EN 61215-1-3:2017
(Main)Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-3: Special requirements for testing of thin-film amorphous silicon based photovoltaic (PV) modules
Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-3: Special requirements for testing of thin-film amorphous silicon based photovoltaic (PV) modules
IEC 61215-1-3:2016 lays down requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open-air climates, as defined in IEC 60721-2-1. This document is intended to apply to all thin-film amorphous silicon (a-Si; a-Si/µc-Si) based terrestrial flat plate modules. As such, it addresses special requirements for testing of this technology supplementing IEC 61215-1:2016 and IEC 61215-2:2016 requirements for testing.
Terrestrische kristalline Silizium-Photovoltaik(PV)-Module - Bauarteignung und Bauartzulassung - Teil 1-3: Besondere Anforderungen an die Prüfung von Photovoltaik(PV)-Dünnschichtmodulen aus amorphem Silizium
Modules photovoltaïques (PV) pour applications terrestres - Qualification de la conception et homologation - Partie 1-3: Exigences particulières d'essai des modules photovoltaïques (PV) au silicium amorphe à couches minces
L'IEC 61215-1-3:2016 établit les exigences pour la qualification de la conception et l'homologation des modules photovoltaïques (PV) pour applications terrestres et pour une utilisation de longue durée dans les grandes zones climatiques à l'air libre, telles qu'elles sont définies dans l'IEC 60721-2-1. Le présent document est destiné à s'appliquer à tous les modules à plaque plane au silicium amorphe (a-Si; a-Si/µc-Si) à couches minces pour applications terrestres. A ce titre, il spécifie des exigences d'essai particulières à cette technologie en complément des exigences d'essai données dans l'IEC 61215-1:2016 et l'IEC 61215-2:2016.
Prizemni fotonapetostni (PV) moduli - Ocena zasnove in odobritev tipa - 1-3. del: Posebne zahteve za preskušanje fotonapetostnih modulov iz tankoslojnega amorfnega silicija
Ta del standarda IEC 61215 določa zahteve IEC glede ocene zasnove in tipske odobritve prizemnih fotonapetostnih modulov, primernih za dolgotrajno uporabo v običajnih okoljih na prostem, kot je opredeljeno v standardu IEC 60721-2-1. Ta dokument je namenjen za uporabo za vse ploščate prizemne module iz tankoslojnega amorfnega silicija (a-Si; a-Si/μc-Si). Kot tak obravnava posebne zahteve za preskušanje te tehnologije, ki dopolnjujejo zahteve za preskušanje iz standardov IEC 61215-1:2016 in IEC 61215-2:2016.
Ta dokument se ne uporablja za module za uporabo s koncentrirano sončno svetlobo, lahko pa se uporablja za nizkokoncentracijske module (1 do 3 sončni viri). Za nizkokoncentracijske module se vsi preskusi izvedejo s tokovno, napetostno in močnostno ravnjo, ki so pričakovane pri načrtovani koncentraciji.
Namen tega preskusnega zaporedja je določiti električne in toplotne lastnosti modula ter prikazati (kot je mogoče v razumnih stroškovnih in časovnih omejitvah), da je modul zmožen prenesti učinke dolgotrajne izpostavljenosti v okoljih, opisanih v razdelku z opredeljenim področjem uporabe. Dejanska pričakovana življenjska doba tako kvalificiranih modulov je odvisna od njihove zasnove, okolja uporabe in pogojev delovanja.
Ta dokument določa spremembe preskusnih postopkov in zahtev v skladu s standardoma IEC 61215-1:2016 in IEC 61215-2:2016, ki so odvisne od prizemne fotonapetostne tehnologije.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2017
1DGRPHãþD
SIST EN 61646:2008
Prizemni fotonapetostni (PV) moduli - Ocena zasnove in odobritev tipa - 1-3. del:
Posebne zahteve za preskušanje fotonapetostnih modulov iz tankoslojnega
amorfnega silicija
Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-3:
Special requirements for testing of thin-film amorphous silicon based photovoltaic (PV)
modules
Terrestrische kristalline Silizium-Photovoltaik-(PV)-Module - Bauarteignung und
Bauartzulassung - Teil 1-3: Besondere Anforderungen für Prüfungen von Photovoltaik-
(PV)-Modulen aus amorphem Silizium
Modules photovoltaïques (PV) pour applications terrestres - Qualification de la
conception et homologation - Partie 1-3: Exigences particulières d'essai des modules
photovoltaïques (PV) au silicium amorphe à couches minces
Ta slovenski standard je istoveten z: EN 61215-1-3:2017
ICS:
27.160 6RQþQDHQHUJLMD Solar energy engineering
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 61215-1-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2017
ICS 27.160 Supersedes EN 61646:2008
English Version
Terrestrial photovoltaic (PV) modules - Design qualification and
type approval - Part 1-3: Special requirements for testing of thin-
film amorphous silicon based photovoltaic (PV) modules
(IEC 61215-1-3:2016)
Modules photovoltaïques (PV) pour applications terrestres - Terrestrische kristalline Silizium-Photovoltaik-(PV)-Module -
Qualification de la conception et homologation - Bauarteignung und Bauartzulassung -
Partie 1-3: Exigences particulières d'essai des modules Teil 1-3: Besondere Anforderungen für Prüfungen von
photovoltaïques (PV) au silicium amorphe à couches Photovoltaik-(PV)-Modulen aus amorphem Silizium
minces (IEC 61215-1-3:2016)
(IEC 61215-1-3:2016)
This European Standard was approved by CENELEC on 2017-01-11. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61215-1-3:2017 E
European foreword
The text of document 82/1183/FDIS, future edition 1 of IEC 61215-1-3, prepared by IEC/TC 82 "Solar
photovoltaic energy systems" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 61215-1-3:2017.
The following dates are fixed:
(dop) 2017-11-05
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2020-05-05
• latest date by which the national standards conflicting with
the document have to be withdrawn
This document supersedes EN 61646:2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61215-1-3:2016 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
Annexes ZA of EN 61215-1:2016 and EN 61215-2:2017 are applicable.
IEC 61215-1-3 ®
Edition 1.0 2016-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Terrestrial photovoltaic (PV) modules – Design qualification and type approval –
Part 1-3: Special requirements for testing of thin-film amorphous silicon based
photovoltaic (PV) modules
Modules photovoltaïques (PV) pour applications terrestres – Qualification de la
conception et homologation –
Partie 1-3: Exigences particulières d'essai des modules photovoltaïques (PV) au
silicium amorphe à couches minces
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 27.160 ISBN 978-2-8322-3785-4
– 2 – IEC 61215-1-3:2016 © IEC 2016
CONTENTS
FOREWORD . 3
1 Scope and object . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Test samples . 5
5 Marking and documentation . 5
6 Testing . 5
7 Pass criteria . 6
8 Major visual defects . 6
9 Report . 6
10 Modifications . 6
11 Test flow and procedures . 6
11.1 Visual inspection (MQT 01) . 6
11.2 Maximum power determination (MQT 02) . 6
11.3 Insulation test (MQT 03) . 6
11.4 Measurement of temperature coefficients (MQT 04) . 6
11.5 Measurement of nominal module operating temperature (NMOT) (MQT 05) . 6
11.6 Performance at STC (MQT 06.1) and NMOT (MQT 06.2) . 6
11.7 Performance at low irradiance (MQT 07) . 6
11.8 Outdoor exposure test (MQT 08) . 7
11.9 Hot-spot endurance test (MQT 09). 7
11.9.1 Purpose . 7
11.9.2 Hot-spot effect . 7
11.9.3 Classification of cell interconnection . 7
11.9.4 Apparatus . 7
11.9.5 Procedure . 7
11.9.6 Final measurements . 7
11.9.7 Requirements . 7
11.10 UV preconditioning test (MQT 10) . 7
11.11 Thermal cycling test (MQT 11) . 7
11.12 Humidity-freeze test (MQT 12) . 7
11.13 Damp heat test (MQT 13) . 7
11.14 Robustness of terminations test (MQT 14) . 8
11.15 Wet leakage current test (MQT 15) . 8
11.16 Static mechanical load test (MQT 16) . 8
11.17 Hail test (MQT 17) . 8
11.18 Bypass diode testing (MQT 18) . 8
11.19 Stabilization (MQT 19) . 8
11.19.2 Criterion definition for stabilization . 8
11.19.3 Light induced stabilization procedure . 8
11.19.4 Other stabilization procedures . 8
11.19.5 Initial stabilization (MQT 19.1) . 9
11.19.6 Final stabilization (MQT 19.2) . 9
IEC 61215-1-3:2016 © IEC 2016 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
TERRESTRIAL PHOTOVOLTAIC (PV) MODULES –
DESIGN QUALIFICATION AND TYPE APPROVAL –
Part 1-3: Special requirements for testing of thin-film
amorphous silicon based photovoltaic (PV) modules
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable fo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.