IEC TS 60286-6-1:2023

Packaging of components for automatic handling - Part 6-1: Bulk case packaging for miniaturized surface mounting components

IEC TS 60286-6-1:2023 specifies a bulk case capable of containing miniaturized surface mount components of sizes within the range of 0402M to 1005M (see Table 1 for explanation of the codes). The bulk case is designed for transport and storage of components and to supply of components directly or by an appropriate feeder to the placement machine. The bulk case is equipped with a coupling interface to enable its automatic handling, e.g. by a robot or automatic handling machines.

General Information

• Status: Published
• Publication Date: 08-Nov-2023
• ICS: 31.020 - Electronic components in general
• Technical Committee: TC 40 - Capacitors and resistors for electronic equipment
• Drafting Committee: WG 36 - TC 40/WG 36
• Current Stage: PPUB - Publication issued
• Start Date: 11-Aug-2023
• Completion Date: 09-Nov-2023

Standards Content (Sample)

IEC TS 60286-6-1 ®
Edition 1.0 2023-11
TECHNICAL
SPECIFICATION
colour
inside
Packaging of components for automatic handling –
Part 6-1: Bulk case packaging for miniaturized surface mounting components

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Secretariat Tel.: [phone]
3, rue de Varembé [e-mail]
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc

If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: [e-mail].
IEC TS 60286-6-1 ®
Edition 1.0 2023-11
TECHNICAL
SPECIFICATION
colour
inside
Packaging of components for automatic handling –

Part 6-1: Bulk case packaging for miniaturized surface mounting components

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 31.020  ISBN 978-2-8322-7707-2

– 2 – IEC TS 60286-6-1:2023 © IEC 2023
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Requirements for the bulk case . 6
4.1 Case outline . 6
4.2 Shutter mechanism . 7
4.3 Dimensions . 7
4.4 Material . 9
4.5 Mechanical characteristics of the bulk case . 10
4.5.1 Mechanical stability . 10
4.5.2 Performance and test methods . 10
5 Marking of the bulk case . 10
5.1 General . 10
5.2 Recycling . 10
Annex A (informative) Packing capacity . 11
A.1 Component types . 11
A.2 Component quantities . 11
Annex B (informative) Label information. 12
B.1 Label material . 12
B.2 Label adhesion . 12
B.3 Label content . 12
Annex C (informative) Examples of requirements and test methods . 13
Bibliography . 14

Figure 1 – Bulk case – General view . 7
Figure 2 – Bulk case – Photographic view . 7
Figure 3 – Dimensions of the bulk case . 8
Figure B.1 – Example of a label with bar code . 12
Figure B.2 – Example of a label with a 2D symbol . 12
Figure B.3 – Example of a label with bar code and a 2D symbol . 12

Table 1 – Size codes for components . 6
Table 2 – Dimension of the bulk case . 9
Table A.1 – Typical quantities of Capacitors in the bulk case . 11
Table A.2 – Typical quantities of Resistors in the bulk case . 11
Table C.1 – Examples of requirements and test methods for the bulk case . 13

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
PACKAGING OF COMPONENTS FOR AUTOMATIC HANDLING –

Part 6-1: Bulk case packaging for miniaturized
surface mounting components
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC TS 60286-6-1 has been prepared by IEC technical committee 40: Capacitors and resistors
for electronic equipment. It is a Technical Specification.
The text of this Technical Specification is based on the following documents:
Draft Report on voting
40/3038/DTS 40/3066/RVDTS
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this Technical Specification is English.

– 4 – IEC TS 60286-6-1:2023 © IEC 2023
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at https://www.iec.ch/members_experts/refdocs. The main document types developed by IEC
are described in greater detail at https://www.iec.ch/standardsdev/publications.
A list of all parts in the IEC 60286 series, published under the general title Packaging of
components for automatic handling, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The "colour inside" logo on the cover page of this document indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this document using a colour printer.

INTRODUCTION
This Technical Specification was developed by the Technical Committee 40 Working group 36
on Components Packaging, in which the members such as assembly machine manufacturers,
component manufacturers and packaging material manufacturers had proposed, considered
and discussed the possible standardization on the application of a new type of bulk case to
contain smaller sizes of SMD, aiming to supplement IEC 60286-6 Edition 2.0, issued in 2004.
NOTE For size limitations of components, see Annex A, Table A.1 and Table A.2.
The International Electrotechnical Commission (IEC) draws attention to the fact that it is claimed
that compliance with this document may involve the use of a patent concerning “storage case
for surface mounting electronic components” .
IEC takes no position concerning the evidence, validity and scope of this patent right.
The holder of this patent right has assured the IEC that he/she is willing to negotiate licences
free of charge with applicants throughout the world for claims related to the items described in
this document. In this respect, the statement of the holder of this patent right is registered with
IEC. Information may be obtained from the patent database available at patents.iec.ch.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights other than those identified above. IEC shall not be held responsible for
identifying any or all such patent rights.

___________
Patent Application No.: PCT/JP2021/023093, published 17.06.2021

– 6 – IEC TS 60286-6-1:2023 © IEC 2023
PACKAGING OF COMPONENTS FOR AUTOMATIC HANDLING –

Part 6-1: Bulk case packaging for miniaturized
surface mounting compone
...