Abstract

This part of IEC 61300 describes a test to quantitatively assess the capability of a connector terminating a reinforced cable of any diameter or a buffered fibre, both single-mode and multimode, to withstand static loads without uncoupling of the connector, physical damage to the assembly or permanent degradation of optical performance.

Status
Published
Publication Date
12-Nov-2026
Current Stage
6060 - Document made available - Publishing
Start Date
13-Nov-2026
Due Date
30-Jun-2026
Completion Date
13-Nov-2026

Buy Documents

Standard

EN IEC 61300-2-50:2027

English language (14 pages)
Preview
Preview
e-Library read for
×1 day

EN IEC 61300-2-50:2026 is a test standard for fibre optic connector proof testing with static load. It specifies how to assess whether a connector terminated to a reinforced cable or a buffered fibre can withstand static pulling loads without uncoupling, physical damage, or permanent degradation of optical performance.

What does EN IEC 61300-2-50:2026 specify?

EN IEC 61300-2-50:2026 specifies a proof test for fibre optic connectors under static load and is written for single-mode and multimode connectors. The document is organized into clauses for scope, normative references, terms and definitions, apparatus, test setup, procedure, severity, and reporting, with figures showing the test arrangement and load application.

The test is intended to reflect abrupt mechanical stress that can happen during installation and maintenance. In practice, that means the document tells users how to set up the connector, apply the load in defined directions, check optical performance before and after the load, and record the outcome.

What are the key requirements of EN IEC 61300-2-50:2026?

EN IEC 61300-2-50:2026 requires the device under test (DUT) to be examined, preconditioned, tested under a defined static load, and then remeasured for optical performance. The central idea is to compare the connector’s condition before and after loading and confirm that it still meets the relevant performance limits.

Test preparation and optical checks

Clause 7 requires visual examination of the DUT, cleaning of the mechanical and optical alignment parts, and inspection of the optical interfaces before the test. It also requires preconditioning for at least 2 h at standard atmospheric conditions, followed by initial measurements such as attenuation and return loss.

This matters because the starting condition becomes the reference for judging any change caused by the load.

Mounting and loading directions

Clause 7 distinguishes between straight pull and side pull configurations for the adaptor - plug - cable arrangement, and it also includes a pulling cap - plug - cable configuration for hardened connectors where applicable. The relevant performance standard or reliability document specifies whether straight pull, side pull, or both directions are required.

This matters because the connector may behave differently depending on how the force is applied, so the test must match the intended use case.

Load application and test setup

Clause 5 describes the apparatus, including the mounting fixture, mandrel, and force generator. The load must be applied smoothly, reach the required force within 20 s or less, and use a load rate suited to the cable type.

This matters because the test is designed to be repeatable and to avoid artificial shock loading that could distort the result.

Non-circular cables and hardened connectors

For non-circular cable forms such as ribbon or duplex cordage, the load is not doubled, and the cordage is bent in the minor-axis direction. For hardened connectors, the document adds a straight pull test in the pulling cap - plug - cable configuration, unless the design has no dedicated pulling cap for attaching the pulling gear.

This matters because special connector and cable constructions need special handling if the test is to remain realistic.

Final evaluation

Clause 7 requires final optical measurements after the load is removed, and the change from the initial values must remain within the limits set by the relevant performance or reliability document. The plug must stay connected until the final measurements are complete.

This matters because the test is not only about surviving the pull mechanically - it also checks whether optical performance stays acceptable.

Sealing and visual condition after test

After the load test, the DUT is visually examined for damage and, for hardened connectors, sealing checks are performed as specified. The document also lists likely failure modes such as broken parts, damaged strain relief elements, or uncoupling during the test.

This matters because a connector can fail mechanically even if it still appears to function optically, or vice versa.

What terms does EN IEC 61300-2-50:2026 define?

  • Device under test (DUT) - The connector assembly being evaluated in the proof test.
  • Pulling cap - A detachable component that protects the optical parts of the connector plug and can accept pulling gear.
  • Reinforced cable - The cable type used for one of the test applications described in the scope and procedure.
  • Buffered fibre - The fibre type covered by the scope when the connector is terminated to buffered fibre.
  • Hardened connectors - Connectors for which the procedure adds dedicated handling and sealing checks.
  • Performance category - The category used to link the test severity to the intended product performance level.

Who uses EN IEC 61300-2-50:2026?

EN IEC 61300-2-50:2026 is used by fibre optic connector designers, cable assembly manufacturers, test laboratories, and quality teams that qualify or verify connector robustness. It is also relevant to organizations working to IEC 61753 performance standards and IEC 62005 reliability documents, because those documents define the load, duration, and acceptance limits used with this test.

In practice, buyers and approval teams use it when they need a repeatable proof test for connector pull resistance and post-test optical stability.

What changed in EN IEC 61300-2-50:2026 from the previous edition?

EN IEC 61300-2-50:2026 cancels and replaces the first edition published in 2007 and is described as a technical revision. The document states these significant changes:

  • a normative references clause was added;
  • a terms and definitions clause was added;
  • a straight pull test for the pulling cap - plug - cable configuration was added;
  • the procedure was modified, including provisions for hardened connectors;
  • the severity was updated according to the component and performance category;
  • a details to be specified and reported clause was added.

Which standards are used with EN IEC 61300-2-50:2026?

EN IEC 61300-2-50:2026 depends on several IEC documents that define the supporting methods and the acceptance context:

  • IEC 60529 - used for ingress protection-related sealing checks.
  • IEC 61300-1 - gives general guidance and atmospheric conditioning.
  • IEC 61300-2-38 - provides the sealing test method used for sealed hardened connectors.
  • IEC 61300-3-1 - provides visual examination.
  • IEC 61300-3-3 - provides active optical measurement of attenuation and return loss.
  • IEC 61300-3-35 - provides visual inspection of fibre optic connectors and fibre-stub transceivers.
  • IEC 61753 (all parts) - provides performance standards that define the applicable limits and severities.
  • IEC 62005 (all parts) - provides reliability documents that also define applicable limits and severities.
  • IEC TR 62627-01 - gives cleaning methods for optical alignment parts.
  • IEC TS 63334 - supports sealing tests for passive optical protective housings and hardened fibre optic connectors.

What does the EN IEC 61300-2-50:2026 document contain?

EN IEC 61300-2-50:2026 contains a general description of the proof test, the apparatus needed, and the test setup shown in Figure 1. It also includes a second load application case for duplex cordage in Figure 2 and a severity table that links performance categories to load and duration.

The procedure covers preparation, preconditioning, initial optical measurements, mounting, straight pull testing, side pull testing, and final measurements. It also defines what must be reported, including DUT characteristics, mounting conditions, load application details, orientation, observed uncoupling or damage, severity, additional pass-fail criteria, and any deviations from the procedure.

Relations

Effective Date
13-Aug-2024
Effective Date
13-Aug-2024
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026

Buy Documents

Standard

EN IEC 61300-2-50:2027

English language (14 pages)
Preview
Preview
e-Library read for
×1 day

Get Certified

Connect with accredited certification bodies for this standard

ANCE

Mexican certification and testing association.

EMA Mexico Verified

Intertek Slovenia

Intertek testing, inspection, and certification services in Slovenia.

UKAS Slovenia Verified

LNE (Laboratoire National de Métrologie et d'Essais)

French national laboratory for metrology and testing.

COFRAC France Verified

Sponsored listings

Frequently Asked Questions

EN IEC 61300-2-50:2026 is a standard published by CLC. Its full title is "Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-50: Tests - Fibre optic connector proof test with static load". This standard covers: This part of IEC 61300 describes a test to quantitatively assess the capability of a connector terminating a reinforced cable of any diameter or a buffered fibre, both single-mode and multimode, to withstand static loads without uncoupling of the connector, physical damage to the assembly or permanent degradation of optical performance.

This part of IEC 61300 describes a test to quantitatively assess the capability of a connector terminating a reinforced cable of any diameter or a buffered fibre, both single-mode and multimode, to withstand static loads without uncoupling of the connector, physical damage to the assembly or permanent degradation of optical performance.

EN IEC 61300-2-50:2026 is classified under the following ICS (International Classification for Standards) categories: 33.180.20 - Fibre optic interconnecting devices. The ICS classification helps identify the subject area and facilitates finding related standards.

EN IEC 61300-2-50:2026 has the following relationships with other standards: It is inter standard links to EN 61300-2-50:2007, EN 61300-2-50:2007/AC:2015, EN 62005-4:1999, EN IEC 61300-1:2022, EN 62005-1:2001, EN IEC 61300-2-38:2023, EN 62005-3:2001, EN 62005-7:2004, EN IEC 61753-021-06:2023, EN 61300-3-1:2005, EN IEC 61753-021-02:2023, IEC TR 62627-01:2010, EN 61300-3-3:2009, EN IEC 61300-3-35:2022, EN 62005-2:2001. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN IEC 61300-2-50:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2027
Nadomešča:
SIST EN 61300-2-50:2007
SIST EN 61300-2-50:2007/AC:2015
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni
postopki - 2-50. del: Preskusi - Preskus preverjanja optičnih konektorjev s statično
obremenitvijo (IEC 61300-2-50:2026)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-50: Tests - Fibre optic connector proof test with static
load (IEC 61300-2-50:2026)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-50: Prüfungen - Festigkeitsprüfung für Lichtwellenleiter-
Steckverbinder (IEC 61300-2-50:2026)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes
fondamentales d'essais et de mesures - Partie 2-50: Essais - Essai de résistance des
connecteurs à fibres optiques sous charge statique (IEC 61300-2-50:2026)
Ta slovenski standard je istoveten z: EN IEC 61300-2-50:2026
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61300-2-50

NORME EUROPÉENNE
EUROPÄISCHE NORM November 2026
ICS 33.180.20 Supersedes EN 61300-2-50:2007; EN 61300-2-
50:2007/AC:2015
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-50: Tests -
Fibre optic connector proof test with static load
(IEC 61300-2-50:2026)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-
mesures - Partie 2-50: Essais - Essai de résistance des 50: Prüfungen - Festigkeitsprüfung für Lichtwellenleiter-
connecteurs fibroniques sous charge statique Steckverbinder
(IEC 61300-2-50:2026) (IEC 61300-2-50:2026)
This European Standard was approved by CENELEC on 2026-11-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61300-2-50:2026 E

European foreword
The text of document 86B/5246/FDIS, future edition 2 of IEC 61300-2-50, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61300-2-50:2026.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2027-11-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-11-30
document have to be withdrawn
This document supersedes EN 61300-2-50:2007 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61300-2-50:2026 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60529 - Degrees of protection provided by - -
enclosures (IP Code)
IEC 61300-1 - Fibre optic interconnecting devices and EN IEC 61300-1 -
passive components - Basic test and
measurement procedures - Part 1: General
and guidance
IEC 61300-2-38 2023 Fibre optic interconnecting devices and EN IEC 61300-2-38 2023
passive components - Basic test and
measurement procedures - Part 2-38:
Tests - Sealing for fibre optic sealed
closures and hardened connectors using
air pressure
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures - Part 3-1:
Examinations and measurements - Visual
examination
IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures - Part 3-3:
Examinations and measurements - Active
monitoring of changes in attenuation and
return loss
IEC 61300-3-35 - Fibre optic interconnecting devices and EN IEC 61300-3-35 -
passive components - Basic test and
measurement procedures - Part 3-35:
Examinations and measurements - Visual
inspection of fibre optic connectors and
fibre-stub transceivers
IEC 61753 series Fibre optic interconnecting devices and EN IEC 61753 series
passive components - Performance
standards
IEC 62005 series Reliability of fibre optic interconnecting EN 62005 series
devices and passive components
IEC/TR 62627-01 - Fibre optic interconnecting devices and - -
passive components - Part 01: Fibre optic
connector cleaning methods
IEC/TS 63334 - Fibre optic interconnecting devices and - -
passive components - Conditions for
testing the protection against dust and
water ingress of passive optical protective
housings and hardened fibre optic
connectors (IP5X, IPX4, IPX5, IPX6)

IEC 61300-2-50 ®
Edition 2.0 2026-09
INTERNATIONAL
STANDARD
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures -
Part 2-50: Tests - Fibre optic connector proof test with static load
ICS 33.180.20  ISBN 978-2-8327-1485-0

IEC 61300-2-50:2026-09(en)
IEC 61300-2-50:2026 © IEC 2026
CONTENTS
FOREWORD . 2
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 General description . 5
5 Apparatus . 5
5.1 General . 5
5.2 Mounting fixture . 5
5.3 Mandrel . 5
5.4 Force generator . 5
6 Test setup . 6
6.1 Fibre optic connector proof test with static load setup . 6
6.2 Optical measurement equipment . 7
7 Procedure . 7
7.1 Preparation of DUT . 7
7.2 Preconditioning . 7
7.3 Measure of initial optical properties . 7
7.4 Mounting of DUT . 7
7.5 Straight pull (pulling cap–plug–cable) . 8
7.6 Straight pull (adaptor–plug–cable) . 8
7.7 Side pull (adaptor–plug–cable) . 8
7.8 Final measurements and examinations . 8
8 Severity . 9
9 Details to be specified and reported . 9

Figure 1 – Fibre optic connector proof test with static load setup . 6
Figure 2 – Application of the load in the case of duplex cordage . 7

Table 1 – Test severities . 9

IEC 61300-2-50:2026 © IEC 2026
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 2-50: Tests - Fibre optic connector proof test with static load

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 61300-2-50 has been prepared by subcommittee 86B: Fibre optic interconnecting devices
and passive components, of IEC technical committee 86: Fibre optics. It is an International
Standard.
This second edition cancels and replaces the first edition published in 2007. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) addition of n
...