
2.9 The spacing of the leads (termination) – symbol H – shall be listed with minimum,
nominal and maximum dimensions.
60122-3 © IEC:2001 – 13 –
E
D
Actual size
C
U
L
W
H
K B
A
IEC 842/01
Dimensions (mm)
Notes
Ref.
Types
Min. Nom. Max.
A – – x
–
B – x
C –– x
D –– x
E –– x
H xxx
K x–x 1
L
x–x
U x– – 2
W x– – 2
NOTE 1 ….
NOTE 2 ….
Scale
2:1
Figure 1 – Guidance for outline drawings
Sheet … Date:
60122-3 © IEC:2001 – 15 –
2.10 Leads (terminations) for soldering application shall be specified with the minimum
length dimensions (symbol L) only.
Leads (terminations) for plug-in application shall be specified with minimum and maximum
length dimensions.
2.11 If leads (terminations) are provided with an undercut, dimensions U and W shall be
listed with minimum dimensions only.
3 Dimensions of quartz crystal unit enclosures
The dimensions in this standard apply to the completed quartz crystal units.
Only those dimensions which meet the requirements of the guidance for standardization of
outline drawings are given (see clause 2).
4 Designation of quartz crystal unit enclosures
Table 1 – Designation of quartz crystal unit enclosures
No. Type Sheet No. Description
AA
1 Sheet 1 Metal, solder-sealed, two-lead crystal unit outline
AB
BC
2 Sheet 2 Metal, solder-sealed, two-lead crystal unit outline
BC/1
BF
3 Sheet 3 Metal, solder-sealed, two-lead crystal unit outline
BF/1
CK, CM
4 Sheet 4 Metal, welded, three-lead crystal unit outline
CN, CP
5 CX Sheet 5 Metal, solder-sealed, two-lead crystal unit outline
CY, CY/1
6 Sheet 6 Glass, two-lead crystal unit outline
CZ
DA
7 Sheet 7 Glass, two-lead crystal unit outline
DC
8 DK Sheet 8 Metal, welded, three-lead crystal unit outline
9 DL Sheet 9 Metal, welded, five-lead crystal unit outline
10 DN Sheet 10 Metal, welded, two-lead crystal unit outline
DP
11 Sheet 11 Metal, welded, two-lead crystal unit outline
EH
12 DQ Sheet 12 Metal, welded, two-lead crystal unit outline
13 DR Sheet 13 Metal, welded, four-lead crystal unit outline
14 DZ Sheet 14 Metal, welded, two-lead crystal unit outline
Metal, solder-diffusion-sealed, two-lead cylindrical crystal unit
15 DV Sheet 15
outline
60122-3 © IEC:2001 – 17 –
Table 1 – Designation of quartz crystal unit enclosures (continued
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.