EN 50632-2-1:2015

Electric motor-operated tools - Dust measurement procedure - Part 2-1: Particular requirements for diamond core drills

This clause of Part 1 is applicable except as follows: Addition: This part of EN 50632 applies to diamond core drills.

Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-1: Besondere Anforderungen für Diamantkernbohrmaschinen

Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-1: Exigences particulières pour les perceuses et les perceuses à percussion

Elektromotorna orodja - Postopek meritve prahu - 2-1. del: Posebne zahteve za svedre in udarne svedre

Ta evropski standard določa splošne zahteve za meritve prahu elektromotornih orodij, ki se napajajo iz omrežja ali baterij. Ta evropski standard velja za tista orodja, pri katerih se pričakuje nabiranje prahu (na primer mineralnega prahu, ki vsebuje kremenico, ali lesnega prahu), ne glede na to, ali so opremljeni z enoto za izločevanje prahu ali ne.

General Information

• Status: Published
• Publication Date: 20-Aug-2015
• Withdrawal Date: 02-Aug-2017
• ICS: 25.140.20 - Electric tools
• Technical Committee: CLC/TC 116 - Safety of hand-held motor-operated electric tools
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 19-Jan-2020
• Ref Project: SIST EN 50632-2-1:2015 - Electric motor-operated tools - Dust measurement procedure - Part 2-1: Particular requirements for drills and impact drills

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2015
Elektromotorna orodja - Postopek meritve prahu - 2-1. del: Posebne zahteve za
svedre in udarne svedre
Electric motor-operated tools - Dust measurement procedure - Part 2-1: Particular
requirements for drills and impact drills
Ta slovenski standard je istoveten z: EN 50632-2-1:2015
ICS:
25.100.30 Svedri, greznila, posnemalna Drills, countersinks, reamers
orodja
25.140.20 (OHNWULþQDRURGMD Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50632-2-1

NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2015
ICS 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-1: Particular requirements for diamond core drills
Outils électriques à moteur - Mode opératoire pour la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
mesure de la poussière - Partie 2-1: Exigences particulières Teil 2-1: Besondere Anforderungen für Diamant-
pour les perceuses et les perceuses à percussion Kernbohrmaschinen
This European Standard was approved by CENELEC on 2015-08-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-1:2015 E
Contents
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test procedure . 4
5 Instrumentation . 5
6 Information to be reported . 5
Figures
Figure 101 – A-support . 6
Figure 102 – Test set-up . 7
Tables
Table 101 — Operating conditions for diamond core drills . 5

European foreword
This document (EN 50632-2-1:2015) has been prepared by CLC/TC 116 “Safety of motor-operated
electric tools”.
The following dates are fixed:

(dop) 2016-08-03
• latest date by which this document has to be
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2017-08-03
conflicting with this document have to
be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held respon
...