ISO 5216:2024
(Main)Commercial road vehicles — Ball-bearing turntable — Interchangeability
Commercial road vehicles — Ball-bearing turntable — Interchangeability
This document specifies dimensions of ball-bearing turntable when mounted on a vehicle which is part of vehicle combinations specified in of ISO 18868:2013, Clause 4, to ensure their interchangeability. This document also applies to the following: — drawbar trailers using a ball-bearing turntable to steer the front axle; — ball-bearing turntables assembled with the fifth-wheel of the road tractor (truck) to improve steering manoeuvre.
Véhicules routiers utilitaires — Plateau tournant à roulement à billes — Interchangeabilité
General Information
Buy Standard
Standards Content (Sample)
International
Standard
ISO 5216
First edition
Commercial road vehicles —
2024-04
Ball-bearing turntable —
Interchangeability
Véhicules routiers utilitaires — Plateau tournant à roulement à
billes — Interchangeabilité
Reference number
ISO 5216:2024(en) © ISO 2024
---------------------- Page: 1 ----------------------
ISO 5216:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO 5216:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Standard ball-bearing turntables geometrical requirements . 2
4.1 Radial section .2
4.2 Fixing holes .3
5 Designation . 3
Bibliography . 4
© ISO 2024 – All rights reserved
iii
---------------------- Page: 3 ----------------------
ISO 5216:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the
...
International
Standard
ISO 5216
First edition
Commercial road vehicles —
Ball-bearing turntable —
Interchangeability
Véhicules routiers utilitaires — Plateau tournant à roulement à
billes — Interchangeabilité
PROOF/ÉPREUVE
Reference number
ISO 5216:2024(en) © ISO 2024
---------------------- Page: 1 ----------------------
ISO 5216:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO 5216:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Standard ball-bearing turntables geometrical requirements . 2
4.1 Radial section .2
4.2 Fixing holes .3
5 Designation . 3
Bibliography . 4
PROOF/ÉPREUVE
© ISO 2024 – All rights reserved
iii
---------------------- Page: 3 ----------------------
ISO 5216:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this documen
...
Style Definition
ISO/PRF 5216 .
ISO/TC 22/SC 40 N Formatted
...
ISO/DIS 5216:2023(E)
Date: 2023-04-12
Secretariat: UNI Formatted
...
Date: 2024-02-13
Formatted: Font: 16 pt, Bold, English (United Kingdom)
Commercial road vehicles – — Ball-bearing turntable -—
Formatted: Cover Title_A1
Interchangeability
Formatted
...
Élément introductif — Élément central — Élément complémentaire
---------------------- Page: 1 ----------------------
Copyright notice
ThisVéhicules routiers utilitaires — Plateau tournant à roulement à billes — Interchangeabilité
PROOF
---------------------- Page: 2 ----------------------
ISO/DISPRF 5216:2023(E2024(en) Formatted: Font: Bold
Formatted: HeaderCentered, Left
Formatted: Font: Bold
Formatted: Font: Bold
© ISO document is a working draft2024
Formatted: Left: 42.55 pt, Right: 42.55 pt, Gutter: 0 pt,
Header distance from edge: 36 pt
All rights reserved. Unless otherwise specified, or committee draft and is copyright-protected by ISO. While required in
the reproductioncontext of working drafts or committee drafts in any form for use by participants in the ISO standards
Formatted: Indent: Left: 0 pt, Right: 0 pt, Space After: 0
development process is permitted without prior permission from ISO, neither its implementation, no part of this pt, Line spacing: single, Adjust space between Latin and
Asian text, Adjust space between Asian text and numbers
document nor any extract from itpublication may be reproduced, stored or utilized otherwise in any form or transmitted
in any form for any other purposeby any means, electronic or mechanical, including photocopying, or posting on the
internet or an intranet, without prior written permission from ISO. Permission can be requested from either ISO at the
address below or ISO’s member body in the country of the requester.
Requests for permission to reproduce this document for the purpose of selling it should be addressed as shown below
or to ISO's member body in the country of the requester:
[Indicate the full address, telephone number, fax number, telex number, and electronic mail address, as appropriate,
of the Copyright Manager of the ISO member body responsible for the secretariat of the TC or SC within the framework
of which the working document has been prepared.]
Reproduction for sales purposes may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
E-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
Formatted: FooterPageRomanNumber, Left
© ISO 2023 – All rights reserved iii
© ISO 2024 – All rights reserved
iii
---------------------- Page: 3 ----------------------
ISO/DISPRF 5216:2023(E2024(en) Formatted: Font: Bold
Formatted: HeaderCentered
Formatted: Font: Bold
Formatted: Font: Bold
Contents Page
Foreword . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Standard ball-bearing turntables geometrical requirements . 2
4.1 Radial section . 2
4.2 Fixing holes . 5
5 Designation . 6
Bibliography . 7
Foreword iv
1 Scope 1
2 Normative references 1
3 Terms and definitions 1
4 Standard ball races geometrical requirements 2
5 Designation 4
Formatted: FooterPageRomanNumber
iv © ISO 2023 – All rights reserved
© ISO 2024 – All rights reserved
iv
---------------------- Page: 4 ----------------------
ISO/DISPRF 5216:2023(E2024(en) Formatted: Font: Bold
Formatted: HeaderCentered, Left
Formatted: Font: Bold
Foreword Formatted: Font: Bold
ISO (the International Organization for Standardization) is a worldwide
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.