Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 16: Determination of volumetric swelling

ISO 13061-16:2017 specifies methods for the determination of volumetric swelling of wood.

Propriétés physiques et mécaniques du bois — Méthodes d'essais sur petites éprouvettes de bois sans défauts — Partie 16: Détermination du gonflement volumique

General Information

Status
Published
Publication Date
17-Jul-2017
Technical Committee
Current Stage
9020 - International Standard under periodical review
Due Date
15-Jul-2022
Completion Date
15-Jul-2022
Ref Project

RELATIONS

Buy Standard

Standard
ISO 13061-16:2017 - Physical and mechanical properties of wood -- Test methods for small clear wood specimens
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 13061-16
First edition
2017-06
Physical and mechanical properties of
wood — Test methods for small clear
wood specimens —
Part 16:
Determination of volumetric swelling
Propriétés physiques et mécaniques du bois — Méthodes d’essais sur
petites éprouvettes de bois sans défauts —
Partie 16: Détermination du gonflement volumique
Reference number
ISO 13061-16:2017(E)
ISO 2017
---------------------- Page: 1 ----------------------
ISO 13061-16:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 13061-16:2017(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 1

5 Stereometric method ....................................................................................................................................................................................... 1

5.1 Apparatus .................................................................................................................................................................................................... 1

5.2 Preparation of test pieces for stereometric method ............................................................................................... 2

5.3 Procedure .................................................................................................................................................................................................... 2

5.3.1 Determination of the dimensions of test pieces at absolutely dry (oven-

dry) condition ........................................................................................................................................... .......................... 2

5.3.2 Determination of the dimensions of test pieces in fully saturated condition ............. 2

5.4 Calculation and expression of results.................................................................................................................................. 3

6 Immersion method ............................................................................................................................................................................................ 3

6.1 Apparatus .................................................................................................................................................................................................... 3

6.2 Preparation of test pieces for immersion method ................................................................................................... 3

6.3 Procedure .................................................................................................................................................................................................... 3

6.3.1 Determination of the volume of test pieces at absolutely dry (oven-

dry) condition ........................................................................................................................................... .......................... 3

6.3.2 Determination of the volume of test pieces in fully saturated condition ........................ 4

6.4 Calculation and expression of results.................................................................................................................................. 4

7 Test report ................................................................................................................................................................................................................... 4

© ISO 2017 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 13061-16:2017(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO’s adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 218, Timber.

This first edition of ISO 13061-16 cancels and replaces ISO 4860:1982, which has been technically

revised. Changes have been made with regards to the sizes, moisture content of test pieces and

adjustment for moisture content.
A list of all parts in the ISO 13061 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 13061-16:2017(E)
Physical and mechanical properties of wood — Test
methods for small clear wood specimens —
Part 16:
Determination of volumetric swelling
1 Scope

This document specifies methods for the determination of volumetric swelling of wood.

2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 3129, Wood — Sampling methods and general requirements for physical and mechanical testing of

small clear wood specimens
ISO 24294, Timber — Round and sawn timber — Vocabulary
3 Terms and definitions

For the purpose of this document, the terms and definitions given in ISO 24294 apply.

ISO and IEC ma
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.