IEC TS 63202-3:2023
(Main)Photovoltaic cells - Part 3: Measurement of current-voltage characteristics of bifacial photovoltaic cells
Photovoltaic cells - Part 3: Measurement of current-voltage characteristics of bifacial photovoltaic cells
IEC TS 63202-3:2023 describes procedures for the measurement of current-voltage (I-V) characteristics of crystalline silicon bifacial photovoltaic (PV) cells for both laboratory and mass production applications.
This document is intended to be used for measurement of individual unencapsulated bifacial PV cells, in addition to the requirements described in IEC 60904-1 and differentiating from IEC TS 60904-1-2 which is more applicable to encapsulated PV device. Specific requirements on bifacial reference cells and calibration of solar simulators are also defined to provide useful guidance for the proposed methods.
General Information
Standards Content (Sample)
IEC TS 63202-3 ®
Edition 1.0 2023-02
TECHNICAL
SPECIFICATION
colour
inside
Photovoltaic cells –
Part 3: Measurement of current-voltage characteristics of bifacial photovoltaic
cells
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 63202-3 ®
Edition 1.0 2023-02
TECHNICAL
SPECIFICATION
colour
inside
Photovoltaic cells –
Part 3: Measurement of current-voltage characteristics of bifacial photovoltaic
cells
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 27.160 ISBN 978-2-8322-6415-7
– 2 – IEC TS 63202-3:2023 © IEC 2023
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Methods . 7
4.1 General . 7
4.2 Double-side simultaneous irradiation . 8
4.3 Equivalent irradiation . 8
4.4 Sequential irradiation . 10
5 Apparatus . 11
5.1 General . 11
5.2 Double-side simultaneous irradiation . 11
5.3 Equivalent irradiation . 11
5.4 Sequential irradiation . 12
6 Procedures . 12
6.1 General . 12
6.2 Double-side simultaneous irradiation . 12
6.2.1 Requirements for calibration . 12
6.2.2 Procedures . 13
6.3 Equivalent irradiation . 13
6.3.1 Requirements for calibration . 13
6.3.2 Procedures . 13
6.4 Sequential irradiation . 14
6.4.1 Requirements for calibration . 14
6.4.2 Procedures . 14
7 Report . 15
Annex A (normative) Determination of bifacial I-V characteristics . 16
A.1 General . 16
A.2 Shift approximation . 16
A.3 Linear interpolation . 17
Figure 1 – Schematic procedure of double-side simultaneous irradiation method with
integrated flash conditions . 8
Figure 2 – Schematic procedure of equivalent irradiation method with sequential flash
conditions . 9
Figure 3 – Schematic procedure of equivalent irradiation method with integrated flash
conditions . 10
Figure 4 – Schematic procedure of sequential irradiation method with integrated flash
conditions . 10
Figure 5 – Separate solar simulator on both front and rear side for double-side
simultaneous irradiation . 11
Figure 6 – Setup for equivalent irradiation with adjustable intensity . 12
Figure 7 – Schematic configuration with two consecutive solar simulators . 12
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
PHOTOVOLTAIC CELLS –
Part 3: Measurement of current-voltage
characteristics of bifacial photovoltaic cells
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC TS 63202-3 has been prepared by IEC technical committee 82: Solar photovoltaic energy
systems. It is a Technical Specification.
The text of this Technical Specification is based on the following documents:
Draft Report on voting
82/2070/DTS 82/2094/RVDTS
82/2094A/RVDTS
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this Technical Specification is English.
– 4 – IEC TS 63202-3:2023 © IEC 2023
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at https://www.iec.ch/members_experts/refdocs. The main document types developed by IEC
are described in greater detail at https://www.iec.ch/standardsdev/publications.
A list of all parts in the IEC 63202 series, published under the general title Photovoltaic cells,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The "colour inside" logo on the cover page of this document indicates that it
contains colours which are considered to be useful for the correct understanding of its
contents. Users should therefore print this document using a colour printer.
PHOTOVOLTAIC CELLS –
Part 3: Measurement of current-voltage
characteristics of bifacial photovoltaic cells
1 Scope
This part of IEC 63202 describes procedures for the measurement of current-voltage (I-V)
characteristics of crystalline silicon bifacial photovoltaic (PV) cells for both laboratory and mass
production applications.
This document is intended to be used for measurement of individual unencapsulated bifacial
PV cells, in addition to the requirements described in IEC 60904-1 and differentiating from
IEC TS 60904-1-2 which is more applicable to encapsulated PV device. Specific requirements
on bifacial reference cells and calibration of solar simulators are also defined to provide useful
guidance for the proposed methods.
The bifacial I-V characteristics contain front standard test condition (STC), rear STC and bifacial
STC results for the bifacial PV cells under test. Thus, bifaciality as well as the power generation
capability under single-side or bifacial irradiation are evaluated.
NOTE This document does not apply to tandem or multi-junction bifacial PV cells.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.