CLC/TS 50131-2-6:2004
(Main)Alarm systems - Intrusion systems - Part 2-6: Requirements for opening contacts (magnetic)
Alarm systems - Intrusion systems - Part 2-6: Requirements for opening contacts (magnetic)
Interim TS before EN status (procedure to begin in 2006) * D117/092: Standstill maintained * Superseded by EN 50131-2-6:2008
Alarmanlagen - Einbruchmeldeanlagen - Teil 2-6: Anforderungen an Öffnungsmelder (Magnetkontakte)
Systèmes d'alarme - Systèmes d'alarme intrusion - Partie 2-6: Exigences pour contacts magnétiques
Alarmni sistemi – Sistemi za javljanje vloma – 2-6. del: Zahteve za kontaktne javljalnike (magnetne)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2005
Alarmni sistemi – Sistemi za javljanje vloma – 2-6. del: Zahteve za kontaktne
javljalnike (magnetne)
Alarm systems - Intrusion systems -- Part 2-6: Requirements for opening contacts
(magnetic)
Alarmanlagen - Einbruchmeldeanlagen -- Teil 2-6: Anforderungen an Öffnungsmelder
(Magnetkontakte)
Systèmes d'alarme - Systèmes d'alarme intrusion -- Partie 2-6: Exigences pour contacts
magnétiques
Ta slovenski standard je istoveten z: CLC/TS 50131-2-6:2004
ICS:
13.310 Varstvo pred kriminalom Protection against crime
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL SPECIFICATION CLC/TS 50131-2-6
SPECIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION August 2004
ICS 13.310
English version
Alarm systems - Intrusion systems
Part 2-6: Requirements for opening contacts (magnetic)
Systèmes d'alarme - Alarmanlagen -
Systèmes de détection d'intrusion Einbruchmeldeanlagen
Partie 2-6: Exigences pour contacts Teil 2-6: Anforderungen an
magnétiques Öffnungsmelder (Magnetkontakte)
This Technical Specification was approved by CENELEC on 2004-05-04.
CENELEC members are required to announce the existence of this TS in the same way as for an EN and to
make the TS available promptly at national level in an appropriate form. It is permissible to keep conflicting
national standards in force.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. CLC/TS 50131-2-6:2004 E
Foreword
This Technical Specification was prepared by the Technical Committee CENELEC TC 79, Alarm systems.
The text of the draft was submitted to the vote at the meeting of TC 79 in Madrid and was approved by
CENELEC as CLC/TS 50131-2-6 on 2004-05-04. Standstill is maintained.
The following date was fixed:
- latest date by which the existence of the TS (doa) 2004-11-04
has to be announced at national level
NOTE Latest date by which the TS has to be voted as EN: 2 years maximum after dav of TS.
- 3 - CLC/TS 50131-2-6:2004
Contents
Page
1 Scope.4
2 Normative references.4
3 Definitions and abbreviations .4
4 Functional requirements.5
4.1 Indication signals or messages .5
4.2 Detection .6
4.3 Operational requirements.6
4.4 Tamper security.7
4.5 Electrical requirements.8
4.6 Environmental classification and conditions.8
5 Marking, identification and documentation .9
5.1 Marking and/or identification .9
5.2 Documentation .9
6 Testing.9
6.1 General test conditions.9
6.2 Basic test of detection capability .10
6.3 Verification of detection performance.10
6.4 Switch-on delay, time interval between signals and indication of detection .10
6.5 Tamper security.10
6.6 Electrical tests .11
6.7 Environmental classification and conditions.12
6.8 Marking and documentation.13
Annex A (normative) Format of standard test magnets.15
Annex B (normative) General test matrix .16
Annex C (informative) List of small tools suitable for testing immunity of casing to attack .17
Figure A.1 - Format of standard test magnets.14
Table 1 – Indication signals or messages .6
Table 2 - Tamper security requirements.7
Table 3 - Electrical requirements.8
Table 4 - Environmental tests, operational. .13
Table 5 - Environmental tests, endurance.13
Introduction
This Technical Specification is a specification for opening contacts (magnetic) used as part of intrusion
detection systems installed in buildings. It provides for four security grades and the first three
environmental classes.
The purpose of an opening contact (magnetic) is to detect a displacement of a door or window from a
closed position. A signal or message is generated when the detector registers a displacement of the door
or window from the closed position. The detector shall provide the necessary range of signals or
messages to be used by the rest of the intrusion detection system.
This specification is only concerned with the requirements and tests for opening contacts (magnetic).
Other types of detector are covered by other documents identified as CLC/TS 50131-2-x.
1 Scope
This Technical Specification provides for security grades 1 to 4 (see EN 50131-1) specific or non-specific
wired or wire-free opening contacts (magnetic), and is covered by environmental classes I to III (see
EN 50130-5).
A function designated in the specification as not required for a particular grade may be provided by the
manufacturer. If provided, it will be tested, and shall meet all relevant requirements of any higher grade. If
it passes, the manufacturer may claim it as an extra feature, which does not alter the overall grading.
The opening contact (magnetic) shall be referred to in the body of this specification as the detector.
This specification does not apply to system interconnections.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 50130-4:1995 Alarm systems - Part 4: Electromagnetic compatibility - Product family standard:
Immunity requirements for components of fire, intruder and socialalarm systems
EN 50130-5:1998 Alarm systems - Part 5: Environmental test methods
EN 50131-1:1997 Alarm Systems – Intrusion systems - Part 1: General requirements
EN 50131-6:1997 Alarm systems - Intrusion systems - Part 6: Power supplies
EN 60529:1991 Degree of protection provided by enclosures (IP code)
3 Definitions and abbreviations
For the purpose of this specification. the following definitions and abbreviations apply in addition to those
given in EN 50131-1:
3.1
alert/set mode
state of operation in which a detector is ready to generate an intrusion signal or message
3.2
approach distance/make distance
the separation distance between the two components of a detector, which are being brought together, at
which an intruder signal or message is reset
- 5 - CLC/TS 50131-2-6:2004
3.3
incorrect operation
physical condition that causes an inappropriate signal from a detector
3.4
magnetic masking
interference with the capability of the detector to provide a signal or message by applying an additional
magnetic field
3.5
opening contact (magnetic)
detector in two separate parts. The active connection between the two parts is a magnetic field.
Separating the two parts disturbs the connection and produces an intruder signal or message
3.6
removal distance/break distance
the separation distance between the two components of a detector, which are being moved apart, at
which an intruder signal or message starts to be generated
3.7
reset signal
signal or message generated by a detector to indicate that it has returned to the alert/set mode
3.8
standby/unset mode
state of operation in which a detector is not required to generate an intrusion signal or message
3.9
test mode
state of operation in which a detector will indicate locally or remotely when the door or window is opened
3.10
wire free detector
detector connected to the control & indicating equipment by non-physical means such as radio frequency
signals
3.11 abbreviations
EMC electromagnetic compatibility
BDT basic detection target
4 Functional requirements
4.1 Indication signals or messages
All detectors shall have an alert/set mode. If a detector has only one mode of operation, then it shall
always be in the alert/set mode. Tamper detection for grade 1 is not required, but if provided, shall be
active in all modes. Sealed units do not require a tamper switch but shall have a tamper loop or equivalent
connected to the detector. Each possible mode of operation is determined by the status of the intrusion
detection system with which the detector communicates. The detector signals or messages shall function
in accordance with Table 1.
Table 1 – Indication signals or messages
Event Grades Intrusion signal or Tamper signal or Fault signal or
message message message
Break distance exceeded All grades Required * Not permitted Not permitted
Inside make distance All grades Not permitted Not permitted Not permitted
1,2 Not required Not required Not required
Magnetic interference
3 & 4 Not required Required Not required
Tamper 2, 3 & 4 Not permitted Required + Not permitted
Low supply voltage (external) *** 1, 2 & 3 Not required Not required Not required
4 Not required Not required Required
1, 2 & 3 Not required Not required Not required
Total loss of external power
supply ***
4 Required ** Not required Not required
* Not required in unset/standby mode: required in test mode.
** Not required for bus systems.
*** Where external power is required.
+ Not required for sealed contacts.
NOTE For internal power supplies, see EN 50131-6.
4.2 Detection
4.2.1 Detection performance
The operating parameters of the detector shall be verified as specified by the manufacturer.
4.2.1.1 Removal/break distance
The detector shall produce an Intruder signal or message at the separation distance specified by the
manufacturer. The removal/break distance shall be verified.
4.2.1.2 Approach/make distance
The detector shall produce a reset signal or message at the separation distance specified by the
manufacturer. The approach/make distance shall be verified.
4.2.2 Indication of detection
An indicator, if provided at the detector, shall indicate when detection causes an intrusion signal or
message. This indicator shall be capable of being enabled/disabled. This operation shall only be
performed locally after removal of the cover or remotely at the control and indicating equipment.
4.3 Operational requirements
4.3.1 Time interval between intrusion signals or messages
Wired detectors shall be able to provide an intrusion signal or message not more than 15 s after the end
of the preceding intrusion signal or message. Wire free detectors shall perform the same function in a
time as follows:
Grade 1: 300 s
Grade 2: 300 s
Grade 3: 15 s
Grade 4: 15 s
NOTE See EN 50131-1 for amendment.
- 7 - CLC/TS 50131-2-6:2004
4.3.2 Switch on delay
The detector shall meet all funct
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.