IEC 60809:2021 is applicable to electric light sources for use in automotive applications, for example in road illumination devices and/or light signalling devices for road vehicles.
It is especially applicable to light sources listed in UN Resolution R.E.5 and light sources subject to other legislations.
This fourth edition cancels and replaces the third edition published in 2014, Amendment 1:2017, Amendment 2:2017 and Amendment 3:2019. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Introduction of a light technical measurement on LED light sources intended for use in front-lighting applications.
b) As the original data sheets and some figures from previous editions were not available in an editable format, they have been reproduced from their old format, following the current drafting rules and are now in single language format. Some reproductions constitute minor (obvious) editorial changes of the original text sections and original figures; no technical changes were introduced.

  • Standard
    94 pages
    English language
    sale 15% off
  • Standard
    182 pages
    English and French language
    sale 15% off
  • Standard
    390 pages
    English and French language
    sale 15% off

This document is applicable to electric light sources (see Note 1) for use in automotive
applications, for example in road illumination devices and/or light signalling devices for road
vehicles.
It is especially applicable to light sources listed in UN Resolution R.E.5 and light sources subject
to other legislations.
This document specifies the technical requirements for interchangeability for example
dimensional, electrical and photometrical characteristics, and includes test methods.
For the light sources listed in this document, the data sheets are contained either in this
document or are included by reference to UN Resolution R.E.5.
Performance requirements are specified in IEC 60810, for example life, torsion strength,
resistance to vibration and shock.
The requirements for miniature light sources for supplementary purposes, not subject to
legislation, are specified in IEC 60983.
NOTE 1 The terms "lamp" and "light source" are both used in this document to mean the same product, so the two
terms are interchangeable throughout this document.
NOTE 2 In various vocabularies and standards, different terms are used for "incandescent lamp"
(IEC 60050845:
1987, 845-07-04), "discharge lamp" (IEC 60050-845:1987, 845-07-17) and "LED lamp". In this
document "filament lamp", "discharge lamp" and "LED light source" are used, however, where only "lamp" or "light
source" is written, all light sources, independent of the technology used, are meant, unless the context clearly shows
that it applies to one kind of technology only. In the UN Regulations, the word "light source" is used for the products
specified in this document.
NOTE 3 Wherever the term "device" is used, it is meant to designate equipment which is used as a luminaire. It
can for instance take the form and purpose of a headlight or signal light.

  • Standard
    97 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document is applicable to electric light sources (see Note 1) for use in automotive applications, for example in road illumination devices and/or light signalling devices for road vehicles. It is especially applicable to light sources listed in UN Resolution R.E.5 and light sources subject to other legislations. This document specifies the technical requirements for interchangeability for example dimensional, electrical and photometrical characteristics, and includes test methods. For the light sources listed in this document, the data sheets are contained either in this document or are included by reference to UN Resolution R.E.5. Performance requirements are specified in IEC 60810, for example life, torsion strength, resistance to vibration and shock. The requirements for miniature light sources for supplementary purposes, not subject to legislation, are specified in IEC 60983. NOTE 1 The terms "lamp" and "light source" are both used in this document to mean the same product, so the two terms are interchangeable throughout this document. NOTE 2 In various vocabularies and standards, different terms are used for "incandescent lamp" (IEC 60050845:1987, 845-07-04), "discharge lamp" (IEC 60050-845:1987, 845-07-17) and "LED lamp". In this document "filament lamp", "discharge lamp" and "LED light source" are used, however, where only "lamp" or "light source" is written, all light sources, independent of the technology used, are meant, unless the context clearly shows that it applies to one kind of technology only. In the UN Regulations, the word "light source" is used for the products specified in this document. NOTE 3 Wherever the term "device" is used, it is meant to designate equipment which is used as a luminaire. It can for instance take the form and purpose of a headlight or signal light.

  • Standard
    97 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Second CDV circulated to follow IEC

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC TR 61547-1:2020 is available as IEC TR 61547-1:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC TR 61547-1:2020 describes an objective light flickermeter, which can be applied for the following purposes:
- measuring the intrinsic performance of all lighting equipment without the application of voltage fluctuations in terms of illuminance flicker; during this measurement, the lighting equipment is supplied with a stable mains;
- testing the immunity performance of lighting equipment against (unintentional) voltage fluctuation disturbance on the AC mains in terms of illuminance flicker; during this test a set of defined voltage fluctuations are applied to the AC mains and the immunity of the lighting equipment to the disturbance is determined.
Apart from the above two purposes, the immunity performance of lighting equipment can also be tested against intentional voltage fluctuation on the AC mains arising for example from mains signalling. This is however not described in further detail in this document. This third edition cancels and replaces the second edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- the scope of this document has been clarified to make a distinction between flicker testing without voltage fluctuations to measure the intrinsic performance of lighting equipment and flicker testing in which a specific set of voltage fluctuations are applied in order to measure the immunity of the lighting equipment to voltage fluctuations present on the mains;
- the test procedure for flicker testing has been clarified.

  • Technical report
    46 pages
    English language
    sale 15% off
  • Technical report
    96 pages
    English language
    sale 15% off

IEC 61097-4:2012(E) specifies the performance requirements and methods of testing for Inmarsat-C ship earth stations (SES) capable of transmitting and receiving direct-printing communications, and for enhanced group call (EGC) receivers, for use in the GMDSS and for use for long-range identification and tracking (LRIT).

  • Standard
    29 pages
    English language
    sale 15% off
  • Standard
    59 pages
    English language
    sale 15% off
  • Standard
    64 pages
    English language
    sale 15% off

IEC 60809:2014 is applicable to replaceable and standardised lamps (filament lamps, discharge lamps and LED light sources) to be used in headlamps, fog-lamps and signalling lamps for road vehicles. In some applications, these lamps may be installed as non-replaceable. This third edition cancels and replaces the second edition (1995), its Amendment 1 (1996), its Amendment 2 (2002), its Amendment 3 (2004), its Amendment 4 (2009) and its Amendment 5 (2012). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) the introduction of requirements for non-replaceable filament lamps;
b) the introduction of requirements for LED light sources.

  • Standard
    162 pages
    English and French language
    sale 15% off
  • Standard
    366 pages
    English and French language
    sale 15% off
  • Standard
    352 pages
    English and French language
    sale 15% off
  • Standard
    333 pages
    English and French language
    sale 15% off

This International Standard specifies the performance requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications: · Projection (including cinematograph and still projection) · · Photographic (including studio) · · Floodlighting · · Special purpose · · General purpose · · Stage lighting This third edition cancels and replaces the second edition published in 1982 and amendments 1(1984), 2(1985), 3(1987), 4(1989), 5(1992), 6(1993), 7(1994), 8(1995), 9(1996), 10(1996), 11(1997), 12(1999) and 13(2000

  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62504:2014 is of assistance in the common understanding of terms and definitions, relevant for general lighting with LED technology. The terms included are those already available in IEC LED standards or used in manufacturers' literature. This standard provides descriptive terms (like "LED light sources") and measurable terms when modified from IEC 60050-845 (like "colour rendering index"). This first edition cancels and replaces the IEC TS 62504 published in 2011. The significant changes with respect to IEC TS 62504 are as follows:
a) Terms from the International Electrotechnical Vocabulary that have not been modified are deleted;
b) Alignment with the CIE has been done;
c) An introduction has been added.

  • Standard
    50 pages
    English and French language
    sale 15% off
  • Standard
    98 pages
    English and French language
    sale 15% off

This document is applicable to filament lamps, discharge lamps, LED light sources and LED
packages to be used in road vehicles, i.e. in headlamps, fog-lamps, signalling lamps and
interior lighting. It is especially applicable to those lamps and light sources which are listed in
IEC 60809.
It specifies requirements and test methods for the measurement of performance characteristics
such as lamp life, luminous flux maintenance, torsion strength, glass bulb strength
and resistance to vibration and shock. Moreover, information on temperature limits, maximum
lamp outlines and maximum tolerable voltage surges is given as guidance for lighting and
electrical equipment design.
For some of the requirements given in this document, reference is made to data given in
tables. For lamps not listed in such tables, the relevant data are supplied by the lamp
manufacturer or responsible vendor.
The performance requirements are additional to the basic requirements specified in
IEC 60809. They are, however, not intended to be used by authorities for legal type-approval
purposes.
NOTE 1 In the various vocabularies and standards, different terms are used for "incandescent lamp"
(IEC 60050-845:1987, 845-07-04) and "discharge lamp" (IEC 60050-845:1987, 845-07-17). In this document,
"filament lamp" and "discharge lamp" are used. However, where only “lamp” is written both types are meant, unless
the context clearly shows that it applies to one type only.
NOTE 2 This document does not apply to luminaires.
NOTE 3 In this document, the term LED light source is used, in other standards the term LED lamps can be used
to describe similar products.

  • Standard
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    13 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day

IEC TR 61547-1:2017(E) describes an objective light flickermeter, which can be applied for, amongst others, the following purposes:
- testing the intrinsic performance of all lighting equipment without voltage fluctuations;
- testing the immunity performance of lighting equipment against (unintentional) voltage fluctuation disturbance on the AC power port;
- testing the immunity performance of lighting equipment against intentional voltage fluctuation on the AC power port arising for example from ripple control systems.
This second edition cancels and replaces the first edition published in 2015. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a. the title of Part 1 has been changed to reflect the more general application of the objective flickermeter;
b. the specific voltage fluctuation immunity test method has been extended for lighting equipment rated for 120 V AC and 230 V AC, 50 Hz and 60 Hz.

  • Technical report
    39 pages
    English language
    sale 15% off
  • Technical report
    39 pages
    English language
    sale 15% off

IEC 62908-1-2:2017(E) provides a list of terminological entries that are frequently used in the literature related to touch and interactive displays in the IEC 62908 series. Terms for various input methods such as touch, hovering, proximity, gesture, eye tracking, and motion recognition are included. This document is applicable to touch displays, interactive displays and their components.

  • Standard
    13 pages
    English language
    sale 15% off

The contents of the interpretation sheet 1 of July 2017 have been included in this copy.

  • Standard
    13 pages
    English and French language
    sale 15% off

IEC 61280-4-4:2017 provides uniform methods of measuring polarization mode dispersion (PMD) of single-mode installed links. An installed link is the optical path between transmitter and receiver, or a portion of that optical path. These measurements can be used to assess the suitability of a given link for high bit rate applications, or to provide insight on the relationships of various related transmission attributes. This document focuses on the measurement methods and requirements for measuring long lengths of installed cabling that can also include other optical elements, such as splices, connectors, amplifiers, chromatic dispersion compensating modules, dense wavelength division multiplexing or multiplexer (DWDM) components, multiplexers, wavelength selective switches, re-configurable optical add drop multiplexer (ROADMS). This document focuses on the apparatus, procedures, and calculations needed to complete measurements. IEC TR 61282-9 explains the theory behind the test methods. This second edition cancels and replaces the first edition published in 2006. This second edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- theory is removed and replaced with a reference to IEC TR 61282-9;
- a new method, wavelength scanning OTDR and SOP analysis (WSOSA), is added as Annex G;
- a brief description of each method is added to Clause 5;
- Methods E and F are converted to informative Annexes E and F;
- a new Clause (6) on measurement configurations is added;
- a new Clause (7) on measurement considerations is added;
- Clause 10 on procedure is expanded;
- several of the apparatus diagrams are improved;
- several clarifications about what is measured and what is calculated have been made in Annex H.

  • Standard
    82 pages
    English language
    sale 15% off
  • Standard
    169 pages
    English and French language
    sale 15% off

This International Standard specifies the performance requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications: · Projection (including cinematograph and still projection) · · Photographic (including studio) · · Floodlighting · · Special purpose · · General purpose · · Stage lighting This third edition cancels and replaces the second edition published in 1982 and amendments 1(1984), 2(1985), 3(1987), 4(1989), 5(1992), 6(1993), 7(1994), 8(1995), 9(1996), 10(1996), 11(1997), 12(1999) and 13(2000

  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard specifies lamps, or information relevant to lamps, not given elsewhere in existing IEC lamp standards. It covers both safety and performance aspects.

  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60432-3:2012 specifies the safety requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications: - projection (including cinematograph and still projection), - photographic (including studio), - floodlighting, - special purpose, - general purpose, - stage lighting. This second edition of IEC 60432-3 cancels and replaces the first edition published in 2002, Amendment 1 (2005) and Amendment 2 (2008). The main changes with respect to the previous edition are as follows: - adapting the cold fill pressure requirements and tests for self-shielded lamps to the state of the technology, - introduction of requirements to fully cover photobiological safety according to IEC 62471.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    13 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day

IEC 62150-3:2015 It has been found that some optical transceivers and receptacles are susceptible to fibre optic cable induced stress when side forces are applied to the mated cable-connector assembly, resulting in variations in the transmitted optical power. The purpose of this part of IEC 62150 is to define physical stress tests to ensure that such optical connections (cable and receptacle) can continue to function within specifications. This standard specifies the test requirements and procedures for qualifying optical devices for sensitivity to coupled power variations induced by mechanical disturbance at the optical ports of the device. This standard applies to active devices with optical receptacle interfaces. This standard describes the testing of transceivers for use with single-mode connectors having either 2,5 mm or 1,25 mm ferrules. This second edition cancels and replaces the first edition published in 2012 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- extension of application field to SC connector interface transceivers in addition to LC connector interface transceivers specified in the first edition as both transceiver interfaces are very important in the industry;
- addition of a new Annex E dealing with load value difference for connector type in Method A.
Keywords: fibre optic cable induced stress, power variations induced by mechanical disturbance

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    45 pages
    English and French language
    sale 15% off

IEC TR 61547-1:2015(E) establishes an objective method and procedure for testing the immunity performance of lighting equipment against voltage fluctuation disturbances on the a.c. power port. The object of this Technical Report is to establish a common and objective reference for evaluating the immunity of lighting equipment in terms of illuminance flicker when subjected to mains voltage fluctuations. Temporal changes in the colour of the light (chromatic flicker) are not considered in this test.

  • Technical report
    36 pages
    English language
    sale 15% off

This part of IEC 60432 specifies the safety and the related interchangeability requirements of tungsten halogen lamps for general lighting service. It covers those tungsten halogen lamps that are used as direct replacements for conventional tungsten filament lamps as well as new tungsten halogen lamps which have no correspondence in IEC 60432-1, but for which the safety and interchangeability requirements are treated by this standard in conjunction with IEC 60432-1. These tungsten halogen lamps have the following characteristics:
– rated wattage up to and including 250 W;
– rated voltage of 50 V to 250 V inclusive;
– caps B15d, B22d, E12, E14, E17, E26, E26d, E26/5039, E27 or E27/5139.
This standard also covers single-ended lamps, within the above ratings, which are not direct
replacements for conventional tungsten filament lamps, but serve the same purpose.
NOTE 1 There is no implication that a tungsten halogen lamp used as a substitute for an incandescent tungsten filament lamp would use the same bulb shape as the original incandescent lamp. NOTE 2 There are two variations of E26 caps which are not fully compatible. E26/24 caps are used in North merica and E26/25 caps are used in Japan.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

International Standard IEC 60432-1 specifies the safety and interchangeability requirements of
tungsten filament incandescent lamps for general lighting service having:
– rated wattage up to and including 200 W;
– rated voltage of 50 V to 250 V inclusive;
– bulbs of the A, B, C, G, M, P, PS, PAR or R shapes* , or other bulb shapes where the lamps
are intended to serve the same purpose as lamps with the foregoing bulb shapes;
– bulbs with all kinds of finishes;
– caps B15d, B22d, E12, E14, E17, E26** , E26d, E26/5039, E27 or E27/5139.
As far as is reasonably practicable, this standard is also applicable to lamps with bulbs and caps other than those mentioned above, but which serve the same purpose. This standard specifies the method a manufacturer should use to show that his product conforms to this standard on the basis of whole production appraisal in association with his test records on finished products. This method can also be applied for certification purposes. Details of a batch test procedure which can be used to make limited assessment of batches are also given. This standard is concerned with safety criteria only and does not take into account the performance of tungsten filament lamps with respect to luminous flux, life or power consumption characteristics. Readers should refer to IEC 60064 for such characteristics with respect to types normally used for general lighting service.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC/TS 62504:2011 presents terms and definitions relevant for lighting with LED light sources. It provides both descriptive terms (such as 'built-in LED module') and measurable terms (such as 'luminance').

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61158-4-11:2014 specifies procedures for: the timely transfer of data and control information from one data-link user entity to a peer user entity, and among the data-link entities forming the distributed data-link service provider; procedures for giving communications opportunities to all participating DL entities, sequentially and in a cyclic manner for deterministic and synchronized transfer at cyclic intervals up to one millisecond; procedures for giving communication opportunities available for time-critical data transmission together with non-time-critical data transmission without prejudice to the time-critical data transmission; procedures for giving cyclic and acyclic communication opportunities for time-critical data transmission with prioritized access; procedures for giving communication opportunities based on standard ISO/IEC 8802-3 medium access control, with provisions for nodes to be added or removed during normal operation and the structure of the fieldbus DLPDUs used for the transfer of data and control information by the protocol of this standard, and their representation as physical interface data units. This third edition cancels and replaces the second edition published in 2010 and constitutes a technical revision. The main changes are: Subclauses 4.6.1, 4.6.4 and 5.4.6, Clause 6 and 7.2 for the loop-architecture are modified to cover the additional specifications for the higher data rate in the loop-architecture.

  • Standard
    330 pages
    English and French language
    sale 15% off

IEC 61158-3-1:2014 defines the services provided to the Type 1 fieldbus application layer at the boundary between the application and data-link layers of the fieldbus reference model and systems management at the boundary between the data-link layer and systems management of the fieldbus reference model. This second edition cancels and replaces the first edition published in 2007. It constitutes a technical revision. The main change is the improved terms.

  • Standard
    272 pages
    English and French language
    sale 15% off

IEC/TR 61341:2010 describes the method of measuring and specifying the centre beam intensity and the associated beam angle(s) of reflector lamps. It applies to: - incandescent, - tungsten halogen, - gas-discharge and LED based reflector lamps for general lighting purposes. It does not apply to lamps for special purposes such as projection lamps. This second edition cancels and replaces the first edition published in 1994 and constitutes a technical revision. Due to the increasing use of reflector equipped LED lamps, the scope has been broadened and measurement conditions been included in order to take account of these lamps. Further, for easier understanding of the relation between the different axis and different intensities, two figures have been added. The luminous intensity distribution shall be reported instead of the centre beam intensity, if the latter is very low ("butterfly" distributions).

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The contents of the corrigenda of September 1993 and May 1996 have been included in this copy.

  • Standard
    10 pages
    English and French language
    sale 15% off

Amandma A3:2011 je dodatek k standardu SIST EN 60357:2004.
This International Standard specifies the performance requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications:
- Projection (including cinematograph and still projection)
- Photographic (including studio)
- Floodlighting
- Special purpose
- General purpose
- Stage lighting
For some of the requirements given in this standard reference is made to "the relevant data sheet". For some lamps these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor. The requirements of this standard relate only to type testing.
NOTE The requirements and tolerances permitted by this standard correspond to testing of a type test sample, submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturer's production and being as close to the production centre point values as possible.
It may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes, see IEC 60410.

  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60255-149:2013 specifies minimum requirements for thermal protection relays. This standard includes specification of the protection function, measurement characteristics and test methodologies. The object is to establish a common and reproducible reference for evaluating dependent time relays which protect equipment from thermal damage by measuring a.c. current flowing through the equipment. Complementary input energizing quantities such as ambient, coolant, top oil and winding temperature may be applicable for the thermal protection specification set forth in this standard. This standard covers protection relays based on a thermal model with memory function.

  • Standard
    93 pages
    English and French language
    sale 15% off

IEC 60743:2013 applies to the terminology used to describe tools, devices, equipment and methods used in live working. It standardizes the name of tools, devices and equipment and permits their identification by providing definitions and illustrations. It contains some example illustrations. This third edition cancels and replaces the second edition, published in 2001, and its Amendment 1:2008.This edition constitutes a technical revision which includes the following significant technical changes with respect to the previous edition: the clause 2 has been simplified and refers directly to IEC 60050-651; some definitions have been moved to specific existing clauses. This new edition is complementary to IEC 60050-651. Different publications under the responsibility of TC 78 include terms and its definitions. IEC 60050-651 (IEV 651) provides precise, brief and correct definitions of internationally accepted concepts in the field of live working, and specifies the terms by which these defined concepts are known. Electropedia gives access to the terms and definitions of IEC 60050-651 (http://www.electropedia.org/). Each product standard gives definitions necessary for the understanding of certain terms used in a specific context. The IEC Glossary (http://std.iec.ch/glossary) gives on-line access to the information.

  • Standard
    128 pages
    English and French language
    sale 15% off

This part of IEC 60432 specifies the safety requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications:
• projection (including cinematograph and still projection),
• photographic (including studio),
• floodlighting,
• special purpose,
• general purpose,
• stage lighting,
This International Standard does not apply to general purpose single-capped tungsten halogen lamps, covered by IEC 60432-2, that are used as replacement for conventional tungsten filament lamps. This part of IEC 60432 covers photobiological safety according to IEC 62471 and IEC/TR 62471-2. Lamps covered by this part of IEC 60432 do not reach risk levels that require risk group marking if they are
a) floodlight lamps,
b) general purpose capsule lamps, or
c) general purpose reflector lamps.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard specifies lamps, or information relevant to lamps, not given elsewhere in existing IEC lamp standards. It covers both safety and performance aspects.

  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard specifies lamps, or information relevant to lamps, not given elsewhere in existing IEC lamp standards. It covers both safety and performance aspects.

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Amandma A6:2010 je dodatek k standardu SIST EN 60630:2001.
Comprises maximum lamp outlines for tungsten filament lamps for domestic and similar general lighting purposes. Common modifications: Delete the following throughout the text: Lamps with cap E17, E26 and E39.

  • Amendment
    14 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 60432 specifies the safety and the related interchangeability requirements of tungsten halogen lamps for general lighting service. It covers those tungsten halogen lamps that are used as direct replacements for conventional tungsten filament lamps as well as new tungsten halogen lamps which have no correspondence in IEC 60432-1, but for which the safety and interchangeability requirements are treated by this standard in conjunction with IEC 60432-1. These tungsten halogen lamps have the following characteristics:
– rated wattage up to and including 250 W;
– rated voltage of 50 V to 250 V inclusive;
– caps B15d, B22d, E12, E14, E17, E26, E26d, E26/5039, E27 or E27/5139.
This standard also covers single-ended lamps, within the above ratings, which are not direct
replacements for conventional tungsten filament lamps, but serve the same purpose.
NOTE 1 There is no implication that a tungsten halogen lamp used as a substitute for an incandescent tungsten filament lamp would use the same bulb shape as the original incandescent lamp. NOTE 2 There are two variations of E26 caps which are not fully compatible. E26/24 caps are used in North merica and E26/25 caps are used in Japan.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    9 pages
    English and French language
    sale 15% off

International Standard IEC 60432-1 specifies the safety and interchangeability requirements of
tungsten filament incandescent lamps for general lighting service having:
– rated wattage up to and including 200 W;
– rated voltage of 50 V to 250 V inclusive;
– bulbs of the A, B, C, G, M, P, PS, PAR or R shapes* , or other bulb shapes where the lamps
are intended to serve the same purpose as lamps with the foregoing bulb shapes;
– bulbs with all kinds of finishes;
– caps B15d, B22d, E12, E14, E17, E26** , E26d, E26/5039, E27 or E27/5139.
As far as is reasonably practicable, this standard is also applicable to lamps with bulbs and caps other than those mentioned above, but which serve the same purpose. This standard specifies the method a manufacturer should use to show that his product conforms to this standard on the basis of whole production appraisal in association with his test records on finished products. This method can also be applied for certification purposes. Details of a batch test procedure which can be used to make limited assessment of batches are also given. This standard is concerned with safety criteria only and does not take into account the performance of tungsten filament lamps with respect to luminous flux, life or power consumption characteristics. Readers should refer to IEC 60064 for such characteristics with respect to types normally used for general lighting service.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60432-3:2012 specifies the safety requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications:
- projection (including cinematograph and still projection),
- photographic (including studio),
- floodlighting,
- special purpose,
- general purpose,
- stage lighting.
This second edition of IEC 60432-3 cancels and replaces the first edition published in 2002, Amendment 1 (2005) and Amendment 2 (2008). The main changes with respect to the previous edition are as follows:
- adapting the cold fill pressure requirements and tests for self-shielded lamps to the state of the technology,
- introduction of requirements to fully cover photobiological safety according to IEC 62471.

  • Standard
    65 pages
    English and French language
    sale 15% off