EN IEC/IEEE 62209-1528:2021/prA1:2025
(Amendment)Amendment 1 - Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-worn wireless communication devices - Human models, instrumentation and procedures (Frequency range of 4 MHz to 10 GHz)
Amendment 1 - Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-worn wireless communication devices - Human models, instrumentation and procedures (Frequency range of 4 MHz to 10 GHz)
Procédure de mesure pour l'évaluation du débit d'absorption spécifique de l'exposition humaine aux champs radiofréquence produits par les dispositifs de communications sans fil tenus à la main ou portés près du corps - Partie 1528: Modèles humains, instrumentation et procédures (plage de fréquences comprise entre 4 MHz et 10 GHz)
Merilni postopki za ocenjevanje stopnje specifične absorpcije pri izpostavljenosti ljudi elektromagnetnim sevanjem brezžičnih komunikacijskih naprav, ki se držijo v roki ali pritrdijo na telo - 1528. del: Človeški modeli, instrumenti in postopki (frekvenčno območje od 4 MHz do 10 GHz) - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC/IEEE 62209-
1528:2022/oprA1:2025
01-april-2025
Merilni postopki za ocenjevanje stopnje specifične absorpcije pri izpostavljenosti
ljudi elektromagnetnim sevanjem brezžičnih komunikacijskih naprav, ki se držijo v
roki ali pritrdijo na telo - 1528. del: Človeški modeli, instrumenti in postopki
(frekvenčno območje od 4 MHz do 10 GHz) - Dopolnilo A1
Amendment 1 - Measurement procedure for the assessment of specific absorption rate
of human exposure to radio frequency fields from hand-held and body-worn wireless
communication devices - Human models, instrumentation and procedures (Frequency
range of 4 MHz to 10 GHz)
Procédure de mesure pour l'évaluation du débit d'absorption spécifique de l'exposition
humaine aux champs radiofréquence produits par les dispositifs de communications
sans fil tenus à la main ou portés près du corps - Partie 1528: Modèles humains,
instrumentation et procédures (plage de fréquences comprise entre 4 MHz et 10 GHz)
Ta slovenski standard je istoveten z: EN IEC/IEEE 62209-1528:2021/prA1:2025
ICS:
13.280 Varstvo pred sevanjem Radiation protection
33.050.10 Telefonska oprema Telephone equipment
SIST EN IEC/IEEE 62209- en
1528:2022/oprA1:2025
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
106/686/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC/IEEE 62209-1528/AMD1 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2025-02-07 2025-05-02
SUPERSEDES DOCUMENTS:
106/629B/RR
IEC TC 106 : METHODS FOR THE ASSESSMENT OF ELECTRIC, MAGNETIC AND ELECTROMAGNETIC FIELDS ASSOCIATED
WITH HUMAN EXPOSURE
SECRETARIAT: SECRETARY:
Germany Mr Alexander Prokop
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
TC 9,TC 27,TC 29,TC 34,SC 62A,SC 62B,TC 69,TC
77,TC 79,TC 96,TC 100,TC 124,CISPR
ASPECTS CONCERNED:
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Amendment 1 - Measurement procedure for the assessment of specific absorption rate of
human exposure to radio frequency fields from hand-held and body-worn wireless
communication devices - Human models, instrumentation and procedures (Frequency range of
4 MHz to 10 GHz)
PROPOSED STABILITY DATE: 2027
NOTE FROM TC/SC OFFICERS:
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
IEC/IEEE CDV 62209-1528/AMD1 ED1 © IEC/IEEE 2025 106/686/CD
1 CONTENTS
3 FOREWORD . 3
4 INTRODUCTION to the (CD,CDV) (not to be included in final publication) . 5
5 7 Protocol for SAR assessment . 6
6 7.2 Measurement preparation . 6
7 7.2.4 Positioning of the DUT relative to the phantom . 6
8 7.6 Time-period averaged SAR . 7
9 7.6.1 General . 7
10 7.6.2 Exposure conditions and test positions . 8
11 7.6.3 SAR measurements . 8
12 7.6.4 Time-period averaged SAR for simultaneous transmission . 10
13 7.7 Proximity sensors considerations . 11
14 7.7.1 General . 11
15 7.7.2 Procedures for determining proximity sensor triggering distances . 11
16 7.9 Minimization of testing time . 12
17 7.9.3 SAR test reductions . 12
18 7.10 Motion sensors considerations . 13
19 7.10.1 General . 13
20 7.10.2 SAR measurement procedure involving motion sensors . 14
21 7.11 Devices used next to the ear during voice calls . 15
22 7.11.1 General . 15
23 7.11.2 Scope . 16
24 7.11.3 Applicability criteria . 16
25 7.11.4 Hand SAR test procedure . 17
26 7.11.5 Duty cycle considerations for hand SAR testing . 17
27 Annex X (informative) Rationale for head phantom test reductions based on flat
28 phantom SAR data . 20
29 X.1 General . 20
30 X.2 Rationale for SAR level threshold . 20
31 X.3 Rationale for distance threshold . 21
32 Annex Y (normative) Validation of motion sensors . 23
33 Y.1 General . 23
34 Y.2 Procedure . 23
35 Y.3 Validation report . 25
36 Bibliography . 26
38 Figure 29 – Illustration of the output power characteristics of a simple TPAS
39 implementation . 9
40 Figure X.1 – Number of test cases where the psSAR at a specified distance to the flat
41 phantom is more than 5 % higher than the psSAR at d = 0 mm, and the psSAR is at
42 least 0,2 W/kg . 21
43 Figure X.2 – Distance along a representation of a planar DUT between the ERP and a
44 point that is 10 mm from the SAM phantom outer shell. 22
45 Figure Y.1 –Procedure for the validation of the power reduction . 24
IEC/IEEE CDV 62209-1528/AMD1 ED1 © IEC/IEEE 2025 106/686/CD
48 INTERNATIONAL ELECTROTECHNICAL COMMISSION
49 ____________
51 MEASUREMENT PROCEDURE FOR THE ASSESSMENT OF SPECIFIC
52 ABSORPTION RATE OF HUMAN EXPOSURE TO RADIO FREQUENCY
53 FIELDS FROM HAND-HELD AND BODY-MOUNTED WIRELESS
54 COMMUNICATION DEVICES –
56 Part 1528: Human models, instrumentation, and procedures
57 (Frequency range of 4 MHz to 10 GHz)
59 AMENDMENT 1
61 FOREWORD
62 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
63 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
64 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
65 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
66 Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC document(s)"). Their
67 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
68 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
69 with the IEC also participate in this preparation.
70 IEEE Standards documents are developed within IEEE Societies and Standards Coordinating Committees of the
71 IEEE Standards Association (IEEE SA) Standards Board. IEEE develops its standards through a consensus
72 development process, approved by the American National Standards Institute, which brings together volunteers
73 representing varied viewpoints and interests to achieve the final product. Volunteers are not necessarily members
74 of IEEE and serve without compensation. While IEEE administers the process and establishes rules to promote
75 fairness in the consensus development process, IEEE does not independently evaluate, test, or verify the
76 accuracy of any of the information contained in its standards. Use of IEEE Standards documents is wholly
77 voluntary. IEEE documents are made available for use subject to important notices and legal disclaimers (see
78 https://standards.ieee.org/ipr/disclaimers.html for more information).
79 IEC collaborates closely with IEEE in accordance with conditions determined by agreement between the two
80 organizations. This Dual Logo International Standard was jointly developed by the IEC and IEEE under the terms
81 of that agreement.
82 2) The formal decisions of IEC on technical matters express, as nearly as possible, an international consensus of
83 opinion on the relevant subjects since each technical committee has representation from all interested IEC
84 National Committees. The formal decisions of IEEE on technical matters, once consensus within IEEE Societies
85 and Standards Coordinating Committees has been reached, is determined by a balanced ballot of materially
86 interested parties who indicate interest in reviewing the proposed standard. Final approval of the IEEE standards
87 document is given by the IEEE Standards Association (IEEE SA) Standards Board.
88 3) IEC/IEEE Publications have the form of recommendations for international use and are accepted by IEC National
89 Committees/IEEE Societies in that sense. While all reasonable efforts are made to ensure that the technical
90 content of IEC/IEEE Publications is accurate, IEC or IEEE cannot be held responsible for the way in which they
91 are used or for any misinterpretation by any end user.
92 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
93 (including IEC/IEEE Publications) transparently to the maximum extent possible in their national and regional
94 publications. Any divergence between any IEC/IEEE Publication and the corresponding national or regional
95 publication shall be clearly indicated in the latter.
96 5) IEC and IEEE do not provide any attestation of conformity. Independent certification bodies provide conformity
97 assessment services and, in some areas, access to IEC marks of conformity. IEC and IEEE are not responsible
98 for any services carried out by independent certification bodies.
99 6) All users should ensure that they have the latest edition of this publication.
100 7) No liability shall attach to IEC or IEEE or their directors, employees, servants or agents including individual
101 experts and members of technical committees and IEC National Committees, or volunteers of IEEE Societies and
102 the Standards Coordinating Committees of the IEEE Standards Association (IEEE SA) Standards Board, for any
103 personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for
104 costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC/IEEE
105 Publication or any other IEC or IEEE Publications.
106 8) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is
107 indispensable for the correct application of this publication.
IEC/IEEE CDV 62209-1528/AMD1 ED1 © IEC/IEEE 2025 106/686/CD
108 9) Attention is drawn to the possibility that implementation of this IEC/IEEE Publication may require use of material
109 covered by patent rights. By publication of this standard, no position is taken with respect to the existence or
110 validity of any patent rights in connection therewith. IEC or IEEE shall not be held responsible for identifying
111 Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or
112 scope of Patent Claims or determining whether any licensing terms or conditions provided in connection with
113 submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory.
114 Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk
115 of infringe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.