IEC 60809:2014/AMD1:2017
(Amendment)Amendment 1 - Lamps for road vehicles - Dimensional, electrical and luminous requirements
Amendment 1 - Lamps for road vehicles - Dimensional, electrical and luminous requirements
The contents of the interpretation sheet 1 of July 2017 have been included in this copy.
Amendement 1 - Lampes pour véhicules routiers - Exigences dimensionnelles, électriques et lumineuses
Le contenu de la feuille d’interprétation 1 de juillet 2017 a été pris en considération dans cet exemplaire.
General Information
Relations
Standards Content (Sample)
IEC 60809 ®
Edition 3.0 2017-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Lamps for road vehicles – Dimensional, electrical and luminous requirements
Lampes pour véhicules routiers – Exigences dimensionnelles, électriques et
lumineuses
IEC 60809:2014-12/AMD1:2017-03(en-fr)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales, électriques. Il contient 20 000 termes et définitions en anglais
Spécifications techniques, Rapports techniques et autres et en français, ainsi que les termes équivalents dans 16
documents de l'IEC. Disponible pour PC, Mac OS, tablettes langues additionnelles. Egalement appelé Vocabulaire
Android et iPad. Electrotechnique International (IEV) en ligne.
Recherche de publications IEC - www.iec.ch/searchpub Glossaire IEC - std.iec.ch/glossary
La recherche avancée permet de trouver des publications IEC 65 000 entrées terminologiques électrotechniques, en anglais
en utilisant différents critères (numéro de référence, texte, et en français, extraites des articles Termes et Définitions des
comité d’études,…). Elle donne aussi des informations sur les publications IEC parues depuis 2002. Plus certaines entrées
projets et les publications remplacées ou retirées. antérieures extraites des publications des CE 37, 77, 86 et
CISPR de l'IEC.
IEC Just Published - webstore.iec.ch/justpublished
Restez informé sur les nouvelles publications IEC. Just Service Clients - webstore.iec.ch/csc
Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur cette
Disponible en ligne et aussi une fois par mois par email. publication ou si vous avez des questions contactez-nous:
csc@iec.ch.
IEC 60809 ®
Edition 3.0 2017-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Lamps for road vehicles – Dimensional, electrical and luminous requirements
Lampes pour véhicules routiers – Exigences dimensionnelles, électriques et
lumineuses
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.140.20; 43.040.20 ISBN 978-2-8322-4138-7
IEC 2017
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
IEC 60809
Edition 3.0 2014-12
LAMPS FOR ROAD VEHICLES –
DIMENSIONAL, ELECTRICAL AND LUMINOUS REQUIREMENTS
INTERPRETATION SHEET 1
This interpretation sheet has been prepared by subcommittee 34A: Lamps, of IEC technical
committee 34: Lamps and related equipment.
The text of this interpretation sheet is based on the following documents:
ISH Report on voting
34A/2007/ISH 34A/2017/RVD
Full information on the voting for the approval of this interpretation sheet can be found in the
report on voting indicated in the above table.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
___________
Introduction (not part of the proposal)
In the Amendment 1 to Ed.3 (34A/1901/CDV voted positively), Annex E was updated to
extend the method of measuring internal elements of dual filament lamps to all such
categories, for instance the new category H19.
In the amendment of the current category sheet for H19 (Regulation No. 37), the distinct
physical shield width B is introduced (8,6 ± 0,3 mm) to ensure interchangeability of light
sources as it relates to road safety (see WP.29/2016/111; to become Resolution [R.E.5] on
the common specification of light source categories). In the category sheet for H19 reference
is made to Annex E of IEC 60809:2014 for the method of measurement of the internal
elements.
ICS 29.140.20; 43.040.20
IEC 60809:2014-12/AMD1:2017-03/ISH1:2017-07(en-fr)
– 2 – IEC 60809:2014/AMD1:2017/ISH1:2017
IEC 2017
See in Figure 1 an extract from WP.29/2016/111.
Practical measurement set-ups use optical vision-systems like a projection system to
determine the dimensions of the internal elements.
Figure 1 – Category sheet for H19
Problem statement:
When using the above mentioned vision system, a measurement error is introduced due to
refraction and blurring (by the glass envelope), additional to the measurement uncertainty.
The effect is mainly dependent on the shield width in relation to the glass envelope diameter.
For lamp designs with a relatively small glass envelope diameter (there is only an upper limit
specified), the shield gets close to the glass envelope and the effect becomes significant.
Figure 2 shows a simplified drawing of the view imaging situations of the shield, with and
without the effect due to the “refractive index” of the glass envelope.
a) Physical dimension “B” when the glass envelope is removed,
b) Visual size of the shield width when measured through the glass envelope in direction ,
resulting in a “smaller value for “B”.
c) Visual size of the shield width when measured through the glass envelope in direction
“-” (the opposite direction as defined in IEC 60809:2014/AMD1:2017), even show the
contrary deviation from the real dimension, resulting in a “larger value for “B”.
IEC 2017
Determination from viewing direction results in a smaller value than real
a)
b)
Lines indicating the “cut-of” lines for light safety
Shield
Glass envelope
a)
c)
Determination from viewing direction “-” results in a larger value than real
Figure 2 – Simplified drawing of the imaging situations
Proposal:
To publish an Interpretation Sheet on Clause E.5 of IEC 60809:2014/AMD1:2017, Lamps for
road vehicles – Dimensional, electrical and luminous requirements, as follows:
INTERPRETATION SHEET
Clause E.5 of IEC 60809:2014/AMD1:2017, Lamps for road vehicles –
Dimensional, electrical and luminous requirements
Note to MP 24 to MP 25 in Table E.1
To avoid measurement errors of the shield width B due to the refractions by the glass
envelope the following options are considered:
1) The removal of the glass envelope.
2) The use of X-ray measurement.
NOTE 1 Option 1 can be used for verification.
3) The use of an immersion fluid inside and outside of the envelope in a rectangular glass
bath ensuring the refractive index of the immersion fluid matches that of the glass
envelope close enough to avoid refractions. The immersion fluid can be filled inside the
envelope after removing the top of the bulb. Care shall be taken not to touch/move
internal elements.
NOTE 2 Option 1 can be used for verification of the immersion fluid and the test setup.
4) The use of a correction factor, taking into account the optical offset and the measurement
uncertainty. The verification of the correction factor for a certain lamp design shall be
made according the measurement method under item “1)” i.e. after removal of the glass
envelope.
NOTE 3 Option 1 can be used for verification.
Note to this interpretation sheet:
The next revision of this standard shall incorporate an improvement of the body text to
elminate the need for this interpretation sheet.
– 2 – IEC 60809:2014/AMD1:2017
© IEC 2017
FOREWORD
This amendment has been prepared by subcommittee 34A: Lamps, of IEC technical
committee 34: Lamps and related equipment.
The text of this amendment is based on the following documents:
CDV Report on voting
34A/1901/CDV 34A/1940/RVC
Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC website under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
The contents of the interpretation sheet 1 of July 2017 have been included in this copy.
___________
4.4.1 Colour of light
Add, after the third dashed list item (definition of red colour), the following new text:
– finished filament lamps emitting amber light:
A green boundary: y = x – 0,120
A the spectral locus
A red boundary: y = 0,390
A white boundary: y = 0,790 – 0,670 x
With intersection points:
A : x = 0,545, y = 0,425
A : x = 0,560, y = 0,440
A : x = 0,609, y = 0,390
A : x = 0,597, y = 0,390
Annex E
Replace the existing title with the following new title:
IEC 2017
Method of measuring internal elements of H4, H17, H19 and HS1 lamps
E.2.6 Plane Y1-Y1
Replace the existing paragraph with the following new text:
Plane Y1-Y1 is a plane parallel to the reference plane at a distance of 29,5 mm from it
(30,0 mm for the 24 V type, 30,5 mm for category H19).
E.2.8 Plane Y3-Y3
Replace the existing paragraph with the following new text:
Plane Y3-Y3 is a plane parallel to the reference plane at a distance of 23,5 mm from it
(25,0 mm for categories HS1 and H17, 24,5 mm for category H19).
E.3 Viewing directions (see Figure E.1)
Add, at the end of Clause E.3, the following new sub-clause:
E.3.4 Viewing direction
Viewing direction is perpendicular to plane V-V, seen from the side of the right-hand shield
edge.
E.4.1 Shield and filaments (see Figure E.2)
Replace the existing text with the following new text:
Viewing direction
MP 1 and MP 2 The intersections of the main beam filament axis with planes Y3-Y3
and Y4-Y4
MP 3 and MP 4 The intersections of the shield edge with planes Y1-Y1 and Y2-Y2
MP 5 and MP 6 The intersections of the envelope of the dipped beam filament with
planes Y1-Y1 and Y2-Y
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.