EN 61337-1:2004
(Main)Filters using waveguide type dielectric resonators - Part 1: Generic specification
Filters using waveguide type dielectric resonators - Part 1: Generic specification
Lists the test and measurement procedures which may be selected for use in detail specifications for filters using waveguide type dielectric resonators.
Filter mit dielektrischen Resonatoren vom Wellenleitertyp - Teil 1: Fachgrundspezifikation
Filtres utilisant des résonateurs diélectriques à modes guidés - Partie 1: Informations générales
Lists the test and measurement procedures which may be selected for use in detail specifications for filters using waveguide type dielectric resonators.
Filtri z dielektričnimi resonatorji valovodnega tipa – 1. del: Generična specifikacija (IEC 61337-1:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 61337-1:2005
STANDARD
december 2005
Filtri z dielektričnimi resonatorji valovodnega tipa – 1. del: Generična
specifikacija (IEC 61337-1:2004)
Filters using waveguide type dielectric resonators – Part 1: Generic specification
(IEC 61337-1:2004)
ICS 31.140; 31.160 Referenčna številka
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD EN 61337-1
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2004
ICS 31.140 Supersedes EN 171000:2001
English version
Filters using waveguide type dielectric resonators
Part 1: Generic specification
(IEC 61337-1:2004)
Filtres utilisant des résonateurs Filter mit dielektrischen Resonatoren
diélectriques à modes guidés vom Wellenleitertyp
Partie 1: Informations générales Teil 1: Fachgrundspezifikation
(CEI 61337-1:2004) (IEC 61337-1:2004)
This European Standard was approved by CENELEC on 2004-10-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61337-1:2004 E
Foreword
The text of document 49/685/FDIS, future edition 1 of IEC 61337-1, prepared by IEC TC 49,
Piezoelectric and dielectric devices for frequency control and selection, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61337-1 on 2004-10-01.
This European Standard supersedes EN 171000:2001.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2005-08-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2007-10-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61337-1:2004 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61337-1:2004
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60027 Series Letter symbols to be used in electrical HD 245 Series
technology HD 60027 Series
IEC 60050-561 1991 International Electrotechnical - -
Vocabulary (IEV)
Chapter 561: Piezoelectric devices for
frequency control and selection
1)
IEC 60068-1 1988 Environmental testing EN 60068-1 1994
Part 1: General and guidance
IEC 60068-2-1 1990 Part 2: Tests - Tests A: Cold EN 60068-2-1 1993
2)
IEC 60068-2-2 1974 Part 2: Tests - Tests B: Dry heat EN 60068-2-2 1993
IEC 60068-2-6 1995 Part 2: Tests - Test Fc: Vibration EN 60068-2-6 1995
(sinusoidal)
3)
IEC 60068-2-7 1983 Part 2: Tests - Test Ga: Acceleration, EN 60068-2-7 1993
steady state
IEC 60068-2-13 1983 Part 2: Tests - Test M: Low air EN 60068-2-13 1999
pressure
4)
IEC 60068-2-14 1984 Part 2: Tests - Test N: Change of EN 60068-2-14 1999
temperature
5)
IEC 60068-2-20 1979 Part 2: Tests - Test T: Soldering HD 323.2.20 S3 1988
IEC 60068-2-21 1999 Part 2-21: Tests - Test U: Robustness EN 60068-2-21 1999
of terminations and integral mounting
devices
1)
EN 60068-1 includes corrigendum October 1988 + A1:1992 to IEC 60068-1:1988.
2)
EN 60068-2-2 includes supplement A:1976 to IEC 60068-2-2:1974.
3)
EN 60068-2-7 includes A1:1986 to IEC 60068-2-7:1983.
4)
EN 60068-2-14 includes A1:1986 to IEC 60068-2-14:1984.
5)
HD 323.2.20 S3 includes A2:1987 to IEC 60068-2-20:1979.
Publication Year Title EN/HD Year
IEC 60068-2-27 1987 Part 2: Tests - Test Ea and guidance: EN 60068-2-27 1993
Shock
IEC 60068-2-29 1987 Part 2: Tests - Test Eb and guidance: EN 60068-2-29 1993
Bump
6)
IEC 60068-2-30 1980 Part 2: Tests - Test Db and guidance: EN 60068-2-30 1999
Damp heat, cyclic (12 + 12-hour cycle)
7)
IEC 60068-2-58 1999 Part 2-58: Tests - Test Td: Test EN 60068-2-58 1999
methods for solderability, resistance to
dissolution of metallization and to
soldering heat of surface mounting
devices (SMD)
IEC 60068-2-78 2001 Part 2-78: Tests - Test Cab: Damp EN 60068-2-78 2001
heat, steady state
IEC 60617 database Graphical symbols for diagrams - -
IEC QC 001002-2 1998 IEC Quality Assessment System for - -
Electronic Components (IECQ) -
Rules of Procedure
Part 2: Documentation
IEC QC 001001 2000 IEC Quality Assessment System for - -
Electronic Components (IECQ) - Basic
rules
IEC QC 001002-3 1998 IEC Quality Assessment System for - -
Electronic Components (IECQ) -
Rules of Procedure
Part 3: Approval procedures
IEC QC 001005 2000 Register of firms, products and - -
services approved under the IECQ
system, including ISO 9000
ISO 1000 1992 SI units and recommendations for the - -
use of their multiples and of certain
other units
6)
EN 60068-2-30 includes A1:1985 to IEC 60060-2-30:1980.
7)
EN 60068-2-58 is superseded by EN 60068-2-58:2004, which is based on IEC 60068-2-58:2004.
INTERNATIONAL IEC
STANDARD 61337-1
First edition
2004-11
Filters using waveguide type
dielectric resonators –
Part 1:
Generic specification
IEC 2004 Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale T
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue
– 2 – 61337-1 IEC:2004(E)
CONTENTS
FOREWORD.3
1 General .5
1.1 Scope.5
1.2 Normative references .5
1.3 Order of precedence .6
2 Terminology and general requirements.6
2.1 General .6
2.2 Terms and definitions .6
2.3 Preferred ratings and characteristics .13
2.4 Marking .14
3 Quality assessment procedures.14
3.1 Primary stage of manufacture.14
3.2 Structurally similar components.14
3.3 Sub-contracting .14
3.4 Incorporated components .14
3.5 Manufacturer’s approval .14
3.6 Approval procedures .14
3.7 Procedures for capability approval .15
3.8 Procedures for qualification approval.16
3.9 Test procedures .16
3.10 Screening requirements .16
3.11 Rework and repair work.16
3.12 Certified records of released lots.16
3.13 Validity of release.17
3.14 Release for delivery .17
3.15 Unchecked parameters.17
4 Test and measurement procedures.17
4.1 General .17
4.2 Test and measurement conditions .17
4.3 Visual inspection .18
4.4 Dimensions and gauging procedures .18
4.5 Electrical test procedures .18
4.6 Mechanical and environmental test procedures .22
Figure 1 – Equivalent circuit.7
Figure 2 – Typical frequency characteristics of a band-pass filter .10
Figure 3 – Typical frequency characteristics of a band-stop filter .11
Figure 4 – Insertion attenuation and group delay measurement .20
Figure 5 – Return attenuation measurement .20
61337-1 IEC:2004(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FILTERS USING WAVEGUIDE TYPE
DIELECTRIC RESONATORS –
Part 1: Generic specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.