IEC 61169-35:2011
(Main)Radio-frequency connectors - Part 35: Sectional specification for 2,92 series RF connectors
Radio-frequency connectors - Part 35: Sectional specification for 2,92 series RF connectors
IEC 61169-35:2011 provides information and rules for preparation of detail specification of 2,92 series RF coaxial connectors together with the pro-forma blank detail specification. It also prescribes mating face dimensions for high performance connectors - grade 1, dimensional detail of standard test connectors - Grade 0, gauging information and tests selected from IEC 61169-1 applicable to all detail specifications relating to 2,92 series RF coaxial connectors. It cancels and replaces IEC/PAS 61169-35, published in 2009, of which it constitutes a minor revision. The only change is that the PAS has been changed into and International Standard.
Connecteurs pour fréquences radioélectriques - Partie 35: Spécification intermédiaire pour les connecteurs RF série 2,92
La CEI 61169-35:2011 fournit des informations et des règles en vue de l'établissement de spécifications particulières de connecteurs coaxiaux RF de la série 2,92, ainsi que la spécification particulière cadre pro-forma. Elle prescrit également les dimensions des faces d'accouplement pour des connecteurs haute performance classe 1, des détails dimensionnels des connecteurs d essai normalisés. Classe 0, des informations de calibrage et des essais choisis dans la CEI 61169-1 applicable à toutes les spécifications particulières ayant trait aux connecteurs coaxiaux RF de la série 2,92. Cette édition annule et remplace la CEI/PAS 61169-35, publiée en 2009 dont elle constitue une révision mineure. Le seul changement consiste en la transformation de PAS en norme internationale.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 61169-35 ®
Edition 1.0 2011-07
INTERNATIONAL
STANDARD
colour
inside
Radio-frequency connectors –
Part 35: Sectional specification for 2,92 series RF connectors
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61169-35 ®
Edition 1.0 2011-07
INTERNATIONAL
STANDARD
colour
inside
Radio-frequency connectors –
Part 35: Sectional specification for 2,92 series RF connectors
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
T
ICS 33.120.30 ISBN 978-2-88912-559-3
– 2 – 61169-35 © IEC:2011(E)
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Mating face and gauge information . 6
3.1 Dimensions – High performance connectors – Grade 1 . 6
3.1.1 Connector with pin-centre contact . 6
3.1.2 Connector with socket-centre contact . 8
3.2 Gauges . 9
3.2.1 Gauge pins for socket-centre contact . 9
3.2.2 Test procedure . 9
3.3 Dimensions – standard test connectors – Grade 0 . 10
3.3.1 Connector with pin-centre contact . 10
3.3.2 Connector with socket-centre contact . 11
4 Quality assessment procedure . 11
4.1 General . 11
4.2 Rating and characteristics (see Clause 6 of IEC 61169-1) . 12
4.3 Test schedule and inspection requirements – Acceptance tests . 14
4.3.1 Acceptance tests . 14
4.3.2 Periodic tests . 15
4.4 Procedures . 16
4.4.1 Quality conformance inspection . 16
4.4.2 Qualification approval and its maintenance . 16
Instructions for preparation of detail specifications . 17
5.1 General . 17
5.2 Identification of the detail specification . 17
5.3 Identification of the component . 17
5.4 Performance . 17
5.5 Marking, ordering information and related matters . 18
5.6 Selection of tests, test conditions and severities . 18
5.7 Blank detail specification pro forma for 2,92 series connectors . 19
Bibliography . 24
Figure 1 – Connector with pin-centre contact (for dimensions and notes, see Table 1) . 7
Figure 2 – Connector with socket-centre contact (for dimensions and notes, see
Table 2) . 8
Figure 3 – Gauge pins for socket-centre contact (for dimensions and notes, see
Table 3) . 9
Figure 4 – Connector with pin-centre contact (for dimensions and notes, see Table 4) . 10
Figure 5 – Connector with socket-centre contact (for dimensions and notes, see
Table 5) . 11
61169-35 © IEC:2011(E) – 3 –
Table 1 – Dimensions of connector with pin-centre contact . 7
Table 2 – Dimensions of connector with socket-centre contact . 8
Table 3 – Dimensions of gauge pins for socket-centre contact . 9
Table 4 – Dimensions of connector with pin-centre contact . 10
Table 5 – Dimensions of connector with socket-centre contact . 11
Table 6 – Rating and characteristics . 12
Table 7 – Acceptance tests . 14
Table 8 – Periodic tests . 15
– 4 – 61169-35 © IEC:2011(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO-FREQUENCY CONNECTORS –
Part 35: Sectional specification for 2,92 series RF connectors
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-35 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides,
R.F. connectors, R.F. and microwave passive components and accessories.
This first edition cancels and replaces IEC/PAS 61169-35, published in 2009, of which it
constitutes a minor revision. The only change is that the PAS has been changed into and
International Standard.
The text of this standard is based on the following documents:
FDIS Report on voting
46F/191/FDIS 46F/196/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
61169-35 © IEC:2011(E) – 5 –
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors
can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this standard may be issued at a later date.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
– 6 – 61169-35 © IEC:2011(E)
RADIO-FREQUENCY CONNECTORS –
Part 35: Sectional specification for 2,92 series RF connectors
1 Scope
This sectional specification provides information and rules for preparation of detail
specification of 2,92 series RF coaxial connectors together with the pro-forma blank detail
specification.
It also prescribes mating face dimensions for high performance connectors - grade 1,
dimensional detail of standard test connectors - Grade 0, gauging information and tests
selected from IEC 61169-1 applicable to all detail specifications relating to 2,92 series RF
coaxial connectors.
This specification indicates recommended performance characteristics to be considered when
writing a detail specification and it covers test schedules and inspection requirements for
assessment levels M and H.
The 2,92 series coaxial connectors with characteristic impedance 50 Ω , 2,92 mm inner
diameter of outer conductor and screw coupling, are used for millimeter wave applications,
connecting with RF cables or microstrips. The operating frequency limit is up to 40 GHz.
Mating interface standards of the 2,92 series connectors are similar to IEEE std 287-2007
(2,92 mm) and MIL-std-348A (SMK). The 2,92 connectors can be inter-mated with S
...
IEC 61169-35 ®
Edition 1.0 2011-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio-frequency connectors –
Part 35: Sectional specification for 2,92 series RF connectors
Connecteurs pour fréquences radioélectriques –
Partie 35: Spécification intermédiaire pour les connecteurs RF série 2,92
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les
microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
Useful links:
IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org
The advanced search enables you to find IEC publications The world's leading online dictionary of electronic and
by a variety of criteria (reference number, text, technical electrical terms containing more than 30 000 terms and
committee,…). definitions in English and French, with equivalent terms in
It also gives information on projects, replaced and additional languages. Also known as the International
withdrawn publications. Electrotechnical Vocabulary (IEV) on-line.
IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc
Stay up to date on all new IEC publications. Just Published If you wish to give us your feedback on this publication
details all new publications released. Available on-line and or need further assistance, please contact the
also once a month by email. Customer Service Centre: csc@iec.ch.
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
Liens utiles:
Recherche de publications CEI - www.iec.ch/searchpub Electropedia - www.electropedia.org
La recherche avancée vous permet de trouver des Le premier dictionnaire en ligne au monde de termes
publications CEI en utilisant différents critères (numéro de électroniques et électriques. Il contient plus de 30 000
référence, texte, comité d’études,…). termes et définitions en anglais et en français, ainsi que
Elle donne aussi des informations sur les projets et les les termes équivalents dans les langues additionnelles.
publications remplacées ou retirées. Egalement appelé Vocabulaire Electrotechnique
International (VEI) en ligne.
Just Published CEI - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications de la CEI.
Just Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur
Disponible en ligne et aussi une fois par mois par email. cette publication ou si vous avez des questions
contactez-nous: csc@iec.ch.
IEC 61169-35 ®
Edition 1.0 2011-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio-frequency connectors –
Part 35: Sectional specification for 2,92 series RF connectors
Connecteurs pour fréquences radioélectriques –
Partie 35: Spécification intermédiaire pour les connecteurs RF série 2,92
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX T
ICS 33.120.30 ISBN 978-2-83220-666-9
– 2 – 61169-35 © IEC:2011
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Mating face and gauge information . 6
3.1 Dimensions – High performance connectors – Grade 1 . 6
3.1.1 Connector with pin-centre contact . 6
3.1.2 Connector with socket-centre contact . 8
3.2 Gauges . 9
3.2.1 Gauge pins for socket-centre contact . 9
3.2.2 Test procedure . 9
3.3 Dimensions – standard test connectors – Grade 0 . 10
3.3.1 Connector with pin-centre contact . 10
3.3.2 Connector with socket-centre contact . 11
4 Quality assessment procedure . 11
4.1 General . 11
4.2 Rating and characteristics (see Clause 6 of IEC 61169-1) . 12
4.3 Test schedule and inspection requirements – Acceptance tests . 14
4.3.1 Acceptance tests . 14
4.3.2 Periodic tests . 15
4.4 Procedures . 16
4.4.1 Quality conformance inspection . 16
4.4.2 Qualification approval and its maintenance . 16
Instructions for preparation of detail specifications . 17
5.1 General . 17
5.2 Identification of the detail specification . 17
5.3 Identification of the component . 17
5.4 Performance . 17
5.5 Marking, ordering information and related matters . 18
5.6 Selection of tests, test conditions and severities . 18
5.7 Blank detail specification pro forma for 2,92 series connectors . 19
Bibliography . 24
Figure 1 – Connector with pin-centre contact (for dimensions and notes, see Table 1) . 7
Figure 2 – Connector with socket-centre contact (for dimensions and notes, see
Table 2) . 8
Figure 3 – Gauge pins for socket-centre contact (for dimensions and notes, see
Table 3) . 9
Figure 4 – Connector with pin-centre contact (for dimensions and notes, see Table 4) . 10
Figure 5 – Connector with socket-centre contact (for dimensions and notes, see
Table 5) . 11
61169-35 © IEC:2011 – 3 –
Table 1 – Dimensions of connector with pin-centre contact . 7
Table 2 – Dimensions of connector with socket-centre contact . 8
Table 3 – Dimensions of gauge pins for socket-centre contact . 9
Table 4 – Dimensions of connector with pin-centre contact . 10
Table 5 – Dimensions of connector with socket-centre contact . 11
Table 6 – Rating and characteristics . 12
Table 7 – Acceptance tests . 14
Table 8 – Periodic tests . 15
– 4 – 61169-35 © IEC:2011
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO-FREQUENCY CONNECTORS –
Part 35: Sectional specification for 2,92 series RF connectors
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-35 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides,
R.F. connectors, R.F. and microwave passive comp
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.