IEC 60364-5-56:2018
(Main)Low-voltage electrical installations - Part 5-56: Selection and erection of electrical equipment - Safety services
Low-voltage electrical installations - Part 5-56: Selection and erection of electrical equipment - Safety services
IEC 60364-5-56:2018 is available as IEC 60364-5-56:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60364-5-56:2018 covers general requirements for safety services, selection and erection of electrical supply systems for safety services and electrical safety sources. Standby electrical supply systems are outside the scope of this part. This part does not apply to installations in hazardous areas (BE3), for which requirements are given in IEC 60079-14. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
1) Modifications to normative references and terms and definitions.
2) Under electrical circuits for safety services, addition of requirements concerning circuit and overcurrent protection in order to maintain reliability of safety service power supplies under fire conditions.
3) Under electrical circuits for safety services, addition of requirements stating that circuits for safety services are not to be protected by RCDs or AFDDs.
4) Under emergency lighting applications, addition of requirements to prevent emergency lighting systems being adversely affected by any control system.
5) Addition of requirements for all emergency luminaires in the area to provide full design light output in the event of any final circuit failure.
6) Addition of a new Annex D (informative): Fire switch.
7) Addition of a new Annex E (informative): Example of installation methods of safety services with cable management system.
8) Addition of a new Annex F (informative): Wiring systems.
9) Addition of a new Annex G (informative): Guidance on suitable locations for electrical sources for safety services.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 60364-5-56 ®
Edition 3.0 2018-11
INTERNATIONAL
STANDARD
Low-voltage electrical installations –
Part 5-56: Selection and erection of electrical equipment – Safety services
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 60364-5-56 ®
Edition 3.0 2018-11
INTERNATIONAL
STANDARD
Low-voltage electrical installations –
Part 5-56: Selection and erection of electrical equipment – Safety services
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 91.140.50 ISBN 978-2-8322-6180-4
– 2 – IEC 60364-5-56:2018 © IEC 2018
CONTENTS
FOREWORD . 3
560.1 Scope . 5
560.2 Normative references . 5
560.3 Terms and definitions . 6
560.4 Classification . 8
560.5 General . 8
560.6 Electrical sources for safety services . 9
560.7 Electrical circuits of safety services. 10
560.8 Wiring systems . 11
560.9 Emergency lighting applications . 12
560.10 Fire protection applications/equipment . 14
Annex A (informative) Guidance for emergency lighting . 15
Annex B (informative) Guidance for fire protection equipment . 16
Annex C (informative) List of notes concerning certain countries . 17
Annex D (informative) Fire switch . 21
Annex E (informative) Example of installation methods of safety services with cable
management system . 22
Annex F (informative) Wiring systems . 23
F.1 Ambient test temperature rise . 23
F.2 Duration of the safety service. 23
F.3 Expected resistance of feeder conductors . 23
F.4 Protection against electric shock in the event of a failure by means of the
touch voltage reduction . 24
F.5 Conductor resistance in case of fire . 24
F.6 High temperature effects . 25
F.7 Feeder circuits . 25
Annex G (informative) Guidance on suitable locations for electrical sources for safety
services . 26
G.1 Recommendations for a suitable location for an electrical source for safety
services . 26
G.2 Conditions of fire protection . 26
Bibliography . 27
Figure D.1 – Fire switch installation . 21
Figure E.1 – Example of cable installation for safety services . 22
Table A.1 – Guidance for emergency lighting . 15
Table B.1 – Guidance for safety equipment . 16
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LOW-VOLTAGE ELECTRICAL INSTALLATIONS –
Part 5-56: Selection and erection of electrical equipment –
Safety services
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60364-5-56 has been prepared by IEC technical committee 64:
Electrical installations and protection against electric shock.
This third edition cancels and replaces the second edition published in 2009. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
1) Modifications to normative references and terms and definitions.
2) Under electrical circuits for safety services, addition of requirements concerning circuit
and overcurrent protection in order to maintain reliability of safety service power supplies
under fire conditions.
3) Under electrical circuits for safety services, addition of requirements stating that circuits
for safety services are not to be protected by RCDs or AFDDs.
– 4 – IEC 60364-5-56:2018 © IEC 2018
4) Under emergency lighting applications, addition of requirements to prevent emergency
lighting systems being adversely affected by any control system.
5) Addition of requirements for all emergency luminaires in the area to provide full design
light output in the event of any final circuit failure.
6) Addition of a new Annex D (informative): Fire switch.
7) Addition of a new Annex E (informative): Example of installation methods of safety
services with cable management system.
8) Addition of a new Annex F (informative): Wiring systems.
9) Addition of a new Annex G (informative): Guidance on suitable locations for electrical
sources for safety services.
The text of this International Standard is based on the following documents:
FDIS Report on voting
64/2316/FDIS 64/2341/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
The reader’s attention is drawn to the fact that Annex C lists all of the “in-some-country”
clauses on differing practices of a less permanent nature relating to the subject of this
standard.
A list of all parts in the IEC 60364 series, published under the general title Low-voltage
electrical installations, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
LOW-VOLTAGE ELECTRICAL INSTALLATIONS –
Part 5-56: Selection and erection of electrical equipment –
Safety services
560.1 Scope
This part of IEC 60364 covers general requirements for safety services, selection and erection
of electrical supply systems for safety services and the electrical source for safety services.
Standby electrical supply systems are outside the scope of this document. This document
does not apply to installations in hazardous areas (BE3), for which requirements are given in
IEC 60079-14.
560.2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requiremen
...
IEC 60364-5-56 ®
Edition 3.0 2018-11
REDLINE VERSION
INTERNATIONAL
STANDARD
colour
inside
Low-voltage electrical installations –
Part 5-56: Selection and erection of electrical equipment – Safety services
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 60364-5-56 ®
Edition 3.0 2018-11
REDLINE VERSION
INTERNATIONAL
STANDARD
colour
inside
Low-voltage electrical installations –
Part 5-56: Selection and erection of electrical equipment – Safety services
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 91.140.50 ISBN 978-2-8322-6220-7
– 2 – IEC 60364-5-56:2018 RLV © IEC 2018
CONTENTS
FOREWORD . 3
560.1 Scope . 6
560.2 Normative references . 6
560.3 Terms and definitions . 7
560.4 Classification . 9
560.5 General . 10
560.6 Electrical sources for safety services . 10
560.7 Electrical circuits of safety services. 13
560.8 Wiring systems . 14
560.9 Emergency escape lighting applications . 15
560.10 Fire protection applications/equipment . 17
Annex A (informative) Guidance for emergency lighting . 18
Annex B (informative) Guidance for fire protection equipment . 20
Annex C (informative) List of notes concerning certain countries . 22
Annex D (informative) Fire switch . 29
Annex E (informative) Example of installation methods of safety services with cable
management system . 30
Annex F (informative) Wiring systems . 31
F.1 Ambient test temperature rise . 31
F.2 Duration of the safety service. 31
F.3 Expected resistance of feeder conductors . 31
F.4 Protection against electric shock in the event of a failure by means of the
touch voltage reduction . 32
F.5 Conductor resistance in case of fire . 32
F.6 High temperature effects . 33
F.7 Feeder circuits . 33
Annex G (informative) Guidance on suitable locations for electrical sources for safety
services . 34
G.1 Recommendations for a suitable location for an electrical source for safety
services . 34
G.2 Conditions of fire protection . 34
Bibliography . 35
Figure D.1 – Fire switch installation . 29
Figure E.1 – Example of cable installation for safety services . 30
Table A.1 – Guidance for emergency lighting . 18
Table B.1 – Guidance for safety equipment . 20
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LOW-VOLTAGE ELECTRICAL INSTALLATIONS –
Part 5-56: Selection and erection of electrical equipment –
Safety services
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This redline version of the official IEC Standard allows the user to identify the changes
made to the previous edition. A vertical bar appears in the margin wherever a change
has been made. Additions are in green text, deletions are in strikethrough red text.
– 4 – IEC 60364-5-56:2018 RLV © IEC 2018
International Standard IEC 60364-5-56 has been prepared by IEC technical committee 64:
Electrical installations and protection against electric shock.
This third edition cancels and replaces the second edition published in 2009. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
1) Modifications to normative references and terms and definitions.
2) Under electrical circuits for safety services, addition of requirements concerning circuit
and overcurrent protection in order to maintain reliability of safety service power supplies
under fire conditions.
3) Under electrical circuits for safety services, addition of requirements stating that circuits
for safety services are not to be protected by RCDs or AFDDs.
4) Under emergency lighting applications, addition of requirements to prevent emergency
lighting systems being adversely affected by any control system.
5) Addition of requirements for all emergency luminaires in the area to provide full design
light output in the event of any final circuit failure.
6) Addition of a new Annex D (informative): Fire switch.
7) Addition of a new Annex E (informative): Example of installation methods of safety
services with cable management system.
8) Addition of a new Annex F (informative): Wiring systems.
9) Addition of a new Annex G (informative): Guidance on suitable locations for electrical
sources for safety services.
The text of this International Standard is based on the following documents:
FDIS Report on voting
64/2316/FDIS 64/2341/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
The reader’s attention is drawn to the fact that Annex C lists all of the “in-some-country”
clauses on differing practices of a less permanent nature relating to the subject of this
standard.
A list of all parts in the IEC 60364 series, published under the general title Low-voltage
electrical installations, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this publication using a colour printer.
– 6 – IEC 60364-5-56:2018 RLV © IEC 2018
LOW-VOLTAGE ELECTRICAL INSTALLATIONS –
Par
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.